target/linux/ath79/dts/qca9563_yuncore_xd4200.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include "qca956x.dtsi"
   4
   5 #include <dt-bindings/gpio/gpio.h>
   6 #include <dt-bindings/input/input.h>
   7
   8 / {
   9         aliases {
  10                 label-mac-device = &eth0;
  11         };
  12
  13         keys {
  14                 compatible = "gpio-keys";
  15
  16                 reset {
  17                         linux,code = <KEY_RESTART>;
  18                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  19                         debounce-interval = <60>;
  20                 };
  21         };
  22 };
  23
  24 &eth0 {
  25         status = "okay";
  26
  27         pll-data = <0x03000101 0x00000101 0x00001919>;
  28
  29         nvmem-cells = <&macaddr_art_0>;
  30         nvmem-cell-names = "mac-address";
  31         phy-mode = "sgmii";
  32         phy-handle = <&phy0>;
  33 };
  34
  35 &mdio0 {
  36         status = "okay";
  37
  38         phy0: ethernet-phy@0 {
  39                 reg = <0>;
  40                 phy-mode = "sgmii";
  41
  42                 qca,ar8327-initvals = <
  43                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
  44                         0x10 0x81000080 /* POWER_ON_STRAP */
  45                         0x50 0xcf37cf37 /* LED_CTRL0 */
  46                         0x54 0xcf37cf37 /* LED_CTRL1 */
  47                         0x58 0xcf37cf37 /* LED_CTRL2 */
  48                         0x5c 0x0000c300 /* LED_CTRL3 */
  49                         0x7c 0x0000007e /* PORT0_STATUS */
  50                 >;
  51         };
  52 };
  53
  54 &pcie {
  55         status = "okay";
  56
  57         wifi@0,0 {
  58                 compatible = "pci168c,0056";
  59                 reg = <0x0000 0 0 0 0>;
  60                 nvmem-cells = <&precal_art_5000>;
  61                 nvmem-cell-names = "pre-calibration";
  62         };
  63 };
  64
  65 &spi {
  66         status = "okay";
  67
  68         flash@0 {
  69                 compatible = "jedec,spi-nor";
  70                 reg = <0>;
  71                 spi-max-frequency = <25000000>;
  72
  73                 partitions {
  74                         compatible = "fixed-partitions";
  75                         #address-cells = <1>;
  76                         #size-cells = <1>;
  77
  78                         partition@0 {
  79                                 label = "u-boot";
  80                                 reg = <0x000000 0x040000>;
  81                                 read-only;
  82                         };
  83
  84                         partition@40000 {
  85                                 label = "u-boot-env";
  86                                 reg = <0x040000 0x010000>;
  87                         };
  88
  89                         partition@50000 {
  90                                 compatible = "denx,uimage";
  91                                 label = "firmware";
  92                                 reg = <0x050000 0xfa0000>;
  93                         };
  94
  95                         art: partition@ff0000 {
  96                                 label = "art";
  97                                 reg = <0xff0000 0x010000>;
  98                                 read-only;
  99
 100                                 nvmem-layout {
 101                                         compatible = "fixed-layout";
 102                                         #address-cells = <1>;
 103                                         #size-cells = <1>;
 104
 105                                         macaddr_art_0: macaddr@0 {
 106                                                 reg = <0x0 0x6>;
 107                                         };
 108
 109                                         cal_art_5000: calibration@5000 {
 110                                                 reg = <0x5000 0x844>;
 111                                         };
 112
 113                                         precal_art_5000: pre-calibration@5000 {
 114                                                 reg = <0x5000 0x2f20>;
 115                                         };
 116                                 };
 117                         };
 118                 };
 119         };
 120 };
 121
 122 &wmac {
 123         status = "okay";
 124
 125         mtd-cal-data = <&art 0x1000>;
 126 };