--- /dev/null
+--- a/ath/if_ath_ahb.c
++++ b/ath/if_ath_ahb.c
+@@ -33,20 +33,15 @@
+ #include "if_ath_ahb.h"
+ #include "ah_soc.h"
+
+-#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,19)
+-#error "Kernel versions older than 2.6.19 are not supported!"
++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,28)
++#include <ar231x_platform.h>
+ #endif
+
+ struct ath_ahb_softc {
+ struct ath_softc aps_sc;
+-#ifdef CONFIG_PM
+- u32 aps_pmstate[16];
+-#endif
++ struct ar531x_config aps_config;
+ };
+
+-static struct ath_ahb_softc *sclist[2] = {NULL, NULL};
+-static u_int8_t num_activesc = 0;
+-
+ /*
+ * Module glue.
+ */
+@@ -101,13 +96,13 @@ ahb_enable_wmac(u_int16_t devid, u_int16
+ while (REG_READ(AR5315_PCI_MAC_PCICFG) & AR5315_PCI_MAC_PCICFG_SPWR_DN);
+ } else {
+ switch (wlanNum) {
+- case AR531X_WLAN0_NUM:
++ case 0:
+ reset = (AR531X_RESET_WLAN0 |
+ AR531X_RESET_WARM_WLAN0_MAC |
+ AR531X_RESET_WARM_WLAN0_BB);
+ enable = AR531X_ENABLE_WLAN0;
+ break;
+- case AR531X_WLAN1_NUM:
++ case 1:
+ reset = (AR531X_RESET_WLAN1 |
+ AR531X_RESET_WARM_WLAN1_MAC |
+ AR531X_RESET_WARM_WLAN1_BB);
+@@ -144,10 +139,10 @@ ahb_disable_wmac(u_int16_t devid, u_int1
+ *en &= ~AR5315_ARB_WLAN;
+ } else {
+ switch (wlanNum) {
+- case AR531X_WLAN0_NUM:
++ case 0:
+ enable = AR531X_ENABLE_WLAN0;
+ break;
+- case AR531X_WLAN1_NUM:
++ case 1:
+ enable = AR531X_ENABLE_WLAN1;
+ break;
+ default:
+@@ -159,29 +154,6 @@ ahb_disable_wmac(u_int16_t devid, u_int1
+ }
+
+
+-static int
+-exit_ath_wmac(u_int16_t wlanNum, struct ar531x_config *config)
+-{
+- struct ath_ahb_softc *sc = sclist[wlanNum];
+- struct net_device *dev;
+- u_int16_t devid;
+-
+- if (sc == NULL)
+- return -ENODEV; /* XXX: correct return value? */
+-
+- dev = sc->aps_sc.sc_dev;
+- ath_detach(dev);
+- if (dev->irq)
+- free_irq(dev->irq, dev);
+- devid = sc->aps_sc.devid;
+- config->tag = (void *)((unsigned long) devid);
+-
+- ahb_disable_wmac(devid, wlanNum);
+- free_netdev(dev);
+- sclist[wlanNum] = NULL;
+- return 0;
+-}
+-
+ static const char ubnt[] = "Ubiquiti Networks";
+ static const struct ath_hw_detect cards[] = {
+ {
+@@ -266,6 +238,114 @@ static const struct ath_hw_detect cards[
+ },
+ };
+
++static void
++ahb_hw_detect(struct ath_ahb_softc *sc, const char *radio)
++{
++ u16 *radio_data = (u16 *) radio;
++ if (radio_data) {
++ u16 vendor, id, subvendor, subid;
++ vendor = radio_data[1];
++ id = radio_data[0];
++ subvendor = radio_data[8];
++ subid = radio_data[7];
++ ath_hw_detect(&sc->aps_sc, cards, ARRAY_SIZE(cards), vendor, id, subvendor, subid);
++ }
++}
++
++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,28)
++
++static int ahb_wmac_probe(struct platform_device *pdev)
++{
++ struct ar231x_board_config *bcfg = pdev->dev.platform_data;
++ struct ath_ahb_softc *sc;
++ struct net_device *dev;
++ struct resource *res;
++ const char *athname;
++ int err;
++
++ ahb_enable_wmac(bcfg->devid, pdev->id);
++ dev = alloc_netdev(sizeof(struct ath_ahb_softc), "wifi%d", ether_setup);
++ if (!dev)
++ return -ENOMEM;
++
++ sc = dev->priv;
++ sc->aps_sc.sc_dev = dev;
++
++ dev->irq = platform_get_irq(pdev, 0);
++ if (dev->irq <= 0) {
++ printk("%s: Cannot find IRQ resource\n", dev->name);
++ goto error;
++ }
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ if (!res) {
++ printk("%s: Cannot find MMIO resource\n", dev->name);
++ goto error;
++ }
++
++ dev->mem_start = KSEG1ADDR(res->start);
++ dev->mem_end = KSEG1ADDR(res->end);
++ sc->aps_sc.sc_iobase = (void __iomem *) dev->mem_start;
++ sc->aps_sc.sc_bdev = NULL;
++
++ /* bus information for the HAL */
++ sc->aps_config.board = (const struct ar531x_boarddata *) bcfg->config;
++ sc->aps_config.radio = bcfg->radio;
++ sc->aps_config.unit = pdev->id;
++ sc->aps_config.tag = NULL;
++
++ err = ath_attach(bcfg->devid, dev, &sc->aps_config);
++ if (err != 0) {
++ printk("%s: ath_attach failed: %d\n", dev->name, err);
++ goto error;
++ }
++
++ athname = ath_hal_probe(ATHEROS_VENDOR_ID, bcfg->devid);
++ printk(KERN_INFO "%s: %s: %s: mem=0x%lx, irq=%d\n",
++ dev_info, dev->name, athname ? athname : "Atheros ???", dev->mem_start, dev->irq);
++
++ if (request_irq(dev->irq, ath_intr, IRQF_SHARED|IRQF_DISABLED, dev->name, dev)) {
++ printk(KERN_WARNING "%s: %s: request_irq failed\n", dev_info, dev->name);
++ goto error;
++ }
++
++ sc->aps_sc.sc_softled = 1; /* SoftLED over GPIO */
++ sc->aps_sc.sc_ledpin = bcfg->config->sysLedGpio;
++ sc->aps_sc.sc_invalid = 0;
++ ahb_hw_detect(sc, bcfg->radio);
++ platform_set_drvdata(pdev, dev);
++ return 0;
++
++error_dev:
++ free_irq(dev->irq, dev);
++error:
++ free_netdev(dev);
++
++ return -ENODEV;
++}
++
++
++static int ahb_wmac_remove(struct platform_device *pdev)
++{
++ struct ar231x_board_config *bcfg = pdev->dev.platform_data;
++ struct net_device *dev;
++
++ dev = platform_get_drvdata(pdev);
++ ath_detach(dev);
++
++ if (dev->irq)
++ free_irq(dev->irq, dev);
++
++ ahb_disable_wmac(bcfg->devid, pdev->id);
++ free_netdev(dev);
++
++ return 0;
++}
++
++#else
++
++static struct ath_ahb_softc *sclist[2] = {NULL, NULL};
++
+ static int
+ init_ath_wmac(u_int16_t devid, u_int16_t wlanNum, struct ar531x_config *config)
+ {
+@@ -318,7 +398,7 @@ init_ath_wmac(u_int16_t devid, u_int16_t
+ sc->aps_sc.sc_iobase = (void __iomem *) dev->mem_start;
+ sc->aps_sc.sc_bdev = NULL;
+
+- if (request_irq(dev->irq, ath_intr, IRQF_SHARED, dev->name, dev)) {
++ if (request_irq(dev->irq, ath_intr, IRQF_SHARED|IRQF_DISABLED, dev->name, dev)) {
+ printk(KERN_WARNING "%s: %s: request_irq failed\n", dev_info, dev->name);
+ goto bad3;
+ }
+@@ -328,21 +408,12 @@ init_ath_wmac(u_int16_t devid, u_int16_t
+ athname = ath_hal_probe(ATHEROS_VENDOR_ID, devid);
+ printk(KERN_INFO "%s: %s: %s: mem=0x%lx, irq=%d\n",
+ dev_info, dev->name, athname ? athname : "Atheros ???", dev->mem_start, dev->irq);
+- num_activesc++;
+ /* Ready to process interrupts */
+
+ sc->aps_sc.sc_softled = 1; /* SoftLED over GPIO */
+ sc->aps_sc.sc_ledpin = config->board->sysLedGpio;
+ sc->aps_sc.sc_invalid = 0;
+- radio_data = (u16 *) config->radio;
+- if (radio_data) {
+- u16 vendor, id, subvendor, subid;
+- vendor = radio_data[1];
+- id = radio_data[0];
+- subvendor = radio_data[8];
+- subid = radio_data[7];
+- ath_hw_detect(&sc->aps_sc, cards, ARRAY_SIZE(cards), vendor, id, subvendor, subid);
+- }
++ ahb_hw_detect(sc, config->radio);
+
+ return 0;
+
+@@ -357,6 +428,29 @@ init_ath_wmac(u_int16_t devid, u_int16_t
+ return -ENODEV;
+ }
+
++static int
++exit_ath_wmac(u_int16_t wlanNum, struct ar531x_config *config)
++{
++ struct ath_ahb_softc *sc = sclist[wlanNum];
++ struct net_device *dev;
++ u_int16_t devid;
++
++ if (sc == NULL)
++ return -ENODEV; /* XXX: correct return value? */
++
++ dev = sc->aps_sc.sc_dev;
++ ath_detach(dev);
++ if (dev->irq)
++ free_irq(dev->irq, dev);
++ devid = sc->aps_sc.devid;
++ config->tag = (void *)((unsigned long) devid);
++
++ ahb_disable_wmac(devid, wlanNum);
++ free_netdev(dev);
++ sclist[wlanNum] = NULL;
++ return 0;
++}
++
+ static int ahb_wmac_probe(struct platform_device *pdev)
+ {
+ u_int16_t devid;
+@@ -377,11 +471,18 @@ static int ahb_wmac_remove(struct platfo
+ return 0;
+ }
+
++#endif
++
+ static struct platform_driver ahb_wmac_driver = {
++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,28)
++ .driver.name = "ar231x-wmac",
++#else
+ .driver.name = "ar531x-wmac",
++#endif
+ .probe = ahb_wmac_probe,
+ .remove = ahb_wmac_remove
+ };
++
+ int
+ ath_ioctl_ethtool(struct ath_softc *sc, int cmd, void __user *addr)
+ {
CONFIG_32BIT=y
# CONFIG_64BIT is not set
-CONFIG_AR2313=y
+CONFIG_AR231X_ETHERNET=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_ARCH_SUPPORTS_OPROFILE=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ATHEROS=y
+CONFIG_ATHEROS_AR2315=y
+CONFIG_ATHEROS_AR2315_PCI=y
CONFIG_ATHEROS_AR5312=y
-CONFIG_ATHEROS_AR5315=y
-CONFIG_ATHEROS_AR5315_PCI=y
CONFIG_ATHEROS_WDT=y
-# CONFIG_ATM is not set
-# CONFIG_ATMEL is not set
CONFIG_BASE_SMALL=0
# CONFIG_BCM47XX is not set
CONFIG_BITREVERSE=y
-# CONFIG_BT is not set
CONFIG_CEVT_R4K=y
CONFIG_CLASSIC_RCU=y
CONFIG_CMDLINE="console=ttyS0,9600 rootfstype=squashfs,jffs2 init=/etc/preinit"
# CONFIG_CPU_TX39XX is not set
# CONFIG_CPU_TX49XX is not set
# CONFIG_CPU_VR41XX is not set
-# CONFIG_CRYPTO_AEAD2 is not set
-# CONFIG_CRYPTO_ALGAPI2 is not set
-# CONFIG_CRYPTO_BLKCIPHER2 is not set
-# CONFIG_CRYPTO_HASH2 is not set
-# CONFIG_CRYPTO_MANAGER2 is not set
-# CONFIG_CRYPTO_RNG2 is not set
CONFIG_CSRC_R4K=y
CONFIG_DEVPORT=y
# CONFIG_DM9000 is not set
CONFIG_DMA_NONCOHERENT=y
# CONFIG_FIXED_PHY is not set
# CONFIG_FREEZER is not set
-CONFIG_FS_POSIX_ACL=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_GENERIC_CMOS_UPDATE=y
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_HAVE_IDE=y
CONFIG_HAVE_OPROFILE=y
-# CONFIG_HERMES is not set
CONFIG_HW_HAS_PCI=y
CONFIG_HW_RANDOM=y
# CONFIG_I2C is not set
CONFIG_ICPLUS_PHY=y
# CONFIG_IDE is not set
CONFIG_INITRAMFS_SOURCE=""
-# CONFIG_IPW2100 is not set
-# CONFIG_IPW2200 is not set
CONFIG_IRQ_CPU=y
# CONFIG_ISDN is not set
CONFIG_KMOD=y
# CONFIG_MIPS_SIM is not set
CONFIG_MTD=y
# CONFIG_MTD_ABSENT is not set
+CONFIG_MTD_AR2315=y
CONFIG_MTD_BLKDEVS=y
CONFIG_MTD_BLOCK=y
# CONFIG_MTD_BLOCK2MTD is not set
CONFIG_MTD_REDBOOT_PARTS_READONLY=y
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_SLRAM is not set
-CONFIG_MTD_SPIFLASH=y
# CONFIG_NET_PCI is not set
-CONFIG_NF_CT_ACCT=y
# CONFIG_NF_DEFRAG_IPV4 is not set
# CONFIG_NO_IOPORT is not set
# CONFIG_NXP_STB220 is not set
# CONFIG_PNX8550_STB810 is not set
# CONFIG_PROBE_INITRD_HEADER is not set
# CONFIG_PROM_EMU is not set
-CONFIG_RFKILL_LEDS=y
CONFIG_RTC_LIB=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
-# CONFIG_SCSI_WAIT_SCAN is not set
+# CONFIG_SCSI_DMA is not set
# CONFIG_SERIAL_8250_EXTENDED is not set
CONFIG_SERIAL_8250_NR_UARTS=1
CONFIG_SERIAL_8250_RUNTIME_UARTS=1
# CONFIG_SIBYTE_RHONE is not set
# CONFIG_SIBYTE_SENTOSA is not set
# CONFIG_SIBYTE_SWARM is not set
-CONFIG_SND_MIPS=y
# CONFIG_SOFT_WATCHDOG is not set
-CONFIG_SOUND_OSS_CORE=y
CONFIG_SSB_POSSIBLE=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
CONFIG_TICK_ONESHOT=y
CONFIG_TRAD_SIGNALS=y
-# CONFIG_USB is not set
-# CONFIG_USB_EHCI_HCD is not set
-CONFIG_USB_STORAGE_CYPRESS_ATACB=y
CONFIG_USB_SUPPORT=y
-# CONFIG_USB_UHCI_HCD is not set
-# CONFIG_USB_WDM is not set
# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_MEDIA is not set
-# CONFIG_VIDEO_V4L2 is not set
-# CONFIG_VIDEO_V4L2_COMMON is not set
CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
-config ATHEROS_AR5312
- bool "Atheros 5312/2312+ support"
- depends on ATHEROS
- default y
-
-config ATHEROS_AR5315
- bool "Atheros 5315/2315+ support"
- depends on ATHEROS
- select DMA_NONCOHERENT
- select CEVT_R4K
- select CSRC_R4K
- select IRQ_CPU
- select SYS_HAS_CPU_MIPS32_R1
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select GENERIC_GPIO
- default y
-
-config ATHEROS_AR5315_PCI
- bool "PCI support"
- select HW_HAS_PCI
- select PCI
- select USB_ARCH_HAS_HCD
- select USB_ARCH_HAS_OHCI
- select USB_ARCH_HAS_EHCI
- depends on ATHEROS_AR5315
- default n
+++ /dev/null
-#
-# This file is subject to the terms and conditions of the GNU General Public
-# License. See the file "COPYING" in the main directory of this archive
-# for more details.
-#
-# Copyright (C) 2006 FON Technology, SL.
-# Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-# Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
-#
-
-obj-y += board.o prom.o reset.o
-obj-$(CONFIG_ATHEROS_AR5312) += ar5312/
-obj-$(CONFIG_ATHEROS_AR5315) += ar5315/
+++ /dev/null
-#
-# This file is subject to the terms and conditions of the GNU General Public
-# License. See the file "COPYING" in the main directory of this archive
-# for more details.
-#
-# Copyright (C) 2007 FON Technology, SL.
-# Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
-# Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
-#
-
-obj-y := board.o irq.o
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-/*
- * Platform devices for Atheros SoCs
- */
-
-#include <linux/autoconf.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/mtd/physmap.h>
-#include <linux/platform_device.h>
-#include <linux/kernel.h>
-#include <linux/reboot.h>
-#include <asm/bootinfo.h>
-#include <asm/reboot.h>
-#include <asm/time.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <ar531x.h>
-#include <linux/leds.h>
-
-#define NO_PHY 0x1f
-
-static int is_5312 = 0;
-static struct platform_device *ar5312_devs[6];
-
-static struct resource ar5312_eth0_res[] = {
- {
- .name = "eth0_membase",
- .flags = IORESOURCE_MEM,
- .start = KSEG1ADDR(AR531X_ENET0),
- .end = KSEG1ADDR(AR531X_ENET0 + 0x2000),
- },
- {
- .name = "eth0_irq",
- .flags = IORESOURCE_IRQ,
- .start = AR5312_IRQ_ENET0_INTRS,
- .end = AR5312_IRQ_ENET0_INTRS,
- },
-};
-static struct ar531x_eth ar5312_eth0_data = {
- .phy = NO_PHY,
- .mac = 0,
- .reset_base = AR531X_RESET,
- .reset_mac = AR531X_RESET_ENET0,
- .reset_phy = AR531X_RESET_EPHY0,
- .phy_base = KSEG1ADDR(AR531X_ENET0),
-};
-
-static struct resource ar5312_eth1_res[] = {
- {
- .name = "eth1_membase",
- .flags = IORESOURCE_MEM,
- .start = KSEG1ADDR(AR531X_ENET1),
- .end = KSEG1ADDR(AR531X_ENET1 + 0x2000),
- },
- {
- .name = "eth1_irq",
- .flags = IORESOURCE_IRQ,
- .start = AR5312_IRQ_ENET1_INTRS,
- .end = AR5312_IRQ_ENET1_INTRS,
- },
-};
-static struct ar531x_eth ar5312_eth1_data = {
- .phy = NO_PHY,
- .mac = 1,
- .reset_base = AR531X_RESET,
- .reset_mac = AR531X_RESET_ENET1,
- .reset_phy = AR531X_RESET_EPHY1,
- .phy_base = KSEG1ADDR(AR531X_ENET1),
-};
-
-static struct platform_device ar5312_eth[] = {
- {
- .id = 0,
- .name = "ar531x-eth",
- .dev.platform_data = &ar5312_eth0_data,
- .resource = ar5312_eth0_res,
- .num_resources = ARRAY_SIZE(ar5312_eth0_res)
- },
- {
- .id = 1,
- .name = "ar531x-eth",
- .dev.platform_data = &ar5312_eth1_data,
- .resource = ar5312_eth1_res,
- .num_resources = ARRAY_SIZE(ar5312_eth1_res)
- },
-};
-
-
-/*
- * AR2312/3 ethernet uses the PHY of ENET0, but the MAC
- * of ENET1. Atheros calls it 'twisted' for a reason :)
- */
-static struct resource ar231x_eth0_res[] = {
- {
- .name = "eth0_membase",
- .flags = IORESOURCE_MEM,
- .start = KSEG1ADDR(AR531X_ENET1),
- .end = KSEG1ADDR(AR531X_ENET1 + 0x2000),
- },
- {
- .name = "eth0_irq",
- .flags = IORESOURCE_IRQ,
- .start = AR5312_IRQ_ENET1_INTRS,
- .end = AR5312_IRQ_ENET1_INTRS,
- },
-};
-static struct ar531x_eth ar231x_eth0_data = {
- .phy = 1,
- .mac = 1,
- .reset_base = AR531X_RESET,
- .reset_mac = AR531X_RESET_ENET1,
- .reset_phy = AR531X_RESET_EPHY1,
- .phy_base = KSEG1ADDR(AR531X_ENET0),
-};
-static struct platform_device ar231x_eth0 = {
- .id = 0,
- .name = "ar531x-eth",
- .dev.platform_data = &ar231x_eth0_data,
- .resource = ar231x_eth0_res,
- .num_resources = ARRAY_SIZE(ar231x_eth0_res)
-};
-
-
-static struct platform_device ar5312_wmac[] = {
- {
- .id = 0,
- .name = "ar531x-wmac",
- },
- {
- .id = 1,
- .name = "ar531x-wmac",
- },
-};
-
-static struct physmap_flash_data ar5312_flash_data = {
- .width = 2,
-};
-
-static struct resource ar5312_flash_resource = {
- .start = AR531X_FLASH,
- .end = AR531X_FLASH + 0x800000 - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ar5312_physmap_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &ar5312_flash_data,
- },
- .num_resources = 1,
- .resource = &ar5312_flash_resource,
-};
-
-#ifdef CONFIG_LEDS_GPIO
-static struct gpio_led ar5312_leds[] = {
- { .name = "wlan", .gpio = 0, .active_low = 1, },
-};
-
-static const struct gpio_led_platform_data ar5312_led_data = {
- .num_leds = ARRAY_SIZE(ar5312_leds),
- .leds = (void *) ar5312_leds,
-};
-
-static struct platform_device ar5312_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = (void *) &ar5312_led_data,
- }
-};
-#endif
-
-/*
- * NB: This mapping size is larger than the actual flash size,
- * but this shouldn't be a problem here, because the flash
- * will simply be mapped multiple times.
- */
-static char __init *ar5312_flash_limit(void)
-{
- u32 ctl;
- /*
- * Configure flash bank 0.
- * Assume 8M window size. Flash will be aliased if it's smaller
- */
- ctl = FLASHCTL_E |
- FLASHCTL_AC_8M |
- FLASHCTL_RBLE |
- (0x01 << FLASHCTL_IDCY_S) |
- (0x07 << FLASHCTL_WST1_S) |
- (0x07 << FLASHCTL_WST2_S) |
- (sysRegRead(AR531X_FLASHCTL0) & FLASHCTL_MW);
-
- sysRegWrite(AR531X_FLASHCTL0, ctl);
-
- /* Disable other flash banks */
- sysRegWrite(AR531X_FLASHCTL1,
- sysRegRead(AR531X_FLASHCTL1) & ~(FLASHCTL_E | FLASHCTL_AC));
-
- sysRegWrite(AR531X_FLASHCTL2,
- sysRegRead(AR531X_FLASHCTL2) & ~(FLASHCTL_E | FLASHCTL_AC));
-
- return (char *) KSEG1ADDR(AR531X_FLASH + 0x800000);
-}
-
-static struct ar531x_config __init *init_wmac(int unit)
-{
- struct ar531x_config *config;
-
- config = (struct ar531x_config *) kzalloc(sizeof(struct ar531x_config), GFP_KERNEL);
- config->board = board_config;
- config->radio = radio_config;
- config->unit = unit;
- config->tag = (u_int16_t) ((sysRegRead(AR531X_REV) >> AR531X_REV_WMAC_MIN_S) & AR531X_REV_CHIP);
-
- return config;
-}
-
-int __init ar5312_init_devices(void)
-{
- struct ar531x_boarddata *bcfg;
- char *radio, *c;
- int dev = 0;
- uint32_t fctl = 0;
-
- if (!is_5312)
- return 0;
-
- /* Locate board/radio config data */
- ar531x_find_config(ar5312_flash_limit());
- bcfg = (struct ar531x_boarddata *) board_config;
-
-
- /*
- * Chip IDs and hardware detection for some Atheros
- * models are really broken!
- *
- * Atheros uses a disabled WMAC0 and Silicon ID of AR5312
- * as indication for AR2312, which is otherwise
- * indistinguishable from the real AR5312.
- */
- if (radio_config) {
- radio = radio_config + AR531X_RADIO_MASK_OFF;
- if ((*((u32 *) radio) & AR531X_RADIO0_MASK) == 0)
- bcfg->config |= BD_ISCASPER;
- } else
- radio = NULL;
-
- /* AR2313 has CPU minor rev. 10 */
- if ((current_cpu_data.processor_id & 0xff) == 0x0a)
- mips_machtype = MACH_ATHEROS_AR2313;
-
- /* AR2312 shares the same Silicon ID as AR5312 */
- else if (bcfg->config & BD_ISCASPER)
- mips_machtype = MACH_ATHEROS_AR2312;
-
- /* Everything else is probably AR5312 or compatible */
- else
- mips_machtype = MACH_ATHEROS_AR5312;
-
- ar5312_eth0_data.board_config = board_config;
- ar5312_eth1_data.board_config = board_config;
-
- /* fixup flash width */
- fctl = sysRegRead(AR531X_FLASHCTL) & FLASHCTL_MW;
- switch (fctl) {
- case FLASHCTL_MWx16:
- ar5312_flash_data.width = 2;
- break;
- case FLASHCTL_MWx8:
- default:
- ar5312_flash_data.width = 1;
- break;
- }
-
- ar5312_devs[dev++] = &ar5312_physmap_flash;
-
-#ifdef CONFIG_LEDS_GPIO
- ar5312_leds[0].gpio = bcfg->sysLedGpio;
- ar5312_devs[dev++] = &ar5312_gpio_leds;
-#endif
-
- if (!memcmp(bcfg->enet0Mac, "\xff\xff\xff\xff\xff\xff", 6))
- memcpy(bcfg->enet0Mac, bcfg->enet1Mac, 6);
-
- if (memcmp(bcfg->enet0Mac, bcfg->enet1Mac, 6) == 0) {
- /* ENET0 and ENET1 have the same mac.
- * Increment the one from ENET1 */
- c = bcfg->enet1Mac + 5;
- while ((c >= (char *) bcfg->enet1Mac) && !(++(*c)))
- c--;
- }
-
- switch(mips_machtype) {
- case MACH_ATHEROS_AR5312:
- ar5312_eth0_data.macaddr = bcfg->enet0Mac;
- ar5312_eth1_data.macaddr = bcfg->enet1Mac;
- ar5312_devs[dev++] = &ar5312_eth[0];
- ar5312_devs[dev++] = &ar5312_eth[1];
- break;
- case MACH_ATHEROS_AR2312:
- case MACH_ATHEROS_AR2313:
- ar231x_eth0_data.macaddr = bcfg->enet0Mac;
- ar5312_devs[dev++] = &ar231x_eth0;
- ar5312_flash_data.width = 1;
- break;
- }
-
- if (radio) {
- if (mips_machtype == MACH_ATHEROS_AR5312) {
- if (*((u32 *) radio) & AR531X_RADIO0_MASK) {
- ar5312_wmac[0].dev.platform_data = init_wmac(0);
- ar5312_devs[dev++] = &ar5312_wmac[0];
- }
- }
- if (*((u32 *) radio) & AR531X_RADIO1_MASK) {
- ar5312_wmac[1].dev.platform_data = init_wmac(1);
- ar5312_devs[dev++] = &ar5312_wmac[1];
- }
- }
-
- return platform_add_devices(ar5312_devs, dev);
-}
-
-
-static void ar5312_halt(void)
-{
- while (1);
-}
-
-static void ar5312_power_off(void)
-{
- ar5312_halt();
-}
-
-
-static void ar5312_restart(char *command)
-{
- /* reset the system */
- for(;;) sysRegWrite(AR531X_RESET, AR531X_RESET_SYSTEM);
-}
-
-
-/*
- * This table is indexed by bits 5..4 of the CLOCKCTL1 register
- * to determine the predevisor value.
- */
-static int __initdata CLOCKCTL1_PREDIVIDE_TABLE[4] = {
- 1,
- 2,
- 4,
- 5
-};
-
-
-static unsigned int __init ar5312_cpu_frequency(void)
-{
- unsigned int result;
- unsigned int predivide_mask, predivide_shift;
- unsigned int multiplier_mask, multiplier_shift;
- unsigned int clockCtl1, preDivideSelect, preDivisor, multiplier;
- unsigned int doubler_mask;
- unsigned int wisoc_revision;
-
- /* Trust the bootrom's idea of cpu frequency. */
- if ((result = sysRegRead(AR5312_SCRATCH)))
- return result;
-
- wisoc_revision = (sysRegRead(AR531X_REV) & AR531X_REV_MAJ) >> AR531X_REV_MAJ_S;
- if (wisoc_revision == AR531X_REV_MAJ_AR2313) {
- predivide_mask = AR2313_CLOCKCTL1_PREDIVIDE_MASK;
- predivide_shift = AR2313_CLOCKCTL1_PREDIVIDE_SHIFT;
- multiplier_mask = AR2313_CLOCKCTL1_MULTIPLIER_MASK;
- multiplier_shift = AR2313_CLOCKCTL1_MULTIPLIER_SHIFT;
- doubler_mask = AR2313_CLOCKCTL1_DOUBLER_MASK;
- } else { /* AR5312 and AR2312 */
- predivide_mask = AR5312_CLOCKCTL1_PREDIVIDE_MASK;
- predivide_shift = AR5312_CLOCKCTL1_PREDIVIDE_SHIFT;
- multiplier_mask = AR5312_CLOCKCTL1_MULTIPLIER_MASK;
- multiplier_shift = AR5312_CLOCKCTL1_MULTIPLIER_SHIFT;
- doubler_mask = AR5312_CLOCKCTL1_DOUBLER_MASK;
- }
-
- /*
- * Clocking is derived from a fixed 40MHz input clock.
- *
- * cpuFreq = InputClock * MULT (where MULT is PLL multiplier)
- * sysFreq = cpuFreq / 4 (used for APB clock, serial,
- * flash, Timer, Watchdog Timer)
- *
- * cntFreq = cpuFreq / 2 (use for CPU count/compare)
- *
- * So, for example, with a PLL multiplier of 5, we have
- *
- * cpuFreq = 200MHz
- * sysFreq = 50MHz
- * cntFreq = 100MHz
- *
- * We compute the CPU frequency, based on PLL settings.
- */
-
- clockCtl1 = sysRegRead(AR5312_CLOCKCTL1);
- preDivideSelect = (clockCtl1 & predivide_mask) >> predivide_shift;
- preDivisor = CLOCKCTL1_PREDIVIDE_TABLE[preDivideSelect];
- multiplier = (clockCtl1 & multiplier_mask) >> multiplier_shift;
-
- if (clockCtl1 & doubler_mask) {
- multiplier = multiplier << 1;
- }
- return (40000000 / preDivisor) * multiplier;
-}
-
-static inline int ar5312_sys_frequency(void)
-{
- return ar5312_cpu_frequency() / 4;
-}
-
-static void __init ar5312_time_init(void)
-{
- mips_hpt_frequency = ar5312_cpu_frequency() / 2;
-}
-
-
-void __init ar5312_prom_init(void)
-{
- u32 memsize, memcfg, bank0AC, bank1AC;
-
- is_5312 = 1;
-
- /* Detect memory size */
- memcfg = sysRegRead(AR531X_MEM_CFG1);
- bank0AC = (memcfg & MEM_CFG1_AC0) >> MEM_CFG1_AC0_S;
- bank1AC = (memcfg & MEM_CFG1_AC1) >> MEM_CFG1_AC1_S;
- memsize = (bank0AC ? (1 << (bank0AC+1)) : 0)
- + (bank1AC ? (1 << (bank1AC+1)) : 0);
- memsize <<= 20;
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-
- /* Initialize it to AR5312 for now. Real detection will be done
- * in ar5312_init_devices() */
- mips_machtype = MACH_ATHEROS_AR5312;
-}
-
-void __init ar5312_plat_setup(void)
-{
- /* Clear any lingering AHB errors */
- sysRegRead(AR531X_PROCADDR);
- sysRegRead(AR531X_DMAADDR);
- sysRegWrite(AR531X_WD_CTRL, AR531X_WD_CTRL_IGNORE_EXPIRATION);
-
- board_time_init = ar5312_time_init;
-
- _machine_restart = ar5312_restart;
- _machine_halt = ar5312_halt;
- pm_power_off = ar5312_power_off;
-
- serial_setup(KSEG1ADDR(AR531X_UART0), ar5312_sys_frequency());
-}
-
-arch_initcall(ar5312_init_devices);
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-/*
- * Platform devices for Atheros SoCs
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-#include <linux/reboot.h>
-#include <asm/bootinfo.h>
-#include <asm/time.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-
-#include <ar531x.h>
-#include <gpio.h>
-
-/*
- * Called when an interrupt is received, this function
- * determines exactly which interrupt it was, and it
- * invokes the appropriate handler.
- *
- * Implicitly, we also define interrupt priority by
- * choosing which to dispatch first.
- */
-asmlinkage void ar5312_irq_dispatch(void)
-{
- int pending = read_c0_status() & read_c0_cause();
-
- if (pending & CAUSEF_IP2)
- do_IRQ(AR5312_IRQ_WLAN0_INTRS);
- else if (pending & CAUSEF_IP3)
- do_IRQ(AR5312_IRQ_ENET0_INTRS);
- else if (pending & CAUSEF_IP4)
- do_IRQ(AR5312_IRQ_ENET1_INTRS);
- else if (pending & CAUSEF_IP5)
- do_IRQ(AR5312_IRQ_WLAN1_INTRS);
- else if (pending & CAUSEF_IP6) {
- unsigned int ar531x_misc_intrs = sysRegRead(AR531X_ISR) & sysRegRead(AR531X_IMR);
-
- if (ar531x_misc_intrs & AR531X_ISR_TIMER) {
- do_IRQ(AR531X_MISC_IRQ_TIMER);
- (void)sysRegRead(AR531X_TIMER);
- } else if (ar531x_misc_intrs & AR531X_ISR_AHBPROC)
- do_IRQ(AR531X_MISC_IRQ_AHB_PROC);
- else if ((ar531x_misc_intrs & AR531X_ISR_UART0))
- do_IRQ(AR531X_MISC_IRQ_UART0);
- else if (ar531x_misc_intrs & AR531X_ISR_WD)
- do_IRQ(AR531X_MISC_IRQ_WATCHDOG);
- else
- do_IRQ(AR531X_MISC_IRQ_NONE);
- } else if (pending & CAUSEF_IP7) {
- do_IRQ(AR531X_IRQ_CPU_CLOCK);
- }
-}
-
-
-/* Enable the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5312_misc_intr_enable(unsigned int irq)
-{
- unsigned int imr;
-
- imr = sysRegRead(AR531X_IMR);
- imr |= (1 << (irq - AR531X_MISC_IRQ_BASE - 1));
- sysRegWrite(AR531X_IMR, imr);
- sysRegRead(AR531X_IMR); /* flush write buffer */
-}
-
-/* Disable the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5312_misc_intr_disable(unsigned int irq)
-{
- unsigned int imr;
-
- imr = sysRegRead(AR531X_IMR);
- imr &= ~(1 << (irq - AR531X_MISC_IRQ_BASE - 1));
- sysRegWrite(AR531X_IMR, imr);
- sysRegRead(AR531X_IMR); /* flush write buffer */
-}
-
-/* Turn on the specified AR531X_MISC_IRQ interrupt */
-static unsigned int
-ar5312_misc_intr_startup(unsigned int irq)
-{
- ar5312_misc_intr_enable(irq);
- return 0;
-}
-
-/* Turn off the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5312_misc_intr_shutdown(unsigned int irq)
-{
- ar5312_misc_intr_disable(irq);
-}
-
-static void
-ar5312_misc_intr_ack(unsigned int irq)
-{
- ar5312_misc_intr_disable(irq);
-}
-
-static void
-ar5312_misc_intr_end(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- ar5312_misc_intr_enable(irq);
-}
-
-static struct irq_chip ar5312_misc_intr_controller = {
- .typename = "AR5312 misc",
- .startup = ar5312_misc_intr_startup,
- .shutdown = ar5312_misc_intr_shutdown,
- .enable = ar5312_misc_intr_enable,
- .disable = ar5312_misc_intr_disable,
- .ack = ar5312_misc_intr_ack,
- .end = ar5312_misc_intr_end,
-};
-
-static irqreturn_t ar5312_ahb_proc_handler(int cpl, void *dev_id)
-{
- u32 proc1 = sysRegRead(AR531X_PROC1);
- u32 procAddr = sysRegRead(AR531X_PROCADDR); /* clears error state */
- u32 dma1 = sysRegRead(AR531X_DMA1);
- u32 dmaAddr = sysRegRead(AR531X_DMAADDR); /* clears error state */
-
- printk("AHB interrupt: PROCADDR=0x%8.8x PROC1=0x%8.8x DMAADDR=0x%8.8x DMA1=0x%8.8x\n",
- procAddr, proc1, dmaAddr, dma1);
-
- machine_restart("AHB error"); /* Catastrophic failure */
- return IRQ_HANDLED;
-}
-
-
-static struct irqaction ar5312_ahb_proc_interrupt = {
- .handler = ar5312_ahb_proc_handler,
- .flags = IRQF_DISABLED,
- .name = "ar5312_ahb_proc_interrupt",
-};
-
-
-static struct irqaction cascade = {
- .handler = no_action,
- .flags = IRQF_DISABLED,
- .name = "cascade",
-};
-
-void __init ar5312_misc_intr_init(int irq_base)
-{
- int i;
-
- for (i = irq_base; i < irq_base + AR531X_MISC_IRQ_COUNT; i++) {
- irq_desc[i].status = IRQ_DISABLED;
- irq_desc[i].action = NULL;
- irq_desc[i].depth = 1;
- irq_desc[i].chip = &ar5312_misc_intr_controller;
- }
- setup_irq(AR531X_MISC_IRQ_AHB_PROC, &ar5312_ahb_proc_interrupt);
- setup_irq(AR5312_IRQ_MISC_INTRS, &cascade);
-}
-
-
+++ /dev/null
-#
-# This file is subject to the terms and conditions of the GNU General Public
-# License. See the file "COPYING" in the main directory of this archive
-# for more details.
-#
-# Copyright (C) 2007 FON Technology, SL.
-# Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
-# Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
-#
-
-obj-y := board.o irq.o
-obj-$(CONFIG_ATHEROS_AR5315_PCI) += pci.o
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-/*
- * Platform devices for Atheros SoCs
- */
-
-#include <linux/autoconf.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/platform_device.h>
-#include <linux/kernel.h>
-#include <linux/reboot.h>
-#include <linux/delay.h>
-#include <asm/bootinfo.h>
-#include <asm/reboot.h>
-#include <asm/time.h>
-#include <asm/irq.h>
-#include <asm/io.h>
-#include <ar531x.h>
-#include <linux/leds.h>
-#include <asm/gpio.h>
-
-static int is_5315 = 0;
-
-static struct resource ar5315_eth_res[] = {
- {
- .name = "eth0_membase",
- .flags = IORESOURCE_MEM,
- .start = AR5315_ENET0,
- .end = AR5315_ENET0 + 0x2000,
- },
- {
- .name = "eth0_irq",
- .flags = IORESOURCE_IRQ,
- .start = AR5315_IRQ_ENET0_INTRS,
- .end = AR5315_IRQ_ENET0_INTRS,
- },
-};
-
-static struct ar531x_eth ar5315_eth_data = {
- .phy = 1,
- .mac = 0,
- .reset_base = AR5315_RESET,
- .reset_mac = AR5315_RESET_ENET0,
- .reset_phy = AR5315_RESET_EPHY0,
- .phy_base = AR5315_ENET0
-};
-
-static struct platform_device ar5315_eth = {
- .id = 0,
- .name = "ar531x-eth",
- .dev.platform_data = &ar5315_eth_data,
- .resource = ar5315_eth_res,
- .num_resources = ARRAY_SIZE(ar5315_eth_res)
-};
-
-static struct platform_device ar5315_wmac = {
- .id = 0,
- .name = "ar531x-wmac",
- /* FIXME: add resources */
-};
-
-static struct resource ar5315_spiflash_res[] = {
- {
- .name = "flash_base",
- .flags = IORESOURCE_MEM,
- .start = KSEG1ADDR(AR5315_SPI_READ),
- .end = KSEG1ADDR(AR5315_SPI_READ) + 0x800000,
- },
- {
- .name = "flash_regs",
- .flags = IORESOURCE_MEM,
- .start = 0x11300000,
- .end = 0x11300012,
- },
-};
-
-static struct platform_device ar5315_spiflash = {
- .id = 0,
- .name = "spiflash",
- .resource = ar5315_spiflash_res,
- .num_resources = ARRAY_SIZE(ar5315_spiflash_res)
-};
-
-#ifdef CONFIG_LEDS_GPIO
-static struct gpio_led ar5315_leds[8];
-
-static struct gpio_led_platform_data ar5315_led_data = {
- .num_leds = ARRAY_SIZE(ar5315_leds),
- .leds = (void *) ar5315_leds,
-};
-
-static struct platform_device ar5315_gpio_leds = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = (void *) &ar5315_led_data,
- }
-};
-#endif
-
-static struct platform_device ar5315_wdt =
-{
- .id = 0,
- .name = "ar2315_wdt",
-};
-
-static __initdata struct platform_device *ar5315_devs[6];
-
-static void *flash_regs;
-
-static inline __u32 spiflash_regread32(int reg)
-{
- volatile __u32 *data = (__u32 *)(flash_regs + reg);
-
- return (*data);
-}
-
-static inline void spiflash_regwrite32(int reg, __u32 data)
-{
- volatile __u32 *addr = (__u32 *)(flash_regs + reg);
-
- *addr = data;
-}
-
-#define SPI_FLASH_CTL 0x00
-#define SPI_FLASH_OPCODE 0x04
-#define SPI_FLASH_DATA 0x08
-
-static __u8 spiflash_probe(void)
-{
- __u32 reg;
-
- do {
- reg = spiflash_regread32(SPI_FLASH_CTL);
- } while (reg & SPI_CTL_BUSY);
-
- spiflash_regwrite32(SPI_FLASH_OPCODE, 0xab);
-
- reg = (reg & ~SPI_CTL_TX_RX_CNT_MASK) | 4 |
- (1 << 4) | SPI_CTL_START;
-
- spiflash_regwrite32(SPI_FLASH_CTL, reg);
-
- do {
- reg = spiflash_regread32(SPI_FLASH_CTL);
- } while (reg & SPI_CTL_BUSY);
-
- reg = (__u32) spiflash_regread32(SPI_FLASH_DATA);
- reg &= 0xff;
-
- return (u8) reg;
-}
-
-
-#define STM_8MBIT_SIGNATURE 0x13
-#define STM_16MBIT_SIGNATURE 0x14
-#define STM_32MBIT_SIGNATURE 0x15
-#define STM_64MBIT_SIGNATURE 0x16
-#define STM_128MBIT_SIGNATURE 0x17
-
-
-static char __init *ar5315_flash_limit(void)
-{
- u8 sig;
- u32 flash_size = 0;
-
- /* probe the flash chip size */
- flash_regs = ioremap_nocache(ar5315_spiflash_res[1].start, ar5315_spiflash_res[1].end - ar5315_spiflash_res[1].start);
- sig = spiflash_probe();
- iounmap(flash_regs);
-
- switch(sig) {
- case STM_8MBIT_SIGNATURE:
- flash_size = 0x00100000;
- break;
- case STM_16MBIT_SIGNATURE:
- flash_size = 0x00200000;
- break;
- case STM_32MBIT_SIGNATURE:
- flash_size = 0x00400000;
- break;
- case STM_64MBIT_SIGNATURE:
- flash_size = 0x00800000;
- break;
- case STM_128MBIT_SIGNATURE:
- flash_size = 0x01000000;
- break;
- }
-
- ar5315_spiflash_res[0].end = ar5315_spiflash_res[0].start + flash_size;
- return (char *) ar5315_spiflash_res[0].end;
-}
-
-int __init ar5315_init_devices(void)
-{
- struct ar531x_config *config;
- struct ar531x_boarddata *bcfg;
- int dev = 0;
-#ifdef CONFIG_LEDS_GPIO
- int i;
- char *tmp;
-#endif
-
- if (!is_5315)
- return 0;
-
- /* Find board configuration */
- ar531x_find_config(ar5315_flash_limit());
- bcfg = (struct ar531x_boarddata *) board_config;
-
- config = (struct ar531x_config *) kzalloc(sizeof(struct ar531x_config), GFP_KERNEL);
- config->board = board_config;
- config->radio = radio_config;
- config->unit = 0;
- config->tag = (u_int16_t) (sysRegRead(AR5315_SREV) & AR5315_REV_CHIP);
-
- ar5315_eth_data.board_config = board_config;
- ar5315_eth_data.macaddr = bcfg->enet0Mac;
- ar5315_wmac.dev.platform_data = config;
-
- ar5315_devs[dev++] = &ar5315_eth;
- ar5315_devs[dev++] = &ar5315_wmac;
- ar5315_devs[dev++] = &ar5315_spiflash;
- ar5315_devs[dev++] = &ar5315_wdt;
-
-#ifdef CONFIG_LEDS_GPIO
- ar5315_led_data.num_leds = 0;
- for(i = 1; i < 8; i++)
- {
- if((i != AR5315_RESET_GPIO) && (i != bcfg->resetConfigGpio))
- {
- if(i == bcfg->sysLedGpio)
- {
- tmp = kstrdup("wlan", GFP_KERNEL);
- } else {
- tmp = kmalloc(6, GFP_KERNEL);
- if(tmp)
- sprintf((char*)tmp, "gpio%d", i);
- }
- if(tmp)
- {
- ar5315_leds[ar5315_led_data.num_leds].name = tmp;
- ar5315_leds[ar5315_led_data.num_leds].gpio = i;
- ar5315_leds[ar5315_led_data.num_leds].active_low = 0;
- ar5315_led_data.num_leds++;
- } else {
- printk("failed to alloc led string\n");
- continue;
- }
- }
- }
- ar5315_devs[dev++] = &ar5315_gpio_leds;
-#endif
-
- return platform_add_devices(ar5315_devs, dev);
-}
-
-static void ar5315_halt(void)
-{
- while (1);
-}
-
-static void ar5315_power_off(void)
-{
- ar5315_halt();
-}
-
-
-static void ar5315_restart(char *command)
-{
- void (*mips_reset_vec)(void) = (void *) 0xbfc00000;
-
- /* reset the system */
- sysRegWrite(AR5315_COLD_RESET,AR5317_RESET_SYSTEM);
-
- /* Cold reset does not work on the AR2315/6, use the GPIO reset bits a workaround.
- * give it some time to attempt a gpio based hardware reset
- * (atheros reference design workaround) */
- gpio_direction_output(AR5315_RESET_GPIO, 0);
- mdelay(100);
-
- /* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
- * workaround. Attempt to jump to the mips reset location -
- * the boot loader itself might be able to recover the system */
- mips_reset_vec();
-}
-
-
-/*
- * This table is indexed by bits 5..4 of the CLOCKCTL1 register
- * to determine the predevisor value.
- */
-static int __initdata CLOCKCTL1_PREDIVIDE_TABLE[4] = {
- 1,
- 2,
- 4,
- 5
-};
-
-static int __initdata PLLC_DIVIDE_TABLE[5] = {
- 2,
- 3,
- 4,
- 6,
- 3
-};
-
-static unsigned int __init
-ar5315_sys_clk(unsigned int clockCtl)
-{
- unsigned int pllcCtrl,cpuDiv;
- unsigned int pllcOut,refdiv,fdiv,divby2;
- unsigned int clkDiv;
-
- pllcCtrl = sysRegRead(AR5315_PLLC_CTL);
- refdiv = (pllcCtrl & PLLC_REF_DIV_M) >> PLLC_REF_DIV_S;
- refdiv = CLOCKCTL1_PREDIVIDE_TABLE[refdiv];
- fdiv = (pllcCtrl & PLLC_FDBACK_DIV_M) >> PLLC_FDBACK_DIV_S;
- divby2 = (pllcCtrl & PLLC_ADD_FDBACK_DIV_M) >> PLLC_ADD_FDBACK_DIV_S;
- divby2 += 1;
- pllcOut = (40000000/refdiv)*(2*divby2)*fdiv;
-
-
- /* clkm input selected */
- switch(clockCtl & CPUCLK_CLK_SEL_M) {
- case 0:
- case 1:
- clkDiv = PLLC_DIVIDE_TABLE[(pllcCtrl & PLLC_CLKM_DIV_M) >> PLLC_CLKM_DIV_S];
- break;
- case 2:
- clkDiv = PLLC_DIVIDE_TABLE[(pllcCtrl & PLLC_CLKC_DIV_M) >> PLLC_CLKC_DIV_S];
- break;
- default:
- pllcOut = 40000000;
- clkDiv = 1;
- break;
- }
- cpuDiv = (clockCtl & CPUCLK_CLK_DIV_M) >> CPUCLK_CLK_DIV_S;
- cpuDiv = cpuDiv * 2 ?: 1;
- return (pllcOut/(clkDiv * cpuDiv));
-}
-
-static inline unsigned int ar5315_cpu_frequency(void)
-{
- return ar5315_sys_clk(sysRegRead(AR5315_CPUCLK));
-}
-
-static inline unsigned int ar5315_apb_frequency(void)
-{
- return ar5315_sys_clk(sysRegRead(AR5315_AMBACLK));
-}
-
-static void __init ar5315_time_init(void)
-{
- mips_hpt_frequency = ar5315_cpu_frequency() / 2;
-}
-
-void __init ar5315_prom_init(void)
-{
- u32 memsize, memcfg, devid;
-
- is_5315 = 1;
- memcfg = sysRegRead(AR5315_MEM_CFG);
- memsize = 1 + ((memcfg & SDRAM_DATA_WIDTH_M) >> SDRAM_DATA_WIDTH_S);
- memsize <<= 1 + ((memcfg & SDRAM_COL_WIDTH_M) >> SDRAM_COL_WIDTH_S);
- memsize <<= 1 + ((memcfg & SDRAM_ROW_WIDTH_M) >> SDRAM_ROW_WIDTH_S);
- memsize <<= 3;
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-
- /* Detect the hardware based on the device ID */
- devid = sysRegRead(AR5315_SREV) & AR5315_REV_CHIP;
- switch(devid) {
- case 0x90:
- case 0x91:
- mips_machtype = MACH_ATHEROS_AR2317;
- break;
- default:
- mips_machtype = MACH_ATHEROS_AR2315;
- break;
- }
-}
-
-void __init ar5315_plat_setup(void)
-{
- unsigned int config = read_c0_config();
-
- /* Clear any lingering AHB errors */
- write_c0_config(config & ~0x3);
- sysRegWrite(AR5315_AHB_ERR0,AHB_ERROR_DET);
- sysRegRead(AR5315_AHB_ERR1);
- sysRegWrite(AR5315_WDC, WDC_IGNORE_EXPIRATION);
-
- board_time_init = ar5315_time_init;
-
- _machine_restart = ar5315_restart;
- _machine_halt = ar5315_halt;
- pm_power_off = ar5315_power_off;
-
- serial_setup(KSEG1ADDR(AR5315_UART0), ar5315_apb_frequency());
-}
-
-arch_initcall(ar5315_init_devices);
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-/*
- * Platform devices for Atheros SoCs
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-#include <linux/reboot.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <asm/bootinfo.h>
-#include <asm/irq_cpu.h>
-#include <asm/io.h>
-
-#include <ar531x.h>
-#include <gpio.h>
-
-static u32 gpiointmask = 0, gpiointval = 0;
-
-static inline void ar5315_gpio_irq(void)
-{
- u32 pend;
- sysRegWrite(AR5315_ISR, sysRegRead(AR5315_IMR) | ~AR5315_ISR_GPIO);
-
- /* only do one gpio interrupt at a time */
- pend = (sysRegRead(AR5315_GPIO_DI) ^ gpiointval) & gpiointmask;
- if (!pend)
- return;
-
- do_IRQ(AR531X_GPIO_IRQ_BASE + fls(pend) - 1);
-}
-
-
-/*
- * Called when an interrupt is received, this function
- * determines exactly which interrupt it was, and it
- * invokes the appropriate handler.
- *
- * Implicitly, we also define interrupt priority by
- * choosing which to dispatch first.
- */
-asmlinkage void ar5315_irq_dispatch(void)
-{
- int pending = read_c0_status() & read_c0_cause();
-
- if (pending & CAUSEF_IP3)
- do_IRQ(AR5315_IRQ_WLAN0_INTRS);
- else if (pending & CAUSEF_IP4)
- do_IRQ(AR5315_IRQ_ENET0_INTRS);
-#ifdef CONFIG_PCI
- else if (pending & CAUSEF_IP5)
- ar5315_pci_irq(AR5315_IRQ_LCBUS_PCI);
-#endif
- else if (pending & CAUSEF_IP2) {
- unsigned int ar531x_misc_intrs = sysRegRead(AR5315_ISR) & sysRegRead(AR5315_IMR);
-
- if (ar531x_misc_intrs & AR5315_ISR_SPI)
- do_IRQ(AR531X_MISC_IRQ_SPI);
- else if (ar531x_misc_intrs & AR5315_ISR_TIMER)
- do_IRQ(AR531X_MISC_IRQ_TIMER);
- else if (ar531x_misc_intrs & AR5315_ISR_AHB)
- do_IRQ(AR531X_MISC_IRQ_AHB_PROC);
- else if (ar531x_misc_intrs & AR5315_ISR_GPIO)
- ar5315_gpio_irq();
- else if (ar531x_misc_intrs & AR5315_ISR_UART0)
- do_IRQ(AR531X_MISC_IRQ_UART0);
- else if (ar531x_misc_intrs & AR5315_ISR_WD)
- do_IRQ(AR531X_MISC_IRQ_WATCHDOG);
- else
- do_IRQ(AR531X_MISC_IRQ_NONE);
- } else if (pending & CAUSEF_IP7)
- do_IRQ(AR531X_IRQ_CPU_CLOCK);
-}
-
-#ifdef CONFIG_PCI
-static inline void pci_abort_irq(void)
-{
- sysRegWrite(AR5315_PCI_INT_STATUS, AR5315_PCI_ABORT_INT);
- (void)sysRegRead(AR5315_PCI_INT_STATUS); /* flush write to hardware */
-}
-
-static inline void pci_ack_irq(void)
-{
- sysRegWrite(AR5315_PCI_INT_STATUS, AR5315_PCI_EXT_INT);
- (void)sysRegRead(AR5315_PCI_INT_STATUS); /* flush write to hardware */
-}
-
-void ar5315_pci_irq(int irq)
-{
- if (sysRegRead(AR5315_PCI_INT_STATUS) == AR5315_PCI_ABORT_INT)
- pci_abort_irq();
- else {
- do_IRQ(irq);
- pci_ack_irq();
- }
-}
-#endif
-
-static void ar5315_gpio_intr_enable(unsigned int irq)
-{
- u32 gpio, mask;
- gpio = irq - AR531X_GPIO_IRQ_BASE;
- mask = 1 << gpio;
- gpiointmask |= mask;
-
- /* reconfigure GPIO line as input */
- sysRegMask(AR5315_GPIO_CR, AR5315_GPIO_CR_M(gpio), AR5315_GPIO_CR_I(gpio));
-
- /* Enable interrupt with edge detection */
- sysRegMask(AR5315_GPIO_INT, AR5315_GPIO_INT_M | AR5315_GPIO_INT_LVL_M, gpio | AR5315_GPIO_INT_LVL(3));
-}
-
-static void ar5315_gpio_intr_disable(unsigned int irq)
-{
- u32 gpio, mask;
- gpio = irq - AR531X_GPIO_IRQ_BASE;
- mask = 1 << gpio;
-
- gpiointmask &= ~mask;
-
- /* Disable interrupt with edge detection */
- sysRegMask(AR5315_GPIO_INT, AR5315_GPIO_INT_M | AR5315_GPIO_INT_LVL_M, gpio | AR5315_GPIO_INT_LVL(0));
-}
-
-/* Turn on the specified AR531X_MISC_IRQ interrupt */
-static unsigned int ar5315_gpio_intr_startup(unsigned int irq)
-{
- ar5315_gpio_intr_enable(irq);
- return 0;
-}
-
-/* Turn off the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5315_gpio_intr_shutdown(unsigned int irq)
-{
- ar5315_gpio_intr_disable(irq);
-}
-
-static void
-ar5315_gpio_intr_ack(unsigned int irq)
-{
- ar5315_gpio_intr_disable(irq);
-}
-
-static void
-ar5315_gpio_intr_end(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- ar5315_gpio_intr_enable(irq);
-}
-
-static struct irq_chip ar5315_gpio_intr_controller = {
- .typename = "AR5315 GPIO",
- .startup = ar5315_gpio_intr_startup,
- .shutdown = ar5315_gpio_intr_shutdown,
- .enable = ar5315_gpio_intr_enable,
- .disable = ar5315_gpio_intr_disable,
- .ack = ar5315_gpio_intr_ack,
- .end = ar5315_gpio_intr_end,
-};
-
-
-/* Enable the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5315_misc_intr_enable(unsigned int irq)
-{
- unsigned int imr;
-
- imr = sysRegRead(AR5315_IMR);
- switch(irq)
- {
- case AR531X_MISC_IRQ_SPI:
- imr |= AR5315_ISR_SPI;
- break;
-
- case AR531X_MISC_IRQ_TIMER:
- imr |= AR5315_ISR_TIMER;
- break;
-
- case AR531X_MISC_IRQ_AHB_PROC:
- imr |= AR5315_ISR_AHB;
- break;
-
- case AR531X_MISC_IRQ_AHB_DMA:
- imr |= 0/* ?? */;
- break;
-
- case AR531X_MISC_IRQ_GPIO:
- imr |= AR5315_ISR_GPIO;
- break;
-
- case AR531X_MISC_IRQ_UART0:
- imr |= AR5315_ISR_UART0;
- break;
-
-
- case AR531X_MISC_IRQ_WATCHDOG:
- imr |= AR5315_ISR_WD;
- break;
-
- case AR531X_MISC_IRQ_LOCAL:
- imr |= 0/* ?? */;
- break;
-
- }
- sysRegWrite(AR5315_IMR, imr);
- imr=sysRegRead(AR5315_IMR); /* flush write buffer */
-}
-
-/* Disable the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5315_misc_intr_disable(unsigned int irq)
-{
- unsigned int imr;
-
- imr = sysRegRead(AR5315_IMR);
- switch(irq)
- {
- case AR531X_MISC_IRQ_SPI:
- imr &= ~AR5315_ISR_SPI;
- break;
-
- case AR531X_MISC_IRQ_TIMER:
- imr &= (~AR5315_ISR_TIMER);
- break;
-
- case AR531X_MISC_IRQ_AHB_PROC:
- imr &= (~AR5315_ISR_AHB);
- break;
-
- case AR531X_MISC_IRQ_AHB_DMA:
- imr &= 0/* ?? */;
- break;
-
- case AR531X_MISC_IRQ_GPIO:
- imr &= ~AR5315_ISR_GPIO;
- break;
-
- case AR531X_MISC_IRQ_UART0:
- imr &= (~AR5315_ISR_UART0);
- break;
-
- case AR531X_MISC_IRQ_WATCHDOG:
- imr &= (~AR5315_ISR_WD);
- break;
-
- case AR531X_MISC_IRQ_LOCAL:
- imr &= ~0/* ?? */;
- break;
-
- }
- sysRegWrite(AR5315_IMR, imr);
- sysRegRead(AR5315_IMR); /* flush write buffer */
-}
-
-/* Turn on the specified AR531X_MISC_IRQ interrupt */
-static unsigned int
-ar5315_misc_intr_startup(unsigned int irq)
-{
- ar5315_misc_intr_enable(irq);
- return 0;
-}
-
-/* Turn off the specified AR531X_MISC_IRQ interrupt */
-static void
-ar5315_misc_intr_shutdown(unsigned int irq)
-{
- ar5315_misc_intr_disable(irq);
-}
-
-static void
-ar5315_misc_intr_ack(unsigned int irq)
-{
- ar5315_misc_intr_disable(irq);
-}
-
-static void
-ar5315_misc_intr_end(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- ar5315_misc_intr_enable(irq);
-}
-
-static struct irq_chip ar5315_misc_intr_controller = {
- .typename = "AR5315 misc",
- .startup = ar5315_misc_intr_startup,
- .shutdown = ar5315_misc_intr_shutdown,
- .enable = ar5315_misc_intr_enable,
- .disable = ar5315_misc_intr_disable,
- .ack = ar5315_misc_intr_ack,
- .end = ar5315_misc_intr_end,
-};
-
-static irqreturn_t ar5315_ahb_proc_handler(int cpl, void *dev_id)
-{
- sysRegWrite(AR5315_AHB_ERR0,AHB_ERROR_DET);
- sysRegRead(AR5315_AHB_ERR1);
-
- printk("AHB fatal error\n");
- machine_restart("AHB error"); /* Catastrophic failure */
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction ar5315_ahb_proc_interrupt = {
- .handler = ar5315_ahb_proc_handler,
- .flags = IRQF_DISABLED,
- .name = "ar5315_ahb_proc_interrupt",
-};
-
-
-static struct irqaction cascade = {
- .handler = no_action,
- .flags = IRQF_DISABLED,
- .name = "cascade",
-};
-
-static void ar5315_gpio_intr_init(int irq_base)
-{
- int i;
-
- for (i = irq_base; i < irq_base + AR531X_GPIO_IRQ_COUNT; i++) {
- irq_desc[i].status = IRQ_DISABLED;
- irq_desc[i].action = NULL;
- irq_desc[i].depth = 1;
- irq_desc[i].chip = &ar5315_gpio_intr_controller;
- }
- setup_irq(AR531X_MISC_IRQ_GPIO, &cascade);
- gpiointval = sysRegRead(AR5315_GPIO_DI);
-}
-
-void ar5315_misc_intr_init(int irq_base)
-{
- int i;
-
- for (i = irq_base; i < irq_base + AR531X_MISC_IRQ_COUNT; i++) {
- irq_desc[i].status = IRQ_DISABLED;
- irq_desc[i].action = NULL;
- irq_desc[i].depth = 1;
- irq_desc[i].chip = &ar5315_misc_intr_controller;
- }
- setup_irq(AR531X_MISC_IRQ_AHB_PROC, &ar5315_ahb_proc_interrupt);
- setup_irq(AR5315_IRQ_MISC_INTRS, &cascade);
- ar5315_gpio_intr_init(AR531X_GPIO_IRQ_BASE);
-}
-
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/spinlock.h>
-#include <linux/delay.h>
-#include <linux/irq.h>
-#include <asm/bootinfo.h>
-#include <asm/paccess.h>
-#include <asm/irq_cpu.h>
-#include <asm/io.h>
-#include "ar531x.h"
-
-#define AR531X_MEM_BASE 0x80800000UL
-#define AR531X_MEM_SIZE 0x00ffffffUL
-#define AR531X_IO_SIZE 0x00007fffUL
-#define IDSEL_SHIFT 13
-
-static spinlock_t ar531x_pci_lock = SPIN_LOCK_UNLOCKED;
-static u32 cfgaddr;
-
-static int config_access(int busno, int dev, int func, int where, int size, u32 ptr, int write)
-{
- u32 address; /* Address to read from */
- u32 reg;
- unsigned long flags;
- int ret = -1;
- if ((busno != 0) || ((dev != 0) && (dev != 3)) || (func > 2))
- return ret;
-
- spin_lock_irqsave(&ar531x_pci_lock, flags);
-
- /* Select Configuration access */
- reg = sysRegRead(AR5315_PCI_MISC_CONFIG);
- reg |= AR5315_PCIMISC_CFG_SEL;
- sysRegWrite(AR5315_PCI_MISC_CONFIG, reg);
- (void)sysRegRead(AR5315_PCI_MISC_CONFIG);
-
- address = (u32)cfgaddr + (1 << (IDSEL_SHIFT + dev)) + (func << 8) + where;
-
- if (size == 1)
- address ^= 0x3;
- else if (size == 2)
- address ^= 0x2;
-
- if (write) {
- if (size == 1)
- ret = put_dbe(ptr, (u8 *) address);
- else if (size == 2)
- ret = put_dbe(ptr, (u16 *) address);
- else if (size == 4)
- ret = put_dbe(ptr, (u32 *) address);
- } else {
- if (size == 1)
- ret = get_dbe(*((u32 *)ptr), (u8 *) address);
- else if (size == 2)
- ret = get_dbe(*((u32 *)ptr), (u16 *) address);
- else if (size == 4)
- ret = get_dbe(*((u32 *)ptr), (u32 *) address);
- }
-
- /* Select Memory access */
- reg = sysRegRead(AR5315_PCI_MISC_CONFIG);
- reg &= ~AR5315_PCIMISC_CFG_SEL;
- sysRegWrite(AR5315_PCI_MISC_CONFIG, reg);
- (void)sysRegRead(AR5315_PCI_MISC_CONFIG);
-
- spin_unlock_irqrestore(&ar531x_pci_lock, flags);
-
- if (ret) {
- *((u32 *)ptr) = 0xffffffff;
- return PCIBIOS_DEVICE_NOT_FOUND;
- }
-
- return PCIBIOS_SUCCESSFUL;
-}
-
-static int ar531x_pci_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 * value)
-{
- return config_access(bus->number, PCI_SLOT(devfn), PCI_FUNC(devfn), where, size, (u32) value, 0);
-}
-
-static int ar531x_pci_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value)
-{
- return config_access(bus->number, PCI_SLOT(devfn), PCI_FUNC(devfn), where, size, value, 1);
-}
-
-struct pci_ops ar531x_pci_ops = {
- .read = ar531x_pci_read,
- .write = ar531x_pci_write,
-};
-
-static struct resource ar531x_mem_resource = {
- .name = "AR531x PCI MEM",
- .start = AR531X_MEM_BASE,
- .end = AR531X_MEM_BASE + AR531X_MEM_SIZE - AR531X_IO_SIZE - 1 + 0x4000000,
- .flags = IORESOURCE_MEM,
-};
-
-static struct resource ar531x_io_resource = {
- .name = "AR531x PCI I/O",
- .start = AR531X_MEM_BASE + AR531X_MEM_SIZE - AR531X_IO_SIZE,
- .end = AR531X_MEM_BASE + AR531X_MEM_SIZE - 1,
- .flags = IORESOURCE_IO,
-};
-
-struct pci_controller ar531x_pci_controller = {
- .pci_ops = &ar531x_pci_ops,
- .mem_resource = &ar531x_mem_resource,
- .io_resource = &ar531x_io_resource,
- .mem_offset = 0x00000000UL,
- .io_offset = 0x00000000UL,
-};
-
-int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- return AR5315_IRQ_LCBUS_PCI;
-}
-
-int pcibios_plat_dev_init(struct pci_dev *dev)
-{
- u32 reg;
-
- pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 5);
- pci_write_config_word(dev, 0x40, 0);
-
- /* Clear any pending Abort or external Interrupts
- * and enable interrupt processing */
- reg = sysRegRead(AR5315_PCI_INTEN_REG);
- reg &= ~AR5315_PCI_INT_ENABLE;
- sysRegWrite(AR5315_PCI_INTEN_REG, reg);
-
- reg = sysRegRead(AR5315_PCI_INT_STATUS);
- reg |= (AR5315_PCI_ABORT_INT | AR5315_PCI_EXT_INT);
- sysRegWrite(AR5315_PCI_INT_STATUS, reg);
-
- reg = sysRegRead(AR5315_PCI_INT_MASK);
- reg |= (AR5315_PCI_EXT_INT | AR5315_PCI_ABORT_INT);
- sysRegWrite(AR5315_PCI_INT_MASK, reg);
-
- reg = sysRegRead(AR5315_PCI_INTEN_REG);
- reg |= AR5315_PCI_INT_ENABLE;
- sysRegWrite(AR5315_PCI_INTEN_REG, reg);
-
- return 0;
-}
-
-static void ar5315_pci_fixup(struct pci_dev *dev)
-{
- struct pci_bus *bus = dev->bus;
-
- if ((PCI_SLOT(dev->devfn) != 3) || (PCI_FUNC(dev->devfn) != 0) || (bus->number != 0))
- return;
-
-#define _DEV bus->number, PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn)
- printk("PCI: fixing up device %d,%d,%d\n", _DEV);
- /* fix up mbars */
- config_access(_DEV, PCI_BASE_ADDRESS_0, 4, HOST_PCI_MBAR0, 1);
- config_access(_DEV, PCI_BASE_ADDRESS_1, 4, HOST_PCI_MBAR1, 1);
- config_access(_DEV, PCI_BASE_ADDRESS_2, 4, HOST_PCI_MBAR2, 1);
- config_access(_DEV, PCI_COMMAND, 4,
- PCI_COMMAND_MEMORY|PCI_COMMAND_MASTER|PCI_COMMAND_SPECIAL|
- PCI_COMMAND_INVALIDATE|PCI_COMMAND_PARITY|PCI_COMMAND_SERR|
- PCI_COMMAND_FAST_BACK, 1);
-#undef _DEV
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, ar5315_pci_fixup);
-
-int __init ar5315_pci_init(void)
-{
- u32 reg;
-
- if (mips_machtype != MACH_ATHEROS_AR2315)
- return -ENODEV;
-
- printk("AR531x PCI init... \n");
-
- cfgaddr = (u32) ioremap_nocache(0x80000000, 1*1024*1024); /* Remap PCI config space */
- ar531x_pci_controller.io_map_base =
- (unsigned long) ioremap_nocache(AR531X_MEM_BASE + AR531X_MEM_SIZE, AR531X_IO_SIZE);
- set_io_port_base(ar531x_pci_controller.io_map_base); /* PCI I/O space */
-
- reg = sysRegRead(AR5315_RESET);
- sysRegWrite(AR5315_RESET, reg | AR5315_RESET_PCIDMA);
-
- udelay(10*1000);
-
- sysRegWrite(AR5315_RESET, reg & ~AR5315_RESET_PCIDMA);
- sysRegRead(AR5315_RESET); /* read after */
-
- udelay(10*1000);
-
- reg = sysRegRead(AR5315_ENDIAN_CTL);
- reg |= AR5315_CONFIG_PCIAHB | AR5315_CONFIG_PCIAHB_BRIDGE;
-
- sysRegWrite(AR5315_ENDIAN_CTL, reg);
-
- reg = sysRegRead(AR5315_PCICLK);
- reg = 4;
- sysRegWrite(AR5315_PCICLK, reg);
-
- reg = sysRegRead(AR5315_AHB_ARB_CTL);
- reg |= (ARB_PCI);
- sysRegWrite(AR5315_AHB_ARB_CTL, reg);
-
- reg = sysRegRead(AR5315_IF_CTL);
- reg &= ~(IF_PCI_CLK_MASK | IF_MASK);
- reg |= (IF_PCI | IF_PCI_HOST | IF_PCI_INTR | (IF_PCI_CLK_OUTPUT_CLK << IF_PCI_CLK_SHIFT));
-
- sysRegWrite(AR5315_IF_CTL, reg);
-
- /* Reset the PCI bus by setting bits 5-4 in PCI_MCFG */
- reg = sysRegRead(AR5315_PCI_MISC_CONFIG);
- reg &= ~(AR5315_PCIMISC_RST_MODE);
- reg |= AR5315_PCIRST_LOW;
- sysRegWrite(AR5315_PCI_MISC_CONFIG, reg);
-
- /* wait for 100 ms */
- udelay(100*1000);
-
- /* Bring the PCI out of reset */
- reg = sysRegRead(AR5315_PCI_MISC_CONFIG);
- reg &= ~(AR5315_PCIMISC_RST_MODE);
- reg |= (AR5315_PCIRST_HIGH | AR5315_PCICACHE_DIS | 0x8);
- sysRegWrite(AR5315_PCI_MISC_CONFIG, reg);
-
- sysRegWrite(AR5315_PCI_UNCACHE_CFG,
- 0x1E | /* 1GB uncached */
- (1 << 5) | /* Enable uncached */
- (0x2 << 30) /* Base: 0x80000000 */
- );
- (void)sysRegRead(AR5315_PCI_UNCACHE_CFG); /* flush */
-
- udelay(500*1000);
-
- /* dirty hack - anyone with a datasheet that knows the memory map ? */
- ioport_resource.start = 0x10000000;
- ioport_resource.end = 0xffffffff;
- iomem_resource.start = 0x10000000;
- iomem_resource.end = 0xffffffff;
-
- register_pci_controller(&ar531x_pci_controller);
-
- printk("done\n");
- return 0;
-}
-
-arch_initcall(ar5315_pci_init);
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-/*
- * Platform devices for Atheros SoCs
- */
-
-#include <linux/autoconf.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/platform_device.h>
-#include <linux/kernel.h>
-#include <linux/serial.h>
-#include <linux/serial_core.h>
-#include <linux/random.h>
-#include <asm/bootinfo.h>
-#include <asm/irq_cpu.h>
-#include <asm/io.h>
-#include <ar531x.h>
-
-char *board_config = NULL;
-char *radio_config = NULL;
-int broken_boarddata = 0;
-
-extern int early_serial_setup(struct uart_port *port);
-
-static inline bool
-check_radio_magic(unsigned char *addr)
-{
- addr += 0x7a; /* offset for flash magic */
- if ((addr[0] == 0x5a) && (addr[1] == 0xa5)) {
- return 1;
- }
- return 0;
-}
-
-static inline bool
-check_board_data(unsigned char *flash_limit, unsigned char *addr, bool broken)
-{
- /* config magic found */
- if ( *(int *)addr == 0x35333131)
- return 1;
-
- if (!broken)
- return 0;
-
- if (check_radio_magic(addr + 0xf8))
- radio_config = addr + 0xf8;
- if ((addr < flash_limit + 0x10000) &&
- check_radio_magic(addr + 0x10000))
- radio_config = addr + 0x10000;
-
- if (radio_config) {
- /* broken board data detected, use radio data to find the offset,
- * user will fix this */
- broken_boarddata = 1;
- return 1;
- }
- return 0;
-}
-
-static u8 *find_board_config(char *flash_limit, bool broken)
-{
- char *addr;
- int found = 0;
-
- for (addr = (char *) (flash_limit - 0x1000);
- addr >= (char *) (flash_limit - 0x30000);
- addr -= 0x1000) {
-
- if (check_board_data(flash_limit, addr, broken)) {
- found = 1;
- break;
- }
- }
-
- if (!found)
- addr = NULL;
-
- return addr;
-}
-
-static u8 *find_radio_config(char *flash_limit, char *board_config)
-{
- int dataFound;
- char *radio_config;
-
- /*
- * Now find the start of Radio Configuration data, using heuristics:
- * Search forward from Board Configuration data by 0x1000 bytes
- * at a time until we find non-0xffffffff.
- */
- dataFound = 0;
- for (radio_config = board_config + 0x1000;
- (radio_config < flash_limit);
- radio_config += 0x1000) {
- if ((*(u32 *)radio_config != 0xffffffff) &&
- check_radio_magic(radio_config)) {
- dataFound = 1;
- break;
- }
- }
-
-#ifdef CONFIG_ATHEROS_AR5315
- if (!dataFound) { /* AR2316 relocates radio config to new location */
- for (radio_config = board_config + 0xf8;
- (radio_config < flash_limit - 0x1000 + 0xf8);
- radio_config += 0x1000) {
- if ((*(u32 *)radio_config != 0xffffffff) &&
- check_radio_magic(radio_config)) {
- dataFound = 1;
- break;
- }
- }
- }
-#endif
-
- if (!dataFound) {
- printk("Could not find Radio Configuration data\n");
- radio_config = 0;
- }
-
- return (u8 *) radio_config;
-}
-
-int __init ar531x_find_config(char *flash_limit)
-{
- struct ar531x_boarddata *bd;
- unsigned int rcfg_size;
- char *bcfg, *rcfg;
-
- /* Copy the board and radio data to RAM, because with the new
- * spiflash driver, accessing the mapped memory directly is no
- * longer safe */
-
- bcfg = find_board_config(flash_limit, false);
- if (!bcfg)
- bcfg = find_board_config(flash_limit, true);
- if (!bcfg) {
- printk("WARNING: No board configuration data found!\n");
- return -ENODEV;
- }
-
- board_config = kzalloc(BOARD_CONFIG_BUFSZ, GFP_KERNEL);
- memcpy(board_config, bcfg, 0x100);
- if (broken_boarddata) {
- printk("WARNING: broken board data detected\n");
- bd = (struct ar531x_boarddata *)board_config;
- if (!memcmp(bd->enet0Mac, "\x00\x00\x00\x00\x00\x00", 6)) {
- printk("Fixing up empty mac addresses\n");
- bd->enet0Mac[1] = 0x13;
- bd->enet0Mac[2] = 0x37;
- get_random_bytes(bd->enet0Mac + 3, 3);
- bd->wlan0Mac[1] = 0x13;
- bd->wlan0Mac[2] = 0x37;
- get_random_bytes(bd->wlan0Mac + 3, 3);
- }
- }
-
-
- /* Radio config starts 0x100 bytes after board config, regardless
- * of what the physical layout on the flash chip looks like */
-
- if (radio_config)
- rcfg = radio_config;
- else
- rcfg = find_radio_config(flash_limit, bcfg);
-
- if (!rcfg)
- return -ENODEV;
-
- radio_config = board_config + 0x100 + ((rcfg - bcfg) & 0xfff);
- printk("Radio config found at offset 0x%x(0x%x)\n", rcfg - bcfg, radio_config - board_config);
- rcfg_size = BOARD_CONFIG_BUFSZ - (radio_config - board_config);
- memcpy(radio_config, rcfg, rcfg_size);
-
- return 0;
-}
-
-void __init serial_setup(unsigned long mapbase, unsigned int uartclk)
-{
- struct uart_port s;
-
- memset(&s, 0, sizeof(s));
-
- s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST;
- s.iotype = UPIO_MEM;
- s.irq = AR531X_MISC_IRQ_UART0;
- s.regshift = 2;
- s.mapbase = mapbase;
- s.uartclk = uartclk;
- s.membase = (void __iomem *)s.mapbase;
-
- early_serial_setup(&s);
-}
-
-void __init plat_mem_setup(void)
-{
- DO_AR5312(ar5312_plat_setup();)
- DO_AR5315(ar5315_plat_setup();)
-
- /* Disable data watchpoints */
- write_c0_watchlo0(0);
-}
-
-const char *get_system_type(void)
-{
- switch (mips_machtype) {
-#ifdef CONFIG_ATHEROS_AR5312
- case MACH_ATHEROS_AR5312:
- return "Atheros AR5312";
-
- case MACH_ATHEROS_AR2312:
- return "Atheros AR2312";
-
- case MACH_ATHEROS_AR2313:
- return "Atheros AR2313";
-#endif
-#ifdef CONFIG_ATHEROS_AR5315
- case MACH_ATHEROS_AR2315:
- return "Atheros AR2315";
- case MACH_ATHEROS_AR2316:
- return "Atheros AR2316";
- case MACH_ATHEROS_AR2317:
- return "Atheros AR2317";
- case MACH_ATHEROS_AR2318:
- return "Atheros AR2318";
-#endif
- }
- return "Atheros (unknown)";
-}
-
-#if (LINUX_VERSION_CODE < KERNEL_VERSION(2,6,24))
-void __init plat_timer_setup(struct irqaction *irq)
-{
- unsigned int count;
-
- /* Usually irq is timer_irqaction (timer_interrupt) */
- setup_irq(AR531X_IRQ_CPU_CLOCK, irq);
-
- /* to generate the first CPU timer interrupt */
- count = read_c0_count();
- write_c0_compare(count + 1000);
-}
-#endif
-
-asmlinkage void plat_irq_dispatch(void)
-{
- DO_AR5312(ar5312_irq_dispatch();)
- DO_AR5315(ar5315_irq_dispatch();)
-}
-
-#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24))
-void (*board_time_init)(void);
-void __init plat_time_init(void) {
- board_time_init();
-}
-#endif
-
-void __init arch_init_irq(void)
-{
- clear_c0_status(ST0_IM);
- mips_cpu_irq_init();
-
- /* Initialize interrupt controllers */
- DO_AR5312(ar5312_misc_intr_init(AR531X_MISC_IRQ_BASE);)
- DO_AR5315(ar5315_misc_intr_init(AR531X_MISC_IRQ_BASE);)
-}
-
-static int __init ar531x_register_gpiodev(void)
-{
- static struct resource res = {
- .start = 0xFFFFFFFF,
- };
- struct platform_device *pdev;
-
- printk(KERN_INFO "ar531x: Registering GPIODEV device\n");
-
- pdev = platform_device_register_simple("GPIODEV", 0, &res, 1);
-
- if (!pdev) {
- printk(KERN_ERR "ar531x: GPIODEV init failed\n");
- return -ENODEV;
- }
-
- return 0;
-}
-
-device_initcall(ar531x_register_gpiodev);
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright MontaVista Software Inc
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-/*
- * Prom setup file for ar531x
- */
-
-#include <linux/init.h>
-#include <linux/autoconf.h>
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/mm.h>
-#include <linux/bootmem.h>
-
-#include <asm/bootinfo.h>
-#include <asm/addrspace.h>
-#include <ar531x.h>
-
-void __init prom_init(void)
-{
- char **argv;
-
- mips_machtype = -1;
-
- DO_AR5312(ar5312_prom_init();)
- DO_AR5315(ar5315_prom_init();)
-#if 0
- argv = (char **)fw_arg1;
- /* RedBoot desired command line is argv[1] */
- strcat(arcs_cmdline, argv[1]);
-#endif
-}
-
-void __init prom_free_prom_memory(void)
-{
-}
+++ /dev/null
-#include <linux/module.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/kobject.h>
-#include <linux/workqueue.h>
-#include <linux/skbuff.h>
-#include <linux/netlink.h>
-#include <net/sock.h>
-#include <asm/uaccess.h>
-#include <ar531x.h>
-
-#define AR531X_RESET_GPIO_IRQ (AR531X_GPIO_IRQ(bcfg->resetConfigGpio))
-
-struct event_t {
- struct work_struct wq;
- int set;
- unsigned long jiffies;
-};
-
-static struct ar531x_boarddata *bcfg;
-static struct timer_list rst_button_timer;
-
-extern struct sock *uevent_sock;
-extern u64 uevent_next_seqnum(void);
-static unsigned long seen;
-
-static inline void add_msg(struct sk_buff *skb, char *msg)
-{
- char *scratch;
- scratch = skb_put(skb, strlen(msg) + 1);
- sprintf(scratch, msg);
-}
-
-static void hotplug_button(struct work_struct *wq)
-{
- struct sk_buff *skb;
- struct event_t *event;
- size_t len;
- char *scratch, *s;
- char buf[128];
-
- event = container_of(wq, struct event_t, wq);
- if (!uevent_sock)
- goto done;
-
- /* allocate message with the maximum possible size */
- s = event->set ? "pressed" : "released";
- len = strlen(s) + 2;
- skb = alloc_skb(len + 2048, GFP_KERNEL);
- if (!skb)
- goto done;
-
- /* add header */
- scratch = skb_put(skb, len);
- sprintf(scratch, "%s@",s);
-
- /* copy keys to our continuous event payload buffer */
- add_msg(skb, "HOME=/");
- add_msg(skb, "PATH=/sbin:/bin:/usr/sbin:/usr/bin");
- add_msg(skb, "SUBSYSTEM=button");
- add_msg(skb, "BUTTON=reset");
- add_msg(skb, (event->set ? "ACTION=pressed" : "ACTION=released"));
- sprintf(buf, "SEEN=%ld", (event->jiffies - seen)/HZ);
- add_msg(skb, buf);
- snprintf(buf, 128, "SEQNUM=%llu", uevent_next_seqnum());
- add_msg(skb, buf);
-
- NETLINK_CB(skb).dst_group = 1;
- netlink_broadcast(uevent_sock, skb, 0, 1, GFP_KERNEL);
-
-done:
- kfree(event);
-}
-
-static int no_release_workaround = 1;
-
-static void
-reset_button_poll(unsigned long unused)
-{
- struct event_t *event;
- int gpio = ~0;
-
- if(!no_release_workaround)
- return;
-
- DO_AR5315(gpio = sysRegRead(AR5315_GPIO_DI);)
- gpio &= 1 << (AR531X_RESET_GPIO_IRQ - AR531X_GPIO_IRQ_BASE);
- if(gpio)
- {
- rst_button_timer.expires = jiffies + (HZ / 4);
- add_timer(&rst_button_timer);
- } else {
- event = (struct event_t *) kzalloc(sizeof(struct event_t), GFP_ATOMIC);
- if (!event)
- {
- printk("Could not alloc hotplug event\n");
- return;
- }
- event->set = 0;
- event->jiffies = jiffies;
- INIT_WORK(&event->wq, (void *)(void *)hotplug_button);
- schedule_work(&event->wq);
- }
-}
-
-static irqreturn_t button_handler(int irq, void *dev_id)
-{
- static int pressed = 0;
- struct event_t *event;
- u32 gpio = ~0;
-
- event = (struct event_t *) kzalloc(sizeof(struct event_t), GFP_ATOMIC);
- if (!event)
- return IRQ_NONE;
-
- pressed = !pressed;
-
- DO_AR5315(gpio = sysRegRead(AR5315_GPIO_DI);)
- gpio &= 1 << (irq - AR531X_GPIO_IRQ_BASE);
-
- event->set = gpio;
- if(!event->set)
- no_release_workaround = 0;
-
- event->jiffies = jiffies;
-
- INIT_WORK(&event->wq, (void *)(void *)hotplug_button);
- schedule_work(&event->wq);
-
- seen = jiffies;
- if(event->set && no_release_workaround)
- mod_timer(&rst_button_timer, jiffies + (HZ / 4));
-
- return IRQ_HANDLED;
-}
-
-void ar531x_disable_reset_button(void)
-{
- disable_irq(AR531X_RESET_GPIO_IRQ);
-}
-
-EXPORT_SYMBOL(ar531x_disable_reset_button);
-
-int __init ar531x_init_reset(void)
-{
- bcfg = (struct ar531x_boarddata *) board_config;
-
- seen = jiffies;
-
- init_timer(&rst_button_timer);
- rst_button_timer.function = reset_button_poll;
- rst_button_timer.expires = jiffies + HZ / 50;
- add_timer(&rst_button_timer);
-
- request_irq(AR531X_RESET_GPIO_IRQ, &button_handler, IRQF_SAMPLE_RANDOM, "ar531x_reset", NULL);
-
- return 0;
-}
-
-
-
-module_init(ar531x_init_reset);
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-#ifndef AR5312_H
-#define AR5312_H
-
-#include <asm/addrspace.h>
-
-/*
- * IRQs
- */
-
-#define AR5312_IRQ_WLAN0_INTRS MIPS_CPU_IRQ_BASE+2 /* C0_CAUSE: 0x0400 */
-#define AR5312_IRQ_ENET0_INTRS MIPS_CPU_IRQ_BASE+3 /* C0_CAUSE: 0x0800 */
-#define AR5312_IRQ_ENET1_INTRS MIPS_CPU_IRQ_BASE+4 /* C0_CAUSE: 0x1000 */
-#define AR5312_IRQ_WLAN1_INTRS MIPS_CPU_IRQ_BASE+5 /* C0_CAUSE: 0x2000 */
-#define AR5312_IRQ_MISC_INTRS MIPS_CPU_IRQ_BASE+6 /* C0_CAUSE: 0x4000 */
-
-
-/* Address Map */
-#define AR531X_WLAN0 0x18000000
-#define AR531X_WLAN1 0x18500000
-#define AR531X_ENET0 0x18100000
-#define AR531X_ENET1 0x18200000
-#define AR531X_SDRAMCTL 0x18300000
-#define AR531X_FLASHCTL 0x18400000
-#define AR531X_APBBASE 0x1c000000
-#define AR531X_FLASH 0x1e000000
-#define AR531X_UART0 0xbc000003 /* UART MMR */
-
-/*
- * AR531X_NUM_ENET_MAC defines the number of ethernet MACs that
- * should be considered available. The AR5312 supports 2 enet MACS,
- * even though many reference boards only actually use 1 of them
- * (i.e. Only MAC 0 is actually connected to an enet PHY or PHY switch.
- * The AR2312 supports 1 enet MAC.
- */
-#define AR531X_NUM_ENET_MAC 2
-
-/*
- * Need these defines to determine true number of ethernet MACs
- */
-#define AR5212_AR5312_REV2 0x0052 /* AR5312 WMAC (AP31) */
-#define AR5212_AR5312_REV7 0x0057 /* AR5312 WMAC (AP30-040) */
-#define AR5212_AR2313_REV8 0x0058 /* AR2313 WMAC (AP43-030) */
-#define AR531X_RADIO_MASK_OFF 0xc8
-#define AR531X_RADIO0_MASK 0x0003
-#define AR531X_RADIO1_MASK 0x000c
-#define AR531X_RADIO1_S 2
-
-/*
- * AR531X_NUM_WMAC defines the number of Wireless MACs that\
- * should be considered available.
- */
-#define AR531X_NUM_WMAC 2
-
-/* Reset/Timer Block Address Map */
-#define AR531X_RESETTMR (AR531X_APBBASE + 0x3000)
-#define AR531X_TIMER (AR531X_RESETTMR + 0x0000) /* countdown timer */
-#define AR531X_WD_CTRL (AR531X_RESETTMR + 0x0008) /* watchdog cntrl */
-#define AR531X_WD_TIMER (AR531X_RESETTMR + 0x000c) /* watchdog timer */
-#define AR531X_ISR (AR531X_RESETTMR + 0x0010) /* Intr Status Reg */
-#define AR531X_IMR (AR531X_RESETTMR + 0x0014) /* Intr Mask Reg */
-#define AR531X_RESET (AR531X_RESETTMR + 0x0020)
-#define AR5312_CLOCKCTL1 (AR531X_RESETTMR + 0x0064)
-#define AR5312_SCRATCH (AR531X_RESETTMR + 0x006c)
-#define AR531X_PROCADDR (AR531X_RESETTMR + 0x0070)
-#define AR531X_PROC1 (AR531X_RESETTMR + 0x0074)
-#define AR531X_DMAADDR (AR531X_RESETTMR + 0x0078)
-#define AR531X_DMA1 (AR531X_RESETTMR + 0x007c)
-#define AR531X_ENABLE (AR531X_RESETTMR + 0x0080) /* interface enb */
-#define AR531X_REV (AR531X_RESETTMR + 0x0090) /* revision */
-
-/* AR531X_WD_CTRL register bit field definitions */
-#define AR531X_WD_CTRL_IGNORE_EXPIRATION 0x0000
-#define AR531X_WD_CTRL_NMI 0x0001
-#define AR531X_WD_CTRL_RESET 0x0002
-
-/* AR531X_ISR register bit field definitions */
-#define AR531X_ISR_NONE 0x0000
-#define AR531X_ISR_TIMER 0x0001
-#define AR531X_ISR_AHBPROC 0x0002
-#define AR531X_ISR_AHBDMA 0x0004
-#define AR531X_ISR_GPIO 0x0008
-#define AR531X_ISR_UART0 0x0010
-#define AR531X_ISR_UART0DMA 0x0020
-#define AR531X_ISR_WD 0x0040
-#define AR531X_ISR_LOCAL 0x0080
-
-/* AR531X_RESET register bit field definitions */
-#define AR531X_RESET_SYSTEM 0x00000001 /* cold reset full system */
-#define AR531X_RESET_PROC 0x00000002 /* cold reset MIPS core */
-#define AR531X_RESET_WLAN0 0x00000004 /* cold reset WLAN MAC and BB */
-#define AR531X_RESET_EPHY0 0x00000008 /* cold reset ENET0 phy */
-#define AR531X_RESET_EPHY1 0x00000010 /* cold reset ENET1 phy */
-#define AR531X_RESET_ENET0 0x00000020 /* cold reset ENET0 mac */
-#define AR531X_RESET_ENET1 0x00000040 /* cold reset ENET1 mac */
-#define AR531X_RESET_UART0 0x00000100 /* cold reset UART0 (high speed) */
-#define AR531X_RESET_WLAN1 0x00000200 /* cold reset WLAN MAC/BB */
-#define AR531X_RESET_APB 0x00000400 /* cold reset APB (ar5312) */
-#define AR531X_RESET_WARM_PROC 0x00001000 /* warm reset MIPS core */
-#define AR531X_RESET_WARM_WLAN0_MAC 0x00002000 /* warm reset WLAN0 MAC */
-#define AR531X_RESET_WARM_WLAN0_BB 0x00004000 /* warm reset WLAN0 BaseBand */
-#define AR531X_RESET_NMI 0x00010000 /* send an NMI to the processor */
-#define AR531X_RESET_WARM_WLAN1_MAC 0x00020000 /* warm reset WLAN1 mac */
-#define AR531X_RESET_WARM_WLAN1_BB 0x00040000 /* warm reset WLAN1 baseband */
-#define AR531X_RESET_LOCAL_BUS 0x00080000 /* reset local bus */
-#define AR531X_RESET_WDOG 0x00100000 /* last reset was a watchdog */
-
-#define AR531X_RESET_WMAC0_BITS \
- AR531X_RESET_WLAN0 |\
- AR531X_RESET_WARM_WLAN0_MAC |\
- AR531X_RESET_WARM_WLAN0_BB
-
-#define AR531X_RESERT_WMAC1_BITS \
- AR531X_RESET_WLAN1 |\
- AR531X_RESET_WARM_WLAN1_MAC |\
- AR531X_RESET_WARM_WLAN1_BB
-
-/* AR5312_CLOCKCTL1 register bit field definitions */
-#define AR5312_CLOCKCTL1_PREDIVIDE_MASK 0x00000030
-#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT 4
-#define AR5312_CLOCKCTL1_MULTIPLIER_MASK 0x00001f00
-#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT 8
-#define AR5312_CLOCKCTL1_DOUBLER_MASK 0x00010000
-
-/* Valid for AR5312 and AR2312 */
-#define AR5312_CLOCKCTL1_PREDIVIDE_MASK 0x00000030
-#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT 4
-#define AR5312_CLOCKCTL1_MULTIPLIER_MASK 0x00001f00
-#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT 8
-#define AR5312_CLOCKCTL1_DOUBLER_MASK 0x00010000
-
-/* Valid for AR2313 */
-#define AR2313_CLOCKCTL1_PREDIVIDE_MASK 0x00003000
-#define AR2313_CLOCKCTL1_PREDIVIDE_SHIFT 12
-#define AR2313_CLOCKCTL1_MULTIPLIER_MASK 0x001f0000
-#define AR2313_CLOCKCTL1_MULTIPLIER_SHIFT 16
-#define AR2313_CLOCKCTL1_DOUBLER_MASK 0x00000000
-
-
-/* AR531X_ENABLE register bit field definitions */
-#define AR531X_ENABLE_WLAN0 0x0001
-#define AR531X_ENABLE_ENET0 0x0002
-#define AR531X_ENABLE_ENET1 0x0004
-#define AR531X_ENABLE_UART_AND_WLAN1_PIO 0x0008 /* UART, and WLAN1 PIOs */
-#define AR531X_ENABLE_WLAN1_DMA 0x0010 /* WLAN1 DMAs */
-#define AR531X_ENABLE_WLAN1 \
- (AR531X_ENABLE_UART_AND_WLAN1_PIO | AR531X_ENABLE_WLAN1_DMA)
-
-/* AR531X_REV register bit field definitions */
-#define AR531X_REV_WMAC_MAJ 0xf000
-#define AR531X_REV_WMAC_MAJ_S 12
-#define AR531X_REV_WMAC_MIN 0x0f00
-#define AR531X_REV_WMAC_MIN_S 8
-#define AR531X_REV_MAJ 0x00f0
-#define AR531X_REV_MAJ_S 4
-#define AR531X_REV_MIN 0x000f
-#define AR531X_REV_MIN_S 0
-#define AR531X_REV_CHIP (AR531X_REV_MAJ|AR531X_REV_MIN)
-
-/* Major revision numbers, bits 7..4 of Revision ID register */
-#define AR531X_REV_MAJ_AR5312 0x4
-#define AR531X_REV_MAJ_AR2313 0x5
-
-/* Minor revision numbers, bits 3..0 of Revision ID register */
-#define AR5312_REV_MIN_DUAL 0x0 /* Dual WLAN version */
-#define AR5312_REV_MIN_SINGLE 0x1 /* Single WLAN version */
-
-/* AR531X_FLASHCTL register bit field definitions */
-#define FLASHCTL_IDCY 0x0000000f /* Idle cycle turn around time */
-#define FLASHCTL_IDCY_S 0
-#define FLASHCTL_WST1 0x000003e0 /* Wait state 1 */
-#define FLASHCTL_WST1_S 5
-#define FLASHCTL_RBLE 0x00000400 /* Read byte lane enable */
-#define FLASHCTL_WST2 0x0000f800 /* Wait state 2 */
-#define FLASHCTL_WST2_S 11
-#define FLASHCTL_AC 0x00070000 /* Flash address check (added) */
-#define FLASHCTL_AC_S 16
-#define FLASHCTL_AC_128K 0x00000000
-#define FLASHCTL_AC_256K 0x00010000
-#define FLASHCTL_AC_512K 0x00020000
-#define FLASHCTL_AC_1M 0x00030000
-#define FLASHCTL_AC_2M 0x00040000
-#define FLASHCTL_AC_4M 0x00050000
-#define FLASHCTL_AC_8M 0x00060000
-#define FLASHCTL_AC_RES 0x00070000 /* 16MB is not supported */
-#define FLASHCTL_E 0x00080000 /* Flash bank enable (added) */
-#define FLASHCTL_BUSERR 0x01000000 /* Bus transfer error status flag */
-#define FLASHCTL_WPERR 0x02000000 /* Write protect error status flag */
-#define FLASHCTL_WP 0x04000000 /* Write protect */
-#define FLASHCTL_BM 0x08000000 /* Burst mode */
-#define FLASHCTL_MW 0x30000000 /* Memory width */
-#define FLASHCTL_MWx8 0x00000000 /* Memory width x8 */
-#define FLASHCTL_MWx16 0x10000000 /* Memory width x16 */
-#define FLASHCTL_MWx32 0x20000000 /* Memory width x32 (not supported) */
-#define FLASHCTL_ATNR 0x00000000 /* Access type == no retry */
-#define FLASHCTL_ATR 0x80000000 /* Access type == retry every */
-#define FLASHCTL_ATR4 0xc0000000 /* Access type == retry every 4 */
-
-/* ARM Flash Controller -- 3 flash banks with either x8 or x16 devices. */
-#define AR531X_FLASHCTL0 (AR531X_FLASHCTL + 0x00)
-#define AR531X_FLASHCTL1 (AR531X_FLASHCTL + 0x04)
-#define AR531X_FLASHCTL2 (AR531X_FLASHCTL + 0x08)
-
-/* ARM SDRAM Controller -- just enough to determine memory size */
-#define AR531X_MEM_CFG1 (AR531X_SDRAMCTL + 0x04)
-#define MEM_CFG1_AC0 0x00000700 /* bank 0: SDRAM addr check (added) */
-#define MEM_CFG1_AC0_S 8
-#define MEM_CFG1_AC1 0x00007000 /* bank 1: SDRAM addr check (added) */
-#define MEM_CFG1_AC1_S 12
-
-/* GPIO Address Map */
-#define AR531X_GPIO (AR531X_APBBASE + 0x2000)
-#define AR531X_GPIO_DO (AR531X_GPIO + 0x00) /* output register */
-#define AR531X_GPIO_DI (AR531X_GPIO + 0x04) /* intput register */
-#define AR531X_GPIO_CR (AR531X_GPIO + 0x08) /* control register */
-
-/* GPIO Control Register bit field definitions */
-#define AR531X_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
-#define AR531X_GPIO_CR_O(x) (0 << (x)) /* mask for output */
-#define AR531X_GPIO_CR_I(x) (1 << (x)) /* mask for input */
-#define AR531X_GPIO_CR_INT(x) (1 << ((x)+8)) /* mask for interrupt */
-#define AR531X_GPIO_CR_UART(x) (1 << ((x)+16)) /* uart multiplex */
-
-#endif
-
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
- */
-
-#ifndef AR5315_H
-#define AR5315_H
-
-/*
- * IRQs
- */
-#define AR5315_IRQ_MISC_INTRS MIPS_CPU_IRQ_BASE+2 /* C0_CAUSE: 0x0400 */
-#define AR5315_IRQ_WLAN0_INTRS MIPS_CPU_IRQ_BASE+3 /* C0_CAUSE: 0x0800 */
-#define AR5315_IRQ_ENET0_INTRS MIPS_CPU_IRQ_BASE+4 /* C0_CAUSE: 0x1000 */
-#define AR5315_IRQ_LCBUS_PCI MIPS_CPU_IRQ_BASE+5 /* C0_CAUSE: 0x2000 */
-#define AR5315_IRQ_WLAN0_POLL MIPS_CPU_IRQ_BASE+6 /* C0_CAUSE: 0x4000 */
-
-
-/*
- * Address map
- */
-#define AR5315_SDRAM0 0x00000000 /* DRAM */
-#define AR5315_SPI_READ 0x08000000 /* SPI FLASH */
-#define AR5315_WLAN0 0xB0000000 /* Wireless MMR */
-#define AR5315_PCI 0xB0100000 /* PCI MMR */
-#define AR5315_SDRAMCTL 0xB0300000 /* SDRAM MMR */
-#define AR5315_LOCAL 0xB0400000 /* LOCAL BUS MMR */
-#define AR5315_ENET0 0xB0500000 /* ETHERNET MMR */
-#define AR5315_DSLBASE 0xB1000000 /* RESET CONTROL MMR */
-#define AR5315_UART0 0xB1100003 /* UART MMR */
-#define AR5315_SPI 0xB1300000 /* SPI FLASH MMR */
-#define AR5315_FLASHBT 0xBfc00000 /* ro boot alias to FLASH */
-#define AR5315_RAM1 0x40000000 /* ram alias */
-#define AR5315_PCIEXT 0x80000000 /* pci external */
-#define AR5315_RAM2 0xc0000000 /* ram alias */
-#define AR5315_RAM3 0xe0000000 /* ram alias */
-
-/*
- * Reset Register
- */
-#define AR5315_COLD_RESET (AR5315_DSLBASE + 0x0000)
-
-/* Cold Reset */
-#define RESET_COLD_AHB 0x00000001
-#define RESET_COLD_APB 0x00000002
-#define RESET_COLD_CPU 0x00000004
-#define RESET_COLD_CPUWARM 0x00000008
-#define RESET_SYSTEM (RESET_COLD_CPU | RESET_COLD_APB | RESET_COLD_AHB) /* full system */
-
-#define AR5317_RESET_SYSTEM 0x00000010
-
-/* Warm Reset */
-
-#define AR5315_RESET (AR5315_DSLBASE + 0x0004)
-
-#define AR5315_RESET_WARM_WLAN0_MAC 0x00000001 /* warm reset WLAN0 MAC */
-#define AR5315_RESET_WARM_WLAN0_BB 0x00000002 /* warm reset WLAN0 BaseBand */
-#define AR5315_RESET_MPEGTS_RSVD 0x00000004 /* warm reset MPEG-TS */
-#define AR5315_RESET_PCIDMA 0x00000008 /* warm reset PCI ahb/dma */
-#define AR5315_RESET_MEMCTL 0x00000010 /* warm reset memory controller */
-#define AR5315_RESET_LOCAL 0x00000020 /* warm reset local bus */
-#define AR5315_RESET_I2C_RSVD 0x00000040 /* warm reset I2C bus */
-#define AR5315_RESET_SPI 0x00000080 /* warm reset SPI interface */
-#define AR5315_RESET_UART0 0x00000100 /* warm reset UART0 */
-#define AR5315_RESET_IR_RSVD 0x00000200 /* warm reset IR interface */
-#define AR5315_RESET_EPHY0 0x00000400 /* cold reset ENET0 phy */
-#define AR5315_RESET_ENET0 0x00000800 /* cold reset ENET0 mac */
-
-/*
- * AHB master arbitration control
- */
-#define AR5315_AHB_ARB_CTL (AR5315_DSLBASE + 0x0008)
-
-#define ARB_CPU 0x00000001 /* CPU, default */
-#define ARB_WLAN 0x00000002 /* WLAN */
-#define ARB_MPEGTS_RSVD 0x00000004 /* MPEG-TS */
-#define ARB_LOCAL 0x00000008 /* LOCAL */
-#define ARB_PCI 0x00000010 /* PCI */
-#define ARB_ETHERNET 0x00000020 /* Ethernet */
-#define ARB_RETRY 0x00000100 /* retry policy, debug only */
-
-/*
- * Config Register
- */
-#define AR5315_ENDIAN_CTL (AR5315_DSLBASE + 0x000c)
-
-#define AR5315_CONFIG_AHB 0x00000001 /* EC - AHB bridge endianess */
-#define AR5315_CONFIG_WLAN 0x00000002 /* WLAN byteswap */
-#define AR5315_CONFIG_MPEGTS_RSVD 0x00000004 /* MPEG-TS byteswap */
-#define AR5315_CONFIG_PCI 0x00000008 /* PCI byteswap */
-#define AR5315_CONFIG_MEMCTL 0x00000010 /* Memory controller endianess */
-#define AR5315_CONFIG_LOCAL 0x00000020 /* Local bus byteswap */
-#define AR5315_CONFIG_ETHERNET 0x00000040 /* Ethernet byteswap */
-
-#define AR5315_CONFIG_MERGE 0x00000200 /* CPU write buffer merge */
-#define AR5315_CONFIG_CPU 0x00000400 /* CPU big endian */
-#define AR5315_CONFIG_PCIAHB 0x00000800
-#define AR5315_CONFIG_PCIAHB_BRIDGE 0x00001000
-#define AR5315_CONFIG_SPI 0x00008000 /* SPI byteswap */
-#define AR5315_CONFIG_CPU_DRAM 0x00010000
-#define AR5315_CONFIG_CPU_PCI 0x00020000
-#define AR5315_CONFIG_CPU_MMR 0x00040000
-#define AR5315_CONFIG_BIG 0x00000400
-
-
-/*
- * NMI control
- */
-#define AR5315_NMI_CTL (AR5315_DSLBASE + 0x0010)
-
-#define NMI_EN 1
-
-/*
- * Revision Register - Initial value is 0x3010 (WMAC 3.0, AR531X 1.0).
- */
-#define AR5315_SREV (AR5315_DSLBASE + 0x0014)
-
-#define AR5315_REV_MAJ 0x00f0
-#define AR5315_REV_MAJ_S 4
-#define AR5315_REV_MIN 0x000f
-#define AR5315_REV_MIN_S 0
-#define AR5315_REV_CHIP (AR5315_REV_MAJ|AR5315_REV_MIN)
-
-/*
- * Interface Enable
- */
-#define AR5315_IF_CTL (AR5315_DSLBASE + 0x0018)
-
-#define IF_MASK 0x00000007
-#define IF_DISABLED 0
-#define IF_PCI 1
-#define IF_TS_LOCAL 2
-#define IF_ALL 3 /* only for emulation with separate pins */
-#define IF_LOCAL_HOST 0x00000008
-#define IF_PCI_HOST 0x00000010
-#define IF_PCI_INTR 0x00000020
-#define IF_PCI_CLK_MASK 0x00030000
-#define IF_PCI_CLK_INPUT 0
-#define IF_PCI_CLK_OUTPUT_LOW 1
-#define IF_PCI_CLK_OUTPUT_CLK 2
-#define IF_PCI_CLK_OUTPUT_HIGH 3
-#define IF_PCI_CLK_SHIFT 16
-
-
-/* Major revision numbers, bits 7..4 of Revision ID register */
-#define REV_MAJ_AR5311 0x01
-#define REV_MAJ_AR5312 0x04
-#define REV_MAJ_AR5315 0x0B
-
-/*
- * APB Interrupt control
- */
-
-#define AR5315_ISR (AR5315_DSLBASE + 0x0020)
-#define AR5315_IMR (AR5315_DSLBASE + 0x0024)
-#define AR5315_GISR (AR5315_DSLBASE + 0x0028)
-
-#define AR5315_ISR_UART0 0x0001 /* high speed UART */
-#define AR5315_ISR_I2C_RSVD 0x0002 /* I2C bus */
-#define AR5315_ISR_SPI 0x0004 /* SPI bus */
-#define AR5315_ISR_AHB 0x0008 /* AHB error */
-#define AR5315_ISR_APB 0x0010 /* APB error */
-#define AR5315_ISR_TIMER 0x0020 /* timer */
-#define AR5315_ISR_GPIO 0x0040 /* GPIO */
-#define AR5315_ISR_WD 0x0080 /* watchdog */
-#define AR5315_ISR_IR_RSVD 0x0100 /* IR */
-
-#define AR5315_GISR_MISC 0x0001
-#define AR5315_GISR_WLAN0 0x0002
-#define AR5315_GISR_MPEGTS_RSVD 0x0004
-#define AR5315_GISR_LOCALPCI 0x0008
-#define AR5315_GISR_WMACPOLL 0x0010
-#define AR5315_GISR_TIMER 0x0020
-#define AR5315_GISR_ETHERNET 0x0040
-
-/*
- * Interrupt routing from IO to the processor IP bits
- * Define our inter mask and level
- */
-#define AR5315_INTR_MISCIO SR_IBIT3
-#define AR5315_INTR_WLAN0 SR_IBIT4
-#define AR5315_INTR_ENET0 SR_IBIT5
-#define AR5315_INTR_LOCALPCI SR_IBIT6
-#define AR5315_INTR_WMACPOLL SR_IBIT7
-#define AR5315_INTR_COMPARE SR_IBIT8
-
-/*
- * Timers
- */
-#define AR5315_TIMER (AR5315_DSLBASE + 0x0030)
-#define AR5315_RELOAD (AR5315_DSLBASE + 0x0034)
-#define AR5315_WD (AR5315_DSLBASE + 0x0038)
-#define AR5315_WDC (AR5315_DSLBASE + 0x003c)
-
-#define WDC_RESET 0x00000002 /* reset on watchdog */
-#define WDC_NMI 0x00000001 /* NMI on watchdog */
-#define WDC_IGNORE_EXPIRATION 0x00000000
-
-/*
- * CPU Performance Counters
- */
-#define AR5315_PERFCNT0 (AR5315_DSLBASE + 0x0048)
-#define AR5315_PERFCNT1 (AR5315_DSLBASE + 0x004c)
-
-#define PERF_DATAHIT 0x0001 /* Count Data Cache Hits */
-#define PERF_DATAMISS 0x0002 /* Count Data Cache Misses */
-#define PERF_INSTHIT 0x0004 /* Count Instruction Cache Hits */
-#define PERF_INSTMISS 0x0008 /* Count Instruction Cache Misses */
-#define PERF_ACTIVE 0x0010 /* Count Active Processor Cycles */
-#define PERF_WBHIT 0x0020 /* Count CPU Write Buffer Hits */
-#define PERF_WBMISS 0x0040 /* Count CPU Write Buffer Misses */
-
-#define PERF_EB_ARDY 0x0001 /* Count EB_ARdy signal */
-#define PERF_EB_AVALID 0x0002 /* Count EB_AValid signal */
-#define PERF_EB_WDRDY 0x0004 /* Count EB_WDRdy signal */
-#define PERF_EB_RDVAL 0x0008 /* Count EB_RdVal signal */
-#define PERF_VRADDR 0x0010 /* Count valid read address cycles */
-#define PERF_VWADDR 0x0020 /* Count valid write address cycles */
-#define PERF_VWDATA 0x0040 /* Count valid write data cycles */
-
-/*
- * AHB Error Reporting.
- */
-#define AR5315_AHB_ERR0 (AR5315_DSLBASE + 0x0050) /* error */
-#define AR5315_AHB_ERR1 (AR5315_DSLBASE + 0x0054) /* haddr */
-#define AR5315_AHB_ERR2 (AR5315_DSLBASE + 0x0058) /* hwdata */
-#define AR5315_AHB_ERR3 (AR5315_DSLBASE + 0x005c) /* hrdata */
-#define AR5315_AHB_ERR4 (AR5315_DSLBASE + 0x0060) /* status */
-
-#define AHB_ERROR_DET 1 /* AHB Error has been detected, */
- /* write 1 to clear all bits in ERR0 */
-#define AHB_ERROR_OVR 2 /* AHB Error overflow has been detected */
-#define AHB_ERROR_WDT 4 /* AHB Error due to wdt instead of hresp */
-
-#define PROCERR_HMAST 0x0000000f
-#define PROCERR_HMAST_DFLT 0
-#define PROCERR_HMAST_WMAC 1
-#define PROCERR_HMAST_ENET 2
-#define PROCERR_HMAST_PCIENDPT 3
-#define PROCERR_HMAST_LOCAL 4
-#define PROCERR_HMAST_CPU 5
-#define PROCERR_HMAST_PCITGT 6
-
-#define PROCERR_HMAST_S 0
-#define PROCERR_HWRITE 0x00000010
-#define PROCERR_HSIZE 0x00000060
-#define PROCERR_HSIZE_S 5
-#define PROCERR_HTRANS 0x00000180
-#define PROCERR_HTRANS_S 7
-#define PROCERR_HBURST 0x00000e00
-#define PROCERR_HBURST_S 9
-
-
-
-/*
- * Clock Control
- */
-#define AR5315_PLLC_CTL (AR5315_DSLBASE + 0x0064)
-#define AR5315_PLLV_CTL (AR5315_DSLBASE + 0x0068)
-#define AR5315_CPUCLK (AR5315_DSLBASE + 0x006c)
-#define AR5315_AMBACLK (AR5315_DSLBASE + 0x0070)
-#define AR5315_SYNCCLK (AR5315_DSLBASE + 0x0074)
-#define AR5315_DSL_SLEEP_CTL (AR5315_DSLBASE + 0x0080)
-#define AR5315_DSL_SLEEP_DUR (AR5315_DSLBASE + 0x0084)
-
-/* PLLc Control fields */
-#define PLLC_REF_DIV_M 0x00000003
-#define PLLC_REF_DIV_S 0
-#define PLLC_FDBACK_DIV_M 0x0000007C
-#define PLLC_FDBACK_DIV_S 2
-#define PLLC_ADD_FDBACK_DIV_M 0x00000080
-#define PLLC_ADD_FDBACK_DIV_S 7
-#define PLLC_CLKC_DIV_M 0x0001c000
-#define PLLC_CLKC_DIV_S 14
-#define PLLC_CLKM_DIV_M 0x00700000
-#define PLLC_CLKM_DIV_S 20
-
-/* CPU CLK Control fields */
-#define CPUCLK_CLK_SEL_M 0x00000003
-#define CPUCLK_CLK_SEL_S 0
-#define CPUCLK_CLK_DIV_M 0x0000000c
-#define CPUCLK_CLK_DIV_S 2
-
-/* AMBA CLK Control fields */
-#define AMBACLK_CLK_SEL_M 0x00000003
-#define AMBACLK_CLK_SEL_S 0
-#define AMBACLK_CLK_DIV_M 0x0000000c
-#define AMBACLK_CLK_DIV_S 2
-
-#if defined(COBRA_EMUL)
-#define AR5315_AMBA_CLOCK_RATE 20000000
-#define AR5315_CPU_CLOCK_RATE 40000000
-#else
-#if defined(DEFAULT_PLL)
-#define AR5315_AMBA_CLOCK_RATE 40000000
-#define AR5315_CPU_CLOCK_RATE 40000000
-#else
-#define AR5315_AMBA_CLOCK_RATE 92000000
-#define AR5315_CPU_CLOCK_RATE 184000000
-#endif /* ! DEFAULT_PLL */
-#endif /* ! COBRA_EMUL */
-
-#define AR5315_UART_CLOCK_RATE AR5315_AMBA_CLOCK_RATE
-#define AR5315_SDRAM_CLOCK_RATE AR5315_AMBA_CLOCK_RATE
-
-/*
- * The UART computes baud rate as:
- * baud = clock / (16 * divisor)
- * where divisor is specified as a High Byte (DLM) and a Low Byte (DLL).
- */
-#define DESIRED_BAUD_RATE 38400
-
-
-#define CLOCKCTL_UART0 0x0010 /* enable UART0 external clock */
-
-
- /*
- * Applicable "PCICFG" bits for WLAN(s). Assoc status and LED mode.
- */
-#define ASSOC_STATUS_M 0x00000003
-#define ASSOC_STATUS_NONE 0
-#define ASSOC_STATUS_PENDING 1
-#define ASSOC_STATUS_ASSOCIATED 2
-#define LED_MODE_M 0x0000001c
-#define LED_BLINK_THRESHOLD_M 0x000000e0
-#define LED_SLOW_BLINK_MODE 0x00000100
-
-/*
- * GPIO
- */
-
-#define AR5315_GPIO_DI (AR5315_DSLBASE + 0x0088)
-#define AR5315_GPIO_DO (AR5315_DSLBASE + 0x0090)
-#define AR5315_GPIO_CR (AR5315_DSLBASE + 0x0098)
-#define AR5315_GPIO_INT (AR5315_DSLBASE + 0x00a0)
-
-#define AR5315_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
-#define AR5315_GPIO_CR_O(x) (1 << (x)) /* output */
-#define AR5315_GPIO_CR_I(x) (0) /* input */
-
-#define AR5315_GPIO_INT_S(x) (x) /* interrupt enable */
-#define AR5315_GPIO_INT_M (0x3F) /* mask for int */
-#define AR5315_GPIO_INT_LVL(x) ((x) << 6) /* interrupt level */
-#define AR5315_GPIO_INT_LVL_M ((0x3) << 6) /* mask for int level */
-
-#define AR5315_GPIO_INT_MAX_Y 1 /* Maximum value of Y for AR5313_GPIO_INT_* macros */
-#define AR5315_GPIO_INT_LVL_OFF 0 /* Triggerring off */
-#define AR5315_GPIO_INT_LVL_LOW 1 /* Low Level Triggered */
-#define AR5315_GPIO_INT_LVL_HIGH 2 /* High Level Triggered */
-#define AR5315_GPIO_INT_LVL_EDGE 3 /* Edge Triggered */
-
-#define AR5315_RESET_GPIO 5
-#define AR5315_NUM_GPIO 22
-
-
-/*
- * PCI Clock Control
- */
-
-#define AR5315_PCICLK (AR5315_DSLBASE + 0x00a4)
-
-#define AR5315_PCICLK_INPUT_M 0x3
-#define AR5315_PCICLK_INPUT_S 0
-
-#define AR5315_PCICLK_PLLC_CLKM 0
-#define AR5315_PCICLK_PLLC_CLKM1 1
-#define AR5315_PCICLK_PLLC_CLKC 2
-#define AR5315_PCICLK_REF_CLK 3
-
-#define AR5315_PCICLK_DIV_M 0xc
-#define AR5315_PCICLK_DIV_S 2
-
-#define AR5315_PCICLK_IN_FREQ 0
-#define AR5315_PCICLK_IN_FREQ_DIV_6 1
-#define AR5315_PCICLK_IN_FREQ_DIV_8 2
-#define AR5315_PCICLK_IN_FREQ_DIV_10 3
-
-/*
- * Observation Control Register
- */
-#define AR5315_OCR (AR5315_DSLBASE + 0x00b0)
-#define OCR_GPIO0_IRIN 0x0040
-#define OCR_GPIO1_IROUT 0x0080
-#define OCR_GPIO3_RXCLR 0x0200
-
-/*
- * General Clock Control
- */
-
-#define AR5315_MISCCLK (AR5315_DSLBASE + 0x00b4)
-#define MISCCLK_PLLBYPASS_EN 0x00000001
-#define MISCCLK_PROCREFCLK 0x00000002
-
-/*
- * SDRAM Controller
- * - No read or write buffers are included.
- */
-#define AR5315_MEM_CFG (AR5315_SDRAMCTL + 0x00)
-#define AR5315_MEM_CTRL (AR5315_SDRAMCTL + 0x0c)
-#define AR5315_MEM_REF (AR5315_SDRAMCTL + 0x10)
-
-#define SDRAM_DATA_WIDTH_M 0x00006000
-#define SDRAM_DATA_WIDTH_S 13
-
-#define SDRAM_COL_WIDTH_M 0x00001E00
-#define SDRAM_COL_WIDTH_S 9
-
-#define SDRAM_ROW_WIDTH_M 0x000001E0
-#define SDRAM_ROW_WIDTH_S 5
-
-#define SDRAM_BANKADDR_BITS_M 0x00000018
-#define SDRAM_BANKADDR_BITS_S 3
-
-/*
- * SPI Flash Interface Registers
- */
-
-#define AR5315_SPI_CTL (AR5315_SPI + 0x00)
-#define AR5315_SPI_OPCODE (AR5315_SPI + 0x04)
-#define AR5315_SPI_DATA (AR5315_SPI + 0x08)
-
-#define SPI_CTL_START 0x00000100
-#define SPI_CTL_BUSY 0x00010000
-#define SPI_CTL_TXCNT_MASK 0x0000000f
-#define SPI_CTL_RXCNT_MASK 0x000000f0
-#define SPI_CTL_TX_RX_CNT_MASK 0x000000ff
-#define SPI_CTL_SIZE_MASK 0x00060000
-
-#define SPI_CTL_CLK_SEL_MASK 0x03000000
-#define SPI_OPCODE_MASK 0x000000ff
-
-/*
- * PCI-MAC Configuration registers
- */
-#define PCI_MAC_RC (AR5315_PCI + 0x4000)
-#define PCI_MAC_SCR (AR5315_PCI + 0x4004)
-#define PCI_MAC_INTPEND (AR5315_PCI + 0x4008)
-#define PCI_MAC_SFR (AR5315_PCI + 0x400C)
-#define PCI_MAC_PCICFG (AR5315_PCI + 0x4010)
-#define PCI_MAC_SREV (AR5315_PCI + 0x4020)
-
-#define PCI_MAC_RC_MAC 0x00000001
-#define PCI_MAC_RC_BB 0x00000002
-
-#define PCI_MAC_SCR_SLMODE_M 0x00030000
-#define PCI_MAC_SCR_SLMODE_S 16
-#define PCI_MAC_SCR_SLM_FWAKE 0
-#define PCI_MAC_SCR_SLM_FSLEEP 1
-#define PCI_MAC_SCR_SLM_NORMAL 2
-
-#define PCI_MAC_SFR_SLEEP 0x00000001
-
-#define PCI_MAC_PCICFG_SPWR_DN 0x00010000
-
-
-/*
- * PCI Bus Interface Registers
- */
-#define AR5315_PCI_1MS_REG (AR5315_PCI + 0x0008)
-#define AR5315_PCI_1MS_MASK 0x3FFFF /* # of AHB clk cycles in 1ms */
-
-#define AR5315_PCI_MISC_CONFIG (AR5315_PCI + 0x000c)
-#define AR5315_PCIMISC_TXD_EN 0x00000001 /* Enable TXD for fragments */
-#define AR5315_PCIMISC_CFG_SEL 0x00000002 /* mem or config cycles */
-#define AR5315_PCIMISC_GIG_MASK 0x0000000C /* bits 31-30 for pci req */
-#define AR5315_PCIMISC_RST_MODE 0x00000030
-#define AR5315_PCIRST_INPUT 0x00000000 /* 4:5=0 rst is input */
-#define AR5315_PCIRST_LOW 0x00000010 /* 4:5=1 rst to GND */
-#define AR5315_PCIRST_HIGH 0x00000020 /* 4:5=2 rst to VDD */
-#define AR5315_PCIGRANT_EN 0x00000000 /* 6:7=0 early grant en */
-#define AR5315_PCIGRANT_FRAME 0x00000040 /* 6:7=1 grant waits 4 frame */
-#define AR5315_PCIGRANT_IDLE 0x00000080 /* 6:7=2 grant waits 4 idle */
-#define AR5315_PCIGRANT_GAP 0x00000000 /* 6:7=2 grant waits 4 idle */
-#define AR5315_PCICACHE_DIS 0x00001000 /* PCI external access cache disable */
-
-#define AR5315_PCI_OUT_TSTAMP (AR5315_PCI + 0x0010)
-
-#define AR5315_PCI_UNCACHE_CFG (AR5315_PCI + 0x0014)
-
-#define AR5315_PCI_IN_EN (AR5315_PCI + 0x0100)
-#define AR5315_PCI_IN_EN0 0x01 /* Enable chain 0 */
-#define AR5315_PCI_IN_EN1 0x02 /* Enable chain 1 */
-#define AR5315_PCI_IN_EN2 0x04 /* Enable chain 2 */
-#define AR5315_PCI_IN_EN3 0x08 /* Enable chain 3 */
-
-#define AR5315_PCI_IN_DIS (AR5315_PCI + 0x0104)
-#define AR5315_PCI_IN_DIS0 0x01 /* Disable chain 0 */
-#define AR5315_PCI_IN_DIS1 0x02 /* Disable chain 1 */
-#define AR5315_PCI_IN_DIS2 0x04 /* Disable chain 2 */
-#define AR5315_PCI_IN_DIS3 0x08 /* Disable chain 3 */
-
-#define AR5315_PCI_IN_PTR (AR5315_PCI + 0x0200)
-
-#define AR5315_PCI_OUT_EN (AR5315_PCI + 0x0400)
-#define AR5315_PCI_OUT_EN0 0x01 /* Enable chain 0 */
-
-#define AR5315_PCI_OUT_DIS (AR5315_PCI + 0x0404)
-#define AR5315_PCI_OUT_DIS0 0x01 /* Disable chain 0 */
-
-#define AR5315_PCI_OUT_PTR (AR5315_PCI + 0x0408)
-
-#define AR5315_PCI_INT_STATUS (AR5315_PCI + 0x0500) /* write one to clr */
-#define AR5315_PCI_TXINT 0x00000001 /* Desc In Completed */
-#define AR5315_PCI_TXOK 0x00000002 /* Desc In OK */
-#define AR5315_PCI_TXERR 0x00000004 /* Desc In ERR */
-#define AR5315_PCI_TXEOL 0x00000008 /* Desc In End-of-List */
-#define AR5315_PCI_RXINT 0x00000010 /* Desc Out Completed */
-#define AR5315_PCI_RXOK 0x00000020 /* Desc Out OK */
-#define AR5315_PCI_RXERR 0x00000040 /* Desc Out ERR */
-#define AR5315_PCI_RXEOL 0x00000080 /* Desc Out EOL */
-#define AR5315_PCI_TXOOD 0x00000200 /* Desc In Out-of-Desc */
-#define AR5315_PCI_MASK 0x0000FFFF /* Desc Mask */
-#define AR5315_PCI_EXT_INT 0x02000000
-#define AR5315_PCI_ABORT_INT 0x04000000
-
-#define AR5315_PCI_INT_MASK (AR5315_PCI + 0x0504) /* same as INT_STATUS */
-
-#define AR5315_PCI_INTEN_REG (AR5315_PCI + 0x0508)
-#define AR5315_PCI_INT_DISABLE 0x00 /* disable pci interrupts */
-#define AR5315_PCI_INT_ENABLE 0x01 /* enable pci interrupts */
-
-#define AR5315_PCI_HOST_IN_EN (AR5315_PCI + 0x0800)
-#define AR5315_PCI_HOST_IN_DIS (AR5315_PCI + 0x0804)
-#define AR5315_PCI_HOST_IN_PTR (AR5315_PCI + 0x0810)
-#define AR5315_PCI_HOST_OUT_EN (AR5315_PCI + 0x0900)
-#define AR5315_PCI_HOST_OUT_DIS (AR5315_PCI + 0x0904)
-#define AR5315_PCI_HOST_OUT_PTR (AR5315_PCI + 0x0908)
-
-
-/*
- * Local Bus Interface Registers
- */
-#define AR5315_LB_CONFIG (AR5315_LOCAL + 0x0000)
-#define AR5315_LBCONF_OE 0x00000001 /* =1 OE is low-true */
-#define AR5315_LBCONF_CS0 0x00000002 /* =1 first CS is low-true */
-#define AR5315_LBCONF_CS1 0x00000004 /* =1 2nd CS is low-true */
-#define AR5315_LBCONF_RDY 0x00000008 /* =1 RDY is low-true */
-#define AR5315_LBCONF_WE 0x00000010 /* =1 Write En is low-true */
-#define AR5315_LBCONF_WAIT 0x00000020 /* =1 WAIT is low-true */
-#define AR5315_LBCONF_ADS 0x00000040 /* =1 Adr Strobe is low-true */
-#define AR5315_LBCONF_MOT 0x00000080 /* =0 Intel, =1 Motorola */
-#define AR5315_LBCONF_8CS 0x00000100 /* =1 8 bits CS, 0= 16bits */
-#define AR5315_LBCONF_8DS 0x00000200 /* =1 8 bits Data S, 0=16bits */
-#define AR5315_LBCONF_ADS_EN 0x00000400 /* =1 Enable ADS */
-#define AR5315_LBCONF_ADR_OE 0x00000800 /* =1 Adr cap on OE, WE or DS */
-#define AR5315_LBCONF_ADDT_MUX 0x00001000 /* =1 Adr and Data share bus */
-#define AR5315_LBCONF_DATA_OE 0x00002000 /* =1 Data cap on OE, WE, DS */
-#define AR5315_LBCONF_16DATA 0x00004000 /* =1 Data is 16 bits wide */
-#define AR5315_LBCONF_SWAPDT 0x00008000 /* =1 Byte swap data */
-#define AR5315_LBCONF_SYNC 0x00010000 /* =1 Bus synchronous to clk */
-#define AR5315_LBCONF_INT 0x00020000 /* =1 Intr is low true */
-#define AR5315_LBCONF_INT_CTR0 0x00000000 /* GND high-Z, Vdd is high-Z */
-#define AR5315_LBCONF_INT_CTR1 0x00040000 /* GND drive, Vdd is high-Z */
-#define AR5315_LBCONF_INT_CTR2 0x00080000 /* GND high-Z, Vdd drive */
-#define AR5315_LBCONF_INT_CTR3 0x000C0000 /* GND drive, Vdd drive */
-#define AR5315_LBCONF_RDY_WAIT 0x00100000 /* =1 RDY is negative of WAIT */
-#define AR5315_LBCONF_INT_PULSE 0x00200000 /* =1 Interrupt is a pulse */
-#define AR5315_LBCONF_ENABLE 0x00400000 /* =1 Falcon respond to LB */
-
-#define AR5315_LB_CLKSEL (AR5315_LOCAL + 0x0004)
-#define AR5315_LBCLK_EXT 0x0001 /* use external clk for lb */
-
-#define AR5315_LB_1MS (AR5315_LOCAL + 0x0008)
-#define AR5315_LB1MS_MASK 0x3FFFF /* # of AHB clk cycles in 1ms */
-
-#define AR5315_LB_MISCCFG (AR5315_LOCAL + 0x000C)
-#define AR5315_LBM_TXD_EN 0x00000001 /* Enable TXD for fragments */
-#define AR5315_LBM_RX_INTEN 0x00000002 /* Enable LB ints on RX ready */
-#define AR5315_LBM_MBOXWR_INTEN 0x00000004 /* Enable LB ints on mbox wr */
-#define AR5315_LBM_MBOXRD_INTEN 0x00000008 /* Enable LB ints on mbox rd */
-#define AR5315_LMB_DESCSWAP_EN 0x00000010 /* Byte swap desc enable */
-#define AR5315_LBM_TIMEOUT_MASK 0x00FFFF80
-#define AR5315_LBM_TIMEOUT_SHFT 7
-#define AR5315_LBM_PORTMUX 0x07000000
-
-
-#define AR5315_LB_RXTSOFF (AR5315_LOCAL + 0x0010)
-
-#define AR5315_LB_TX_CHAIN_EN (AR5315_LOCAL + 0x0100)
-#define AR5315_LB_TXEN_0 0x01
-#define AR5315_LB_TXEN_1 0x02
-#define AR5315_LB_TXEN_2 0x04
-#define AR5315_LB_TXEN_3 0x08
-
-#define AR5315_LB_TX_CHAIN_DIS (AR5315_LOCAL + 0x0104)
-#define AR5315_LB_TX_DESC_PTR (AR5315_LOCAL + 0x0200)
-
-#define AR5315_LB_RX_CHAIN_EN (AR5315_LOCAL + 0x0400)
-#define AR5315_LB_RXEN 0x01
-
-#define AR5315_LB_RX_CHAIN_DIS (AR5315_LOCAL + 0x0404)
-#define AR5315_LB_RX_DESC_PTR (AR5315_LOCAL + 0x0408)
-
-#define AR5315_LB_INT_STATUS (AR5315_LOCAL + 0x0500)
-#define AR5315_INT_TX_DESC 0x0001
-#define AR5315_INT_TX_OK 0x0002
-#define AR5315_INT_TX_ERR 0x0004
-#define AR5315_INT_TX_EOF 0x0008
-#define AR5315_INT_RX_DESC 0x0010
-#define AR5315_INT_RX_OK 0x0020
-#define AR5315_INT_RX_ERR 0x0040
-#define AR5315_INT_RX_EOF 0x0080
-#define AR5315_INT_TX_TRUNC 0x0100
-#define AR5315_INT_TX_STARVE 0x0200
-#define AR5315_INT_LB_TIMEOUT 0x0400
-#define AR5315_INT_LB_ERR 0x0800
-#define AR5315_INT_MBOX_WR 0x1000
-#define AR5315_INT_MBOX_RD 0x2000
-
-/* Bit definitions for INT MASK are the same as INT_STATUS */
-#define AR5315_LB_INT_MASK (AR5315_LOCAL + 0x0504)
-
-#define AR5315_LB_INT_EN (AR5315_LOCAL + 0x0508)
-#define AR5315_LB_MBOX (AR5315_LOCAL + 0x0600)
-
-
-
-/*
- * IR Interface Registers
- */
-#define AR5315_IR_PKTDATA (AR5315_IR + 0x0000)
-
-#define AR5315_IR_PKTLEN (AR5315_IR + 0x07fc) /* 0 - 63 */
-
-#define AR5315_IR_CONTROL (AR5315_IR + 0x0800)
-#define AR5315_IRCTL_TX 0x00000000 /* use as tranmitter */
-#define AR5315_IRCTL_RX 0x00000001 /* use as receiver */
-#define AR5315_IRCTL_SAMPLECLK_MASK 0x00003ffe /* Sample clk divisor mask */
-#define AR5315_IRCTL_SAMPLECLK_SHFT 1
-#define AR5315_IRCTL_OUTPUTCLK_MASK 0x03ffc000 /* Output clk divisor mask */
-#define AR5315_IRCTL_OUTPUTCLK_SHFT 14
-
-#define AR5315_IR_STATUS (AR5315_IR + 0x0804)
-#define AR5315_IRSTS_RX 0x00000001 /* receive in progress */
-#define AR5315_IRSTS_TX 0x00000002 /* transmit in progress */
-
-#define AR5315_IR_CONFIG (AR5315_IR + 0x0808)
-#define AR5315_IRCFG_INVIN 0x00000001 /* invert input polarity */
-#define AR5315_IRCFG_INVOUT 0x00000002 /* invert output polarity */
-#define AR5315_IRCFG_SEQ_START_WIN_SEL 0x00000004 /* 1 => 28, 0 => 7 */
-#define AR5315_IRCFG_SEQ_START_THRESH 0x000000f0 /* */
-#define AR5315_IRCFG_SEQ_END_UNIT_SEL 0x00000100 /* */
-#define AR5315_IRCFG_SEQ_END_UNIT_THRESH 0x00007e00 /* */
-#define AR5315_IRCFG_SEQ_END_WIN_SEL 0x00008000 /* */
-#define AR5315_IRCFG_SEQ_END_WIN_THRESH 0x001f0000 /* */
-#define AR5315_IRCFG_NUM_BACKOFF_WORDS 0x01e00000 /* */
-
-/*
- * PCI memory constants: Memory area 1 and 2 are the same size -
- * (twice the PCI_TLB_PAGE_SIZE). The definition of
- * CPU_TO_PCI_MEM_SIZE is coupled with the TLB setup routine
- * sysLib.c/sysTlbInit(), in that it assumes that 2 pages of size
- * PCI_TLB_PAGE_SIZE are set up in the TLB for each PCI memory space.
- */
-
-#define CPU_TO_PCI_MEM_BASE1 0xE0000000
-#define CPU_TO_PCI_MEM_SIZE1 (2*PCI_TLB_PAGE_SIZE)
-
-
-/* TLB attributes for PCI transactions */
-
-#define PCI_MMU_PAGEMASK 0x00003FFF
-#define MMU_PAGE_UNCACHED 0x00000010
-#define MMU_PAGE_DIRTY 0x00000004
-#define MMU_PAGE_VALID 0x00000002
-#define MMU_PAGE_GLOBAL 0x00000001
-#define PCI_MMU_PAGEATTRIB (MMU_PAGE_UNCACHED|MMU_PAGE_DIRTY|\
- MMU_PAGE_VALID|MMU_PAGE_GLOBAL)
-#define PCI_MEMORY_SPACE1_VIRT 0xE0000000 /* Used for non-prefet mem */
-#define PCI_MEMORY_SPACE1_PHYS 0x80000000
-#define PCI_TLB_PAGE_SIZE 0x01000000
-#define TLB_HI_MASK 0xFFFFE000
-#define TLB_LO_MASK 0x3FFFFFFF
-#define PAGEMASK_SHIFT 11
-#define TLB_LO_SHIFT 6
-
-#define PCI_MAX_LATENCY 0xFFF /* Max PCI latency */
-
-#define HOST_PCI_DEV_ID 3
-#define HOST_PCI_MBAR0 0x10000000
-#define HOST_PCI_MBAR1 0x20000000
-#define HOST_PCI_MBAR2 0x30000000
-
-#define HOST_PCI_SDRAM_BASEADDR HOST_PCI_MBAR1
-#define PCI_DEVICE_MEM_SPACE 0x800000
-
-#endif
-
+++ /dev/null
-#ifndef __AR531X_H
-#define __AR531X_H
-
-#include <linux/version.h>
-#include <asm/cpu-info.h>
-#include <ar531x_platform.h>
-#include <ar5312/ar5312.h>
-#include <ar5315/ar5315.h>
-
-#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24))
-extern void (*board_time_init)(void);
-#endif
-
-/*
- * Atheros CPUs before the AR2315 are using MIPS 4Kc core, later designs are
- * using MIPS 4KEc R2 core. This makes it easy to determine the board at runtime.
- */
-#ifdef CONFIG_ATHEROS_AR5312
-#define DO_AR5312(...) \
- if (current_cpu_data.cputype != CPU_4KEC) { \
- __VA_ARGS__ \
- }
-#else
-#define DO_AR5312(...)
-#endif
-#ifdef CONFIG_ATHEROS_AR5315
-#define DO_AR5315(...) \
- if (current_cpu_data.cputype == CPU_4KEC) { \
- __VA_ARGS__ \
- }
-#else
-#define DO_AR5315(...)
-#endif
-
-#define AR531X_MISC_IRQ_BASE 0x20
-#define AR531X_GPIO_IRQ_BASE 0x30
-
-/* Software's idea of interrupts handled by "CPU Interrupt Controller" */
-#define AR531X_IRQ_NONE MIPS_CPU_IRQ_BASE+0
-#define AR531X_IRQ_CPU_CLOCK MIPS_CPU_IRQ_BASE+7 /* C0_CAUSE: 0x8000 */
-
-/* Miscellaneous interrupts, which share IP6 */
-#define AR531X_MISC_IRQ_NONE AR531X_MISC_IRQ_BASE+0
-#define AR531X_MISC_IRQ_TIMER AR531X_MISC_IRQ_BASE+1
-#define AR531X_MISC_IRQ_AHB_PROC AR531X_MISC_IRQ_BASE+2
-#define AR531X_MISC_IRQ_AHB_DMA AR531X_MISC_IRQ_BASE+3
-#define AR531X_MISC_IRQ_GPIO AR531X_MISC_IRQ_BASE+4
-#define AR531X_MISC_IRQ_UART0 AR531X_MISC_IRQ_BASE+5
-#define AR531X_MISC_IRQ_UART0_DMA AR531X_MISC_IRQ_BASE+6
-#define AR531X_MISC_IRQ_WATCHDOG AR531X_MISC_IRQ_BASE+7
-#define AR531X_MISC_IRQ_LOCAL AR531X_MISC_IRQ_BASE+8
-#define AR531X_MISC_IRQ_SPI AR531X_MISC_IRQ_BASE+9
-#define AR531X_MISC_IRQ_COUNT 10
-
-/* GPIO Interrupts [0..7], share AR531X_MISC_IRQ_GPIO */
-#define AR531X_GPIO_IRQ_NONE AR531X_GPIO_IRQ_BASE+0
-#define AR531X_GPIO_IRQ(n) AR531X_GPIO_IRQ_BASE+n
-#define AR531X_GPIO_IRQ_COUNT 22
-
-#define sysRegRead(phys) \
- (*(volatile u32 *)KSEG1ADDR(phys))
-
-#define sysRegWrite(phys, val) \
- ((*(volatile u32 *)KSEG1ADDR(phys)) = (val))
-
-/*
- * This is board-specific data that is stored in a "fixed" location in flash.
- * It is shared across operating systems, so it should not be changed lightly.
- * The main reason we need it is in order to extract the ethernet MAC
- * address(es).
- */
-struct ar531x_boarddata {
- u32 magic; /* board data is valid */
-#define AR531X_BD_MAGIC 0x35333131 /* "5311", for all 531x platforms */
- u16 cksum; /* checksum (starting with BD_REV 2) */
- u16 rev; /* revision of this struct */
-#define BD_REV 4
- char boardName[64]; /* Name of board */
- u16 major; /* Board major number */
- u16 minor; /* Board minor number */
- u32 config; /* Board configuration */
-#define BD_ENET0 0x00000001 /* ENET0 is stuffed */
-#define BD_ENET1 0x00000002 /* ENET1 is stuffed */
-#define BD_UART1 0x00000004 /* UART1 is stuffed */
-#define BD_UART0 0x00000008 /* UART0 is stuffed (dma) */
-#define BD_RSTFACTORY 0x00000010 /* Reset factory defaults stuffed */
-#define BD_SYSLED 0x00000020 /* System LED stuffed */
-#define BD_EXTUARTCLK 0x00000040 /* External UART clock */
-#define BD_CPUFREQ 0x00000080 /* cpu freq is valid in nvram */
-#define BD_SYSFREQ 0x00000100 /* sys freq is set in nvram */
-#define BD_WLAN0 0x00000200 /* Enable WLAN0 */
-#define BD_MEMCAP 0x00000400 /* CAP SDRAM @ memCap for testing */
-#define BD_DISWATCHDOG 0x00000800 /* disable system watchdog */
-#define BD_WLAN1 0x00001000 /* Enable WLAN1 (ar5212) */
-#define BD_ISCASPER 0x00002000 /* FLAG for AR2312 */
-#define BD_WLAN0_2G_EN 0x00004000 /* FLAG for radio0_2G */
-#define BD_WLAN0_5G_EN 0x00008000 /* FLAG for radio0_2G */
-#define BD_WLAN1_2G_EN 0x00020000 /* FLAG for radio0_2G */
-#define BD_WLAN1_5G_EN 0x00040000 /* FLAG for radio0_2G */
- u16 resetConfigGpio; /* Reset factory GPIO pin */
- u16 sysLedGpio; /* System LED GPIO pin */
-
- u32 cpuFreq; /* CPU core frequency in Hz */
- u32 sysFreq; /* System frequency in Hz */
- u32 cntFreq; /* Calculated C0_COUNT frequency */
-
- u8 wlan0Mac[6];
- u8 enet0Mac[6];
- u8 enet1Mac[6];
-
- u16 pciId; /* Pseudo PCIID for common code */
- u16 memCap; /* cap bank1 in MB */
-
- /* version 3 */
- u8 wlan1Mac[6]; /* (ar5212) */
-};
-
-#define BOARD_CONFIG_BUFSZ 0x1000
-
-extern char *board_config, *radio_config;
-extern void serial_setup(unsigned long mapbase, unsigned int uartclk);
-extern int ar531x_find_config(char *flash_limit);
-
-extern void ar5312_prom_init(void);
-extern void ar5312_misc_intr_init(int irq_base);
-extern void ar5312_plat_setup(void);
-extern asmlinkage void ar5312_irq_dispatch(void);
-
-extern void ar5315_prom_init(void);
-extern void ar5315_misc_intr_init(int irq_base);
-extern void ar5315_plat_setup(void);
-extern asmlinkage void ar5315_irq_dispatch(void);
-extern void ar5315_pci_irq(int irq);
-static inline u32 sysRegMask(u32 phys, u32 mask, u32 value)
-{
- u32 reg;
-
- reg = sysRegRead(phys);
- reg &= ~mask;
- reg |= value & mask;
- sysRegWrite(phys, reg);
- reg = sysRegRead(phys); /* flush write to the hardware */
-
- return reg;
-}
-
-#define AR531X_NUM_GPIO 8
-
-#endif
+++ /dev/null
-#ifndef __AR531X_PLATFORM_H
-#define __AR531X_PLATFORM_H
-
-/*
- * Board support data. The driver is required to locate
- * and fill-in this information before passing a reference to
- * this structure as the HAL_BUS_TAG parameter supplied to
- * ath_hal_attach.
- */
-struct ar531x_config {
- const char *board; /* board config data */
- const char *radio; /* radio config data */
- int unit; /* unit number [0, 1] */
- u32 tag; /* used as devid for now */
-};
-
-struct ar531x_eth {
- int phy;
- int mac;
- u32 reset_base;
- u32 reset_mac;
- u32 reset_phy;
- u32 phy_base;
- char *board_config;
- char *macaddr;
-};
-
-#endif /* __AR531X_PLATFORM_H */
+++ /dev/null
-/*
- * Atheros SoC specific CPU feature overrides
- *
- * Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This file was derived from: include/asm-mips/cpu-features.h
- * Copyright (C) 2003, 2004 Ralf Baechle
- * Copyright (C) 2004 Maciej W. Rozycki
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- */
-#ifndef __ASM_MACH_ATHEROS_CPU_FEATURE_OVERRIDES_H
-#define __ASM_MACH_ATHEROS_CPU_FEATURE_OVERRIDES_H
-
-/*
- * The ATHEROS SoCs have MIPS 4Kc/4KEc core.
- */
-#define cpu_has_tlb 1
-#define cpu_has_4kex 1
-#define cpu_has_3k_cache 0
-#define cpu_has_4k_cache 1
-#define cpu_has_tx39_cache 0
-#define cpu_has_sb1_cache 0
-#define cpu_has_fpu 0
-#define cpu_has_32fpr 0
-#define cpu_has_counter 1
-/* #define cpu_has_watch ? */
-/* #define cpu_has_divec ? */
-/* #define cpu_has_vce ? */
-/* #define cpu_has_cache_cdex_p ? */
-/* #define cpu_has_cache_cdex_s ? */
-/* #define cpu_has_prefetch ? */
-/* #define cpu_has_mcheck ? */
-#define cpu_has_ejtag 1
-
-#if !defined(CONFIG_ATHEROS_AR5312)
-# define cpu_has_llsc 1
-#else
-/*
- * The MIPS 4Kc V0.9 core in the AR5312/AR2312 have problems with the
- * ll/sc instructions.
- */
-# define cpu_has_llsc 0
-#endif
-
-#define cpu_has_mips16 0
-#define cpu_has_mdmx 0
-#define cpu_has_mips3d 0
-#define cpu_has_smartmips 0
-
-/* #define cpu_has_vtag_icache ? */
-/* #define cpu_has_dc_aliases ? */
-/* #define cpu_has_ic_fills_f_dc ? */
-/* #define cpu_has_pindexed_dcache ? */
-
-/* #define cpu_icache_snoops_remote_store ? */
-
-#define cpu_has_mips32r1 1
-
-#if !defined(CONFIG_ATHEROS_AR5312)
-# define cpu_has_mips32r2 1
-#endif
-
-#define cpu_has_mips64r1 0
-#define cpu_has_mips64r2 0
-
-#define cpu_has_dsp 0
-#define cpu_has_mipsmt 0
-
-/* #define cpu_has_nofpuex ? */
-#define cpu_has_64bits 0
-#define cpu_has_64bit_zero_reg 0
-#define cpu_has_64bit_gp_regs 0
-#define cpu_has_64bit_addresses 0
-
-/* #define cpu_has_inclusive_pcaches ? */
-
-/* #define cpu_dcache_line_size() ? */
-/* #define cpu_icache_line_size() ? */
-
-#endif /* __ASM_MACH_ATHEROS_CPU_FEATURE_OVERRIDES_H */
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2006 Ralf Baechle <ralf@linux-mips.org>
- * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
- *
- */
-#ifndef __ASM_MACH_GENERIC_DMA_COHERENCE_H
-#define __ASM_MACH_GENERIC_DMA_COHERENCE_H
-
-#define PCI_DMA_OFFSET 0x20000000
-
-struct device;
-
-static dma_addr_t plat_map_dma_mem(struct device *dev, void *addr, size_t size)
-{
- return virt_to_phys(addr) + (dev != NULL ? PCI_DMA_OFFSET : 0);
-}
-
-static dma_addr_t plat_map_dma_mem_page(struct device *dev, struct page *page)
-{
- return page_to_phys(page) + (dev != NULL ? PCI_DMA_OFFSET : 0);
-}
-
-static unsigned long plat_dma_addr_to_phys(dma_addr_t dma_addr)
-{
- return (dma_addr > PCI_DMA_OFFSET ? dma_addr - PCI_DMA_OFFSET : dma_addr);
-}
-
-static void plat_unmap_dma_mem(dma_addr_t dma_addr)
-{
-}
-
-static inline int plat_device_is_coherent(struct device *dev)
-{
- return 0;
-}
-
-#endif /* __ASM_MACH_GENERIC_DMA_COHERENCE_H */
+++ /dev/null
-#ifndef _ATHEROS_GPIO_H_
-#define _ATHEROS_GPIO_H_
-
-#include "ar531x.h"
-
-/* Common AR531X global variables */
-/* extern u32 ar531x_gpio_intr_Mask; */
-
-/* AR5312 exported routines */
-#ifdef CONFIG_ATHEROS_AR5312
-asmlinkage void ar5312_gpio_irq_dispatch(void);
-#endif
-
-/* AR5315 exported routines */
-#ifdef CONFIG_ATHEROS_AR5315
-asmlinkage void ar5315_gpio_irq_dispatch(void);
-#endif
-
-/*
- * Wrappers for the generic GPIO layer
- */
-
-/* Sets a gpio to input, or returns ENXIO for non-existent gpio */
-static inline int gpio_direction_input(unsigned gpio) {
- DO_AR5312( if (gpio > AR531X_NUM_GPIO) { \
- return -ENXIO; \
- } else { \
- sysRegWrite(AR531X_GPIO_CR, \
- sysRegRead(AR531X_GPIO_CR) | \
- AR531X_GPIO_CR_I(gpio) ); \
- return 0; \
- } \
- )
- DO_AR5315( if (gpio > AR5315_NUM_GPIO) { \
- return -ENXIO; \
- } else { \
- sysRegWrite(AR5315_GPIO_CR, \
- ( sysRegRead(AR5315_GPIO_CR) & \
- ~(AR5315_GPIO_CR_M(gpio)) ) | \
- AR5315_GPIO_CR_I(gpio) ); \
- return 0; \
- } \
- )
- return -ENXIO;
-}
-
-/* Sets a gpio to output with value, or returns ENXIO for non-existent gpio */
-static inline int gpio_direction_output(unsigned gpio, int value) {
- DO_AR5312( if (gpio > AR531X_NUM_GPIO) { \
- return -ENXIO; \
- } else { \
- sysRegWrite(AR531X_GPIO_DO, \
- ( (sysRegRead(AR531X_GPIO_DO) & \
- ~(1 << gpio) ) | \
- ((value!=0) << gpio)) ); \
- sysRegWrite(AR531X_GPIO_CR, \
- ( sysRegRead(AR531X_GPIO_CR) & \
- ~(AR531X_GPIO_CR_M(gpio)) )); \
- return 0; \
- } \
- )
- DO_AR5315( if (gpio > AR5315_NUM_GPIO) { \
- return -ENXIO; \
- } else { \
- sysRegWrite(AR5315_GPIO_DO, \
- ( (sysRegRead(AR5315_GPIO_DO) & \
- ~(1 << gpio)) | \
- ((value!=0) << gpio)) ); \
- sysRegWrite(AR5315_GPIO_CR, \
- sysRegRead(AR5315_GPIO_CR) | \
- AR5315_GPIO_CR_O(gpio) ); \
- return 0; \
- } \
- )
- return -ENXIO;
-}
-
-/* Reads the gpio pin. Unchecked function */
-static inline int gpio_get_value(unsigned gpio) {
- DO_AR5312(return (sysRegRead(AR531X_GPIO_DI) & (1 << gpio));)
- DO_AR5315(return (sysRegRead(AR5315_GPIO_DI) & (1 << gpio));)
- return 0;
-}
-
-/* Writes to the gpio pin. Unchecked function */
-static inline void gpio_set_value(unsigned gpio, int value) {
- DO_AR5312( sysRegWrite(AR531X_GPIO_DO, \
- ( (sysRegRead(AR531X_GPIO_DO) & \
- ~(1 << gpio)) | \
- ((value!=0) << gpio)) ); \
- )
- DO_AR5315( sysRegWrite(AR5315_GPIO_DO, \
- ( (sysRegRead(AR5315_GPIO_DO) & \
- ~(1 << gpio)) | \
- ((value!=0) << gpio)) ); \
- )
-}
-
-static inline int gpio_request(unsigned gpio, const char *label) {
- return 0;
-}
-
-static inline void gpio_free(unsigned gpio) {
-}
-
-/* Returns IRQ to attach for gpio. Unchecked function */
-static inline int gpio_to_irq(unsigned gpio) {
- return AR531X_GPIO_IRQ(gpio);
-}
-
-/* Returns gpio for IRQ attached. Unchecked function */
-static inline int irq_to_gpio(unsigned irq) {
- return (irq - (AR531X_GPIO_IRQ(0)));
-}
-
-#include <asm-generic/gpio.h> /* cansleep wrappers */
-
-#endif
+++ /dev/null
-#ifndef __AR531X_RESET_H
-#define __AR531X_RESET_H
-
-void ar531x_disable_reset_button(void);
-
-#endif /* __AR531X_RESET_H */
+++ /dev/null
-/*
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
- * Copyright (C) 2008 Felix Fietkau <nbd@openwrt.org>
- */
-#ifndef __ASM_MIPS_MACH_ATHEROS_WAR_H
-#define __ASM_MIPS_MACH_ATHEROS_WAR_H
-
-#define R4600_V1_INDEX_ICACHEOP_WAR 0
-#define R4600_V1_HIT_CACHEOP_WAR 0
-#define R4600_V2_HIT_CACHEOP_WAR 0
-#define R5432_CP0_INTERRUPT_WAR 0
-#define BCM1250_M3_WAR 0
-#define SIBYTE_1956_WAR 0
-#define MIPS4K_ICACHE_REFILL_WAR 0
-#define MIPS_CACHE_SYNC_WAR 0
-#define TX49XX_ICACHE_INDEX_INV_WAR 0
-#define RM9000_CDEX_SMP_WAR 0
-#define ICACHE_REFILLS_WORKAROUND_WAR 0
-#define R10000_LLSC_WAR 0
-#define MIPS34K_MISSED_ITLB_WAR 0
-
-#endif /* __ASM_MIPS_MACH_ATHEROS_WAR_H */
+++ /dev/null
-
-/*
- * MTD driver for the SPI Flash Memory support.
- *
- * Copyright (c) 2005-2006 Atheros Communications Inc.
- * Copyright (C) 2006-2007 FON Technology, SL.
- * Copyright (C) 2006-2007 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006-2007 Felix Fietkau <nbd@openwrt.org>
- *
- * This code is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-/*===========================================================================
-** !!!! VERY IMPORTANT NOTICE !!!! FLASH DATA STORED IN LITTLE ENDIAN FORMAT
-**
-** This module contains the Serial Flash access routines for the Atheros SOC.
-** The Atheros SOC integrates a SPI flash controller that is used to access
-** serial flash parts. The SPI flash controller executes in "Little Endian"
-** mode. THEREFORE, all WRITES and READS from the MIPS CPU must be
-** BYTESWAPPED! The SPI Flash controller hardware by default performs READ
-** ONLY byteswapping when accessed via the SPI Flash Alias memory region
-** (Physical Address 0x0800_0000 - 0x0fff_ffff). The data stored in the
-** flash sectors is stored in "Little Endian" format.
-**
-** The spiflash_write() routine performs byteswapping on all write
-** operations.
-**===========================================================================*/
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/version.h>
-#include <linux/errno.h>
-#include <linux/slab.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/squashfs_fs.h>
-#include <linux/root_dev.h>
-#include <linux/delay.h>
-#include <asm/delay.h>
-#include <asm/io.h>
-#include "spiflash.h"
-
-#ifndef __BIG_ENDIAN
-#error This driver currently only works with big endian CPU.
-#endif
-
-#define MAX_PARTS 32
-
-#define SPIFLASH "spiflash: "
-
-#define MIN(a,b) ((a) < (b) ? (a) : (b))
-
-#define busy_wait(condition, wait) \
- do { \
- while (condition) { \
- spin_unlock_bh(&spidata->mutex); \
- if (wait > 1) \
- msleep(wait); \
- else if ((wait == 1) && need_resched()) \
- schedule(); \
- else \
- udelay(1); \
- spin_lock_bh(&spidata->mutex); \
- } \
- } while (0)
-
-
-static __u32 spiflash_regread32(int reg);
-static void spiflash_regwrite32(int reg, __u32 data);
-static __u32 spiflash_sendcmd (int op, u32 addr);
-
-int __init spiflash_init (void);
-void __exit spiflash_exit (void);
-static int spiflash_probe_chip (void);
-static int spiflash_erase (struct mtd_info *mtd,struct erase_info *instr);
-static int spiflash_read (struct mtd_info *mtd, loff_t from,size_t len,size_t *retlen,u_char *buf);
-static int spiflash_write (struct mtd_info *mtd,loff_t to,size_t len,size_t *retlen,const u_char *buf);
-
-/* Flash configuration table */
-struct flashconfig {
- __u32 byte_cnt;
- __u32 sector_cnt;
- __u32 sector_size;
- __u32 cs_addrmask;
-} flashconfig_tbl[MAX_FLASH] =
- {
- { 0, 0, 0, 0},
- { STM_1MB_BYTE_COUNT, STM_1MB_SECTOR_COUNT, STM_1MB_SECTOR_SIZE, 0x0},
- { STM_2MB_BYTE_COUNT, STM_2MB_SECTOR_COUNT, STM_2MB_SECTOR_SIZE, 0x0},
- { STM_4MB_BYTE_COUNT, STM_4MB_SECTOR_COUNT, STM_4MB_SECTOR_SIZE, 0x0},
- { STM_8MB_BYTE_COUNT, STM_8MB_SECTOR_COUNT, STM_8MB_SECTOR_SIZE, 0x0},
- { STM_16MB_BYTE_COUNT, STM_16MB_SECTOR_COUNT, STM_16MB_SECTOR_SIZE, 0x0}
- };
-
-/* Mapping of generic opcodes to STM serial flash opcodes */
-#define SPI_WRITE_ENABLE 0
-#define SPI_WRITE_DISABLE 1
-#define SPI_RD_STATUS 2
-#define SPI_WR_STATUS 3
-#define SPI_RD_DATA 4
-#define SPI_FAST_RD_DATA 5
-#define SPI_PAGE_PROGRAM 6
-#define SPI_SECTOR_ERASE 7
-#define SPI_BULK_ERASE 8
-#define SPI_DEEP_PWRDOWN 9
-#define SPI_RD_SIG 10
-#define SPI_MAX_OPCODES 11
-
-struct opcodes {
- __u16 code;
- __s8 tx_cnt;
- __s8 rx_cnt;
-} stm_opcodes[] = {
- {STM_OP_WR_ENABLE, 1, 0},
- {STM_OP_WR_DISABLE, 1, 0},
- {STM_OP_RD_STATUS, 1, 1},
- {STM_OP_WR_STATUS, 1, 0},
- {STM_OP_RD_DATA, 4, 4},
- {STM_OP_FAST_RD_DATA, 5, 0},
- {STM_OP_PAGE_PGRM, 8, 0},
- {STM_OP_SECTOR_ERASE, 4, 0},
- {STM_OP_BULK_ERASE, 1, 0},
- {STM_OP_DEEP_PWRDOWN, 1, 0},
- {STM_OP_RD_SIG, 4, 1},
-};
-
-/* Driver private data structure */
-struct spiflash_data {
- struct mtd_info *mtd;
- struct mtd_partition *parsed_parts; /* parsed partitions */
- void *readaddr; /* memory mapped data for read */
- void *mmraddr; /* memory mapped register space */
- wait_queue_head_t wq;
- spinlock_t mutex;
- int state;
-};
-enum {
- FL_READY,
- FL_READING,
- FL_ERASING,
- FL_WRITING
-};
-
-static struct spiflash_data *spidata;
-
-extern int parse_redboot_partitions(struct mtd_info *master, struct mtd_partition **pparts);
-
-/***************************************************************************************************/
-
-static __u32
-spiflash_regread32(int reg)
-{
- volatile __u32 *data = (__u32 *)(spidata->mmraddr + reg);
-
- return (*data);
-}
-
-static void
-spiflash_regwrite32(int reg, __u32 data)
-{
- volatile __u32 *addr = (__u32 *)(spidata->mmraddr + reg);
-
- *addr = data;
- return;
-}
-
-
-static __u32
-spiflash_sendcmd (int op, u32 addr)
-{
- u32 reg;
- u32 mask;
- struct opcodes *ptr_opcode;
-
- ptr_opcode = &stm_opcodes[op];
- busy_wait((reg = spiflash_regread32(SPI_FLASH_CTL)) & SPI_CTL_BUSY, 0);
- spiflash_regwrite32(SPI_FLASH_OPCODE, ((u32) ptr_opcode->code) | (addr << 8));
-
- reg = (reg & ~SPI_CTL_TX_RX_CNT_MASK) | ptr_opcode->tx_cnt |
- (ptr_opcode->rx_cnt << 4) | SPI_CTL_START;
-
- spiflash_regwrite32(SPI_FLASH_CTL, reg);
- busy_wait(spiflash_regread32(SPI_FLASH_CTL) & SPI_CTL_BUSY, 0);
-
- if (!ptr_opcode->rx_cnt)
- return 0;
-
- reg = (__u32) spiflash_regread32(SPI_FLASH_DATA);
-
- switch (ptr_opcode->rx_cnt) {
- case 1:
- mask = 0x000000ff;
- break;
- case 2:
- mask = 0x0000ffff;
- break;
- case 3:
- mask = 0x00ffffff;
- break;
- default:
- mask = 0xffffffff;
- break;
- }
- reg &= mask;
-
- return reg;
-}
-
-
-
-/* Probe SPI flash device
- * Function returns 0 for failure.
- * and flashconfig_tbl array index for success.
- */
-static int
-spiflash_probe_chip (void)
-{
- __u32 sig;
- int flash_size;
-
- /* Read the signature on the flash device */
- spin_lock_bh(&spidata->mutex);
- sig = spiflash_sendcmd(SPI_RD_SIG, 0);
- spin_unlock_bh(&spidata->mutex);
-
- switch (sig) {
- case STM_8MBIT_SIGNATURE:
- flash_size = FLASH_1MB;
- break;
- case STM_16MBIT_SIGNATURE:
- flash_size = FLASH_2MB;
- break;
- case STM_32MBIT_SIGNATURE:
- flash_size = FLASH_4MB;
- break;
- case STM_64MBIT_SIGNATURE:
- flash_size = FLASH_8MB;
- break;
- case STM_128MBIT_SIGNATURE:
- flash_size = FLASH_16MB;
- break;
- default:
- printk (KERN_WARNING SPIFLASH "Read of flash device signature failed!\n");
- return (0);
- }
-
- return (flash_size);
-}
-
-
-/* wait until the flash chip is ready and grab a lock */
-static int spiflash_wait_ready(int state)
-{
- DECLARE_WAITQUEUE(wait, current);
-
-retry:
- spin_lock_bh(&spidata->mutex);
- if (spidata->state != FL_READY) {
- set_current_state(TASK_UNINTERRUPTIBLE);
- add_wait_queue(&spidata->wq, &wait);
- spin_unlock_bh(&spidata->mutex);
- schedule();
- remove_wait_queue(&spidata->wq, &wait);
-
- if(signal_pending(current))
- return 0;
-
- goto retry;
- }
- spidata->state = state;
-
- return 1;
-}
-
-static inline void spiflash_done(void)
-{
- spidata->state = FL_READY;
- spin_unlock_bh(&spidata->mutex);
- wake_up(&spidata->wq);
-}
-
-static int
-spiflash_erase (struct mtd_info *mtd,struct erase_info *instr)
-{
- struct opcodes *ptr_opcode;
- u32 temp, reg;
-
- /* sanity checks */
- if (instr->addr + instr->len > mtd->size) return (-EINVAL);
-
- if (!spiflash_wait_ready(FL_ERASING))
- return -EINTR;
-
- spiflash_sendcmd(SPI_WRITE_ENABLE, 0);
- busy_wait((reg = spiflash_regread32(SPI_FLASH_CTL)) & SPI_CTL_BUSY, 0);
- reg = spiflash_regread32(SPI_FLASH_CTL);
-
- ptr_opcode = &stm_opcodes[SPI_SECTOR_ERASE];
- temp = ((__u32)instr->addr << 8) | (__u32)(ptr_opcode->code);
- spiflash_regwrite32(SPI_FLASH_OPCODE, temp);
-
- reg = (reg & ~SPI_CTL_TX_RX_CNT_MASK) | ptr_opcode->tx_cnt | SPI_CTL_START;
- spiflash_regwrite32(SPI_FLASH_CTL, reg);
-
- /* this will take some time */
- spin_unlock_bh(&spidata->mutex);
- msleep(800);
- spin_lock_bh(&spidata->mutex);
-
- busy_wait(spiflash_sendcmd(SPI_RD_STATUS, 0) & SPI_STATUS_WIP, 20);
- spiflash_done();
-
- instr->state = MTD_ERASE_DONE;
- if (instr->callback) instr->callback (instr);
-
- return 0;
-}
-
-static int
-spiflash_read (struct mtd_info *mtd, loff_t from,size_t len,size_t *retlen,u_char *buf)
-{
- u8 *read_addr;
-
- /* sanity checks */
- if (!len) return (0);
- if (from + len > mtd->size) return (-EINVAL);
-
- /* we always read len bytes */
- *retlen = len;
-
- if (!spiflash_wait_ready(FL_READING))
- return -EINTR;
- read_addr = (u8 *)(spidata->readaddr + from);
- memcpy(buf, read_addr, len);
- spiflash_done();
-
- return 0;
-}
-
-static int
-spiflash_write (struct mtd_info *mtd,loff_t to,size_t len,size_t *retlen,const u_char *buf)
-{
- u32 opcode, bytes_left;
-
- *retlen = 0;
-
- /* sanity checks */
- if (!len) return (0);
- if (to + len > mtd->size) return (-EINVAL);
-
- opcode = stm_opcodes[SPI_PAGE_PROGRAM].code;
- bytes_left = len;
-
- do {
- u32 xact_len, reg, page_offset, spi_data = 0;
-
- xact_len = MIN(bytes_left, sizeof(__u32));
-
- /* 32-bit writes cannot span across a page boundary
- * (256 bytes). This types of writes require two page
- * program operations to handle it correctly. The STM part
- * will write the overflow data to the beginning of the
- * current page as opposed to the subsequent page.
- */
- page_offset = (to & (STM_PAGE_SIZE - 1)) + xact_len;
-
- if (page_offset > STM_PAGE_SIZE) {
- xact_len -= (page_offset - STM_PAGE_SIZE);
- }
-
- if (!spiflash_wait_ready(FL_WRITING))
- return -EINTR;
-
- spiflash_sendcmd(SPI_WRITE_ENABLE, 0);
- switch (xact_len) {
- case 1:
- spi_data = (u32) ((u8) *buf);
- break;
- case 2:
- spi_data = (buf[1] << 8) | buf[0];
- break;
- case 3:
- spi_data = (buf[2] << 16) | (buf[1] << 8) | buf[0];
- break;
- case 4:
- spi_data = (buf[3] << 24) | (buf[2] << 16) |
- (buf[1] << 8) | buf[0];
- break;
- default:
- spi_data = 0;
- break;
- }
-
- spiflash_regwrite32(SPI_FLASH_DATA, spi_data);
- opcode = (opcode & SPI_OPCODE_MASK) | ((__u32)to << 8);
- spiflash_regwrite32(SPI_FLASH_OPCODE, opcode);
-
- reg = spiflash_regread32(SPI_FLASH_CTL);
- reg = (reg & ~SPI_CTL_TX_RX_CNT_MASK) | (xact_len + 4) | SPI_CTL_START;
- spiflash_regwrite32(SPI_FLASH_CTL, reg);
-
- /* give the chip some time before we start busy waiting */
- spin_unlock_bh(&spidata->mutex);
- schedule();
- spin_lock_bh(&spidata->mutex);
-
- busy_wait(spiflash_sendcmd(SPI_RD_STATUS, 0) & SPI_STATUS_WIP, 0);
- spiflash_done();
-
- bytes_left -= xact_len;
- to += xact_len;
- buf += xact_len;
-
- *retlen += xact_len;
- } while (bytes_left != 0);
-
- return 0;
-}
-
-
-#ifdef CONFIG_MTD_PARTITIONS
-static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", "MyLoader", NULL };
-#endif
-
-
-static int spiflash_probe(struct platform_device *pdev)
-{
- int result = -1;
- int index, num_parts;
- struct mtd_info *mtd;
-
- spidata->mmraddr = ioremap_nocache(SPI_FLASH_MMR, SPI_FLASH_MMR_SIZE);
- spin_lock_init(&spidata->mutex);
- init_waitqueue_head(&spidata->wq);
- spidata->state = FL_READY;
-
- if (!spidata->mmraddr) {
- printk (KERN_WARNING SPIFLASH "Failed to map flash device\n");
- kfree(spidata);
- spidata = NULL;
- }
-
- mtd = kzalloc(sizeof(struct mtd_info), GFP_KERNEL);
- if (!mtd) {
- kfree(spidata);
- return -ENXIO;
- }
-
- if (!(index = spiflash_probe_chip())) {
- printk (KERN_WARNING SPIFLASH "Found no serial flash device\n");
- goto error;
- }
-
- spidata->readaddr = ioremap_nocache(SPI_FLASH_READ, flashconfig_tbl[index].byte_cnt);
- if (!spidata->readaddr) {
- printk (KERN_WARNING SPIFLASH "Failed to map flash device\n");
- goto error;
- }
-
- mtd->name = "spiflash";
- mtd->type = MTD_NORFLASH;
- mtd->flags = (MTD_CAP_NORFLASH|MTD_WRITEABLE);
- mtd->size = flashconfig_tbl[index].byte_cnt;
- mtd->erasesize = flashconfig_tbl[index].sector_size;
- mtd->writesize = 1;
- mtd->numeraseregions = 0;
- mtd->eraseregions = NULL;
- mtd->erase = spiflash_erase;
- mtd->read = spiflash_read;
- mtd->write = spiflash_write;
- mtd->owner = THIS_MODULE;
-
- /* parse redboot partitions */
- num_parts = parse_mtd_partitions(mtd, part_probe_types, &spidata->parsed_parts, 0);
- if (!num_parts)
- goto error;
-
- result = add_mtd_partitions(mtd, spidata->parsed_parts, num_parts);
- spidata->mtd = mtd;
-
- return (result);
-
-error:
- kfree(mtd);
- kfree(spidata);
- return -ENXIO;
-}
-
-static int spiflash_remove (struct platform_device *pdev)
-{
- del_mtd_partitions (spidata->mtd);
- kfree(spidata->mtd);
- return 0;
-}
-
-struct platform_driver spiflash_driver = {
- .driver.name = "spiflash",
- .probe = spiflash_probe,
- .remove = spiflash_remove,
-};
-
-int __init
-spiflash_init (void)
-{
- spidata = kmalloc(sizeof(struct spiflash_data), GFP_KERNEL);
- if (!spidata)
- return (-ENXIO);
-
- spin_lock_init(&spidata->mutex);
- platform_driver_register(&spiflash_driver);
-
- return 0;
-}
-
-void __exit
-spiflash_exit (void)
-{
- kfree(spidata);
-}
-
-module_init (spiflash_init);
-module_exit (spiflash_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("OpenWrt.org, Atheros Communications Inc");
-MODULE_DESCRIPTION("MTD driver for SPI Flash on Atheros SOC");
-
+++ /dev/null
-/*
- * SPI Flash Memory support header file.
- *
- * $Id: //depot/sw/releases/linuxsrc/src/kernels/mips-linux-2.4.25/drivers/mtd/devices/spiflash.h#3 $
- *
- *
- * Copyright (c) 2005, Atheros Communications Inc.
- * Copyright (C) 2006 FON Technology, SL.
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- *
- * This code is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#define FLASH_1MB 1
-#define FLASH_2MB 2
-#define FLASH_4MB 3
-#define FLASH_8MB 4
-#define FLASH_16MB 5
-#define MAX_FLASH 6
-
-#define STM_PAGE_SIZE 256
-
-#define SFI_WRITE_BUFFER_SIZE 4
-#define SFI_FLASH_ADDR_MASK 0x00ffffff
-
-#define STM_8MBIT_SIGNATURE 0x13
-#define STM_M25P80_BYTE_COUNT 1048576
-#define STM_M25P80_SECTOR_COUNT 16
-#define STM_M25P80_SECTOR_SIZE 0x10000
-
-#define STM_16MBIT_SIGNATURE 0x14
-#define STM_M25P16_BYTE_COUNT 2097152
-#define STM_M25P16_SECTOR_COUNT 32
-#define STM_M25P16_SECTOR_SIZE 0x10000
-
-#define STM_32MBIT_SIGNATURE 0x15
-#define STM_M25P32_BYTE_COUNT 4194304
-#define STM_M25P32_SECTOR_COUNT 64
-#define STM_M25P32_SECTOR_SIZE 0x10000
-
-#define STM_64MBIT_SIGNATURE 0x16
-#define STM_M25P64_BYTE_COUNT 8388608
-#define STM_M25P64_SECTOR_COUNT 128
-#define STM_M25P64_SECTOR_SIZE 0x10000
-
-#define STM_128MBIT_SIGNATURE 0x17
-#define STM_M25P128_BYTE_COUNT 16777216
-#define STM_M25P128_SECTOR_COUNT 256
-#define STM_M25P128_SECTOR_SIZE 0x10000
-
-#define STM_1MB_BYTE_COUNT STM_M25P80_BYTE_COUNT
-#define STM_1MB_SECTOR_COUNT STM_M25P80_SECTOR_COUNT
-#define STM_1MB_SECTOR_SIZE STM_M25P80_SECTOR_SIZE
-#define STM_2MB_BYTE_COUNT STM_M25P16_BYTE_COUNT
-#define STM_2MB_SECTOR_COUNT STM_M25P16_SECTOR_COUNT
-#define STM_2MB_SECTOR_SIZE STM_M25P16_SECTOR_SIZE
-#define STM_4MB_BYTE_COUNT STM_M25P32_BYTE_COUNT
-#define STM_4MB_SECTOR_COUNT STM_M25P32_SECTOR_COUNT
-#define STM_4MB_SECTOR_SIZE STM_M25P32_SECTOR_SIZE
-#define STM_8MB_BYTE_COUNT STM_M25P64_BYTE_COUNT
-#define STM_8MB_SECTOR_COUNT STM_M25P64_SECTOR_COUNT
-#define STM_8MB_SECTOR_SIZE STM_M25P64_SECTOR_SIZE
-#define STM_16MB_BYTE_COUNT STM_M25P128_BYTE_COUNT
-#define STM_16MB_SECTOR_COUNT STM_M25P128_SECTOR_COUNT
-#define STM_16MB_SECTOR_SIZE STM_M25P128_SECTOR_SIZE
-
-/*
- * ST Microelectronics Opcodes for Serial Flash
- */
-
-#define STM_OP_WR_ENABLE 0x06 /* Write Enable */
-#define STM_OP_WR_DISABLE 0x04 /* Write Disable */
-#define STM_OP_RD_STATUS 0x05 /* Read Status */
-#define STM_OP_WR_STATUS 0x01 /* Write Status */
-#define STM_OP_RD_DATA 0x03 /* Read Data */
-#define STM_OP_FAST_RD_DATA 0x0b /* Fast Read Data */
-#define STM_OP_PAGE_PGRM 0x02 /* Page Program */
-#define STM_OP_SECTOR_ERASE 0xd8 /* Sector Erase */
-#define STM_OP_BULK_ERASE 0xc7 /* Bulk Erase */
-#define STM_OP_DEEP_PWRDOWN 0xb9 /* Deep Power-Down Mode */
-#define STM_OP_RD_SIG 0xab /* Read Electronic Signature */
-
-#define STM_STATUS_WIP 0x01 /* Write-In-Progress */
-#define STM_STATUS_WEL 0x02 /* Write Enable Latch */
-#define STM_STATUS_BP0 0x04 /* Block Protect 0 */
-#define STM_STATUS_BP1 0x08 /* Block Protect 1 */
-#define STM_STATUS_BP2 0x10 /* Block Protect 2 */
-#define STM_STATUS_SRWD 0x80 /* Status Register Write Disable */
-
-/*
- * SPI Flash Interface Registers
- */
-#define AR531XPLUS_SPI_READ 0x08000000
-#define AR531XPLUS_SPI_MMR 0x11300000
-#define AR531XPLUS_SPI_MMR_SIZE 12
-
-#define AR531XPLUS_SPI_CTL 0x00
-#define AR531XPLUS_SPI_OPCODE 0x04
-#define AR531XPLUS_SPI_DATA 0x08
-
-#define SPI_FLASH_READ AR531XPLUS_SPI_READ
-#define SPI_FLASH_MMR AR531XPLUS_SPI_MMR
-#define SPI_FLASH_MMR_SIZE AR531XPLUS_SPI_MMR_SIZE
-#define SPI_FLASH_CTL AR531XPLUS_SPI_CTL
-#define SPI_FLASH_OPCODE AR531XPLUS_SPI_OPCODE
-#define SPI_FLASH_DATA AR531XPLUS_SPI_DATA
-
-#define SPI_CTL_START 0x00000100
-#define SPI_CTL_BUSY 0x00010000
-#define SPI_CTL_TXCNT_MASK 0x0000000f
-#define SPI_CTL_RXCNT_MASK 0x000000f0
-#define SPI_CTL_TX_RX_CNT_MASK 0x000000ff
-#define SPI_CTL_SIZE_MASK 0x00060000
-
-#define SPI_CTL_CLK_SEL_MASK 0x03000000
-#define SPI_OPCODE_MASK 0x000000ff
-
-#define SPI_STATUS_WIP STM_STATUS_WIP
+++ /dev/null
-#
-# Makefile for the AR2313 ethernet driver
-#
-
-obj-$(CONFIG_AR2313) += ar2313.o
+++ /dev/null
-/*
- * ar2313.c: Linux driver for the Atheros AR231x Ethernet device.
- *
- * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
- * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
- * Copyright (C) 2006-2007 Felix Fietkau <nbd@openwrt.org>
- *
- * Thanks to Atheros for providing hardware and documentation
- * enabling me to write this driver.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * Additional credits:
- * This code is taken from John Taylor's Sibyte driver and then
- * modified for the AR2313.
- */
-
-#include <linux/autoconf.h>
-#include <linux/module.h>
-#include <linux/version.h>
-#include <linux/types.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/pci.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/mm.h>
-#include <linux/highmem.h>
-#include <linux/sockios.h>
-#include <linux/pkt_sched.h>
-#include <linux/compile.h>
-#include <linux/mii.h>
-#include <linux/phy.h>
-#include <linux/ethtool.h>
-#include <linux/ctype.h>
-#include <linux/platform_device.h>
-
-#include <net/sock.h>
-#include <net/ip.h>
-
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/byteorder.h>
-#include <asm/uaccess.h>
-#include <asm/bootinfo.h>
-
-#define AR2313_MTU 1692
-#define AR2313_PRIOS 1
-#define AR2313_QUEUES (2*AR2313_PRIOS)
-#define AR2313_DESCR_ENTRIES 64
-
-#undef INDEX_DEBUG
-#define DEBUG 0
-#define DEBUG_TX 0
-#define DEBUG_RX 0
-#define DEBUG_INT 0
-#define DEBUG_MC 0
-#define DEBUG_ERR 1
-
-#ifndef min
-#define min(a,b) (((a)<(b))?(a):(b))
-#endif
-
-#ifndef SMP_CACHE_BYTES
-#define SMP_CACHE_BYTES L1_CACHE_BYTES
-#endif
-
-#define AR2313_MBOX_SET_BIT 0x8
-
-#define BOARD_IDX_STATIC 0
-#define BOARD_IDX_OVERFLOW -1
-
-#include "dma.h"
-#include "ar2313.h"
-
-/*
- * New interrupt handler strategy:
- *
- * An old interrupt handler worked using the traditional method of
- * replacing an skbuff with a new one when a packet arrives. However
- * the rx rings do not need to contain a static number of buffer
- * descriptors, thus it makes sense to move the memory allocation out
- * of the main interrupt handler and do it in a bottom half handler
- * and only allocate new buffers when the number of buffers in the
- * ring is below a certain threshold. In order to avoid starving the
- * NIC under heavy load it is however necessary to force allocation
- * when hitting a minimum threshold. The strategy for alloction is as
- * follows:
- *
- * RX_LOW_BUF_THRES - allocate buffers in the bottom half
- * RX_PANIC_LOW_THRES - we are very low on buffers, allocate
- * the buffers in the interrupt handler
- * RX_RING_THRES - maximum number of buffers in the rx ring
- *
- * One advantagous side effect of this allocation approach is that the
- * entire rx processing can be done without holding any spin lock
- * since the rx rings and registers are totally independent of the tx
- * ring and its registers. This of course includes the kmalloc's of
- * new skb's. Thus start_xmit can run in parallel with rx processing
- * and the memory allocation on SMP systems.
- *
- * Note that running the skb reallocation in a bottom half opens up
- * another can of races which needs to be handled properly. In
- * particular it can happen that the interrupt handler tries to run
- * the reallocation while the bottom half is either running on another
- * CPU or was interrupted on the same CPU. To get around this the
- * driver uses bitops to prevent the reallocation routines from being
- * reentered.
- *
- * TX handling can also be done without holding any spin lock, wheee
- * this is fun! since tx_csm is only written to by the interrupt
- * handler.
- */
-
-/*
- * Threshold values for RX buffer allocation - the low water marks for
- * when to start refilling the rings are set to 75% of the ring
- * sizes. It seems to make sense to refill the rings entirely from the
- * intrrupt handler once it gets below the panic threshold, that way
- * we don't risk that the refilling is moved to another CPU when the
- * one running the interrupt handler just got the slab code hot in its
- * cache.
- */
-#define RX_RING_SIZE AR2313_DESCR_ENTRIES
-#define RX_PANIC_THRES (RX_RING_SIZE/4)
-#define RX_LOW_THRES ((3*RX_RING_SIZE)/4)
-#define CRC_LEN 4
-#define RX_OFFSET 2
-
-#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
-#define VLAN_HDR 4
-#else
-#define VLAN_HDR 0
-#endif
-
-#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + RX_OFFSET)
-
-#ifdef MODULE
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@openwrt.org>");
-MODULE_DESCRIPTION("AR2313 Ethernet driver");
-#endif
-
-#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
-
-// prototypes
-#ifdef TX_TIMEOUT
-static void ar2313_tx_timeout(struct net_device *dev);
-#endif
-static void ar2313_halt(struct net_device *dev);
-static void rx_tasklet_func(unsigned long data);
-static void rx_tasklet_cleanup(struct net_device *dev);
-static void ar2313_multicast_list(struct net_device *dev);
-
-static int mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
-static int mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value);
-static int mdiobus_reset(struct mii_bus *bus);
-static int mdiobus_probe (struct net_device *dev);
-static void ar2313_adjust_link(struct net_device *dev);
-
-#ifndef ERR
-#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
-#endif
-
-
-int __init ar2313_probe(struct platform_device *pdev)
-{
- struct net_device *dev;
- struct ar2313_private *sp;
- struct resource *res;
- unsigned long ar_eth_base;
- char buf[64];
-
- dev = alloc_etherdev(sizeof(struct ar2313_private));
-
- if (dev == NULL) {
- printk(KERN_ERR
- "ar2313: Unable to allocate net_device structure!\n");
- return -ENOMEM;
- }
-
- platform_set_drvdata(pdev, dev);
-
- sp = netdev_priv(dev);
- sp->dev = dev;
- sp->cfg = pdev->dev.platform_data;
-
- sprintf(buf, "eth%d_membase", pdev->id);
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
- if (!res)
- return -ENODEV;
-
- sp->link = 0;
- ar_eth_base = res->start;
- sp->phy = sp->cfg->phy;
-
- sprintf(buf, "eth%d_irq", pdev->id);
- dev->irq = platform_get_irq_byname(pdev, buf);
-
- spin_lock_init(&sp->lock);
-
- /* initialize func pointers */
- dev->open = &ar2313_open;
- dev->stop = &ar2313_close;
- dev->hard_start_xmit = &ar2313_start_xmit;
-
- dev->set_multicast_list = &ar2313_multicast_list;
-#ifdef TX_TIMEOUT
- dev->tx_timeout = ar2313_tx_timeout;
- dev->watchdog_timeo = AR2313_TX_TIMEOUT;
-#endif
- dev->do_ioctl = &ar2313_ioctl;
-
- // SAMEER: do we need this?
- dev->features |= NETIF_F_HIGHDMA;
-
- tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long) dev);
- tasklet_disable(&sp->rx_tasklet);
-
- sp->eth_regs =
- ioremap_nocache(virt_to_phys(ar_eth_base), sizeof(*sp->eth_regs));
- if (!sp->eth_regs) {
- printk("Can't remap eth registers\n");
- return (-ENXIO);
- }
-
- /*
- * When there's only one MAC, PHY regs are typically on ENET0,
- * even though the MAC might be on ENET1.
- * Needto remap PHY regs separately in this case
- */
- if (virt_to_phys(ar_eth_base) == virt_to_phys(sp->phy_regs))
- sp->phy_regs = sp->eth_regs;
- else {
- sp->phy_regs =
- ioremap_nocache(virt_to_phys(sp->cfg->phy_base),
- sizeof(*sp->phy_regs));
- if (!sp->phy_regs) {
- printk("Can't remap phy registers\n");
- return (-ENXIO);
- }
- }
-
- sp->dma_regs =
- ioremap_nocache(virt_to_phys(ar_eth_base + 0x1000),
- sizeof(*sp->dma_regs));
- dev->base_addr = (unsigned int) sp->dma_regs;
- if (!sp->dma_regs) {
- printk("Can't remap DMA registers\n");
- return (-ENXIO);
- }
-
- sp->int_regs = ioremap_nocache(virt_to_phys(sp->cfg->reset_base), 4);
- if (!sp->int_regs) {
- printk("Can't remap INTERRUPT registers\n");
- return (-ENXIO);
- }
-
- strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
- sp->name[sizeof(sp->name) - 1] = '\0';
- memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
- sp->board_idx = BOARD_IDX_STATIC;
-
- if (ar2313_init(dev)) {
- /*
- * ar2313_init() calls ar2313_init_cleanup() on error.
- */
- kfree(dev);
- return -ENODEV;
- }
-
- if (register_netdev(dev)) {
- printk("%s: register_netdev failed\n", __func__);
- return -1;
- }
-
- printk("%s: %s: %02x:%02x:%02x:%02x:%02x:%02x, irq %d\n",
- dev->name, sp->name,
- dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
- dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5], dev->irq);
-
- sp->mii_bus.priv = dev;
- sp->mii_bus.read = mdiobus_read;
- sp->mii_bus.write = mdiobus_write;
- sp->mii_bus.reset = mdiobus_reset;
- sp->mii_bus.name = "ar2313_eth_mii";
- sp->mii_bus.id = 0;
- sp->mii_bus.irq = kmalloc(sizeof(int), GFP_KERNEL);
- *sp->mii_bus.irq = PHY_POLL;
-
- mdiobus_register(&sp->mii_bus);
-
- if (mdiobus_probe(dev) != 0) {
- printk(KERN_ERR "ar2313: mdiobus_probe failed");
- rx_tasklet_cleanup(dev);
- ar2313_init_cleanup(dev);
- unregister_netdev(dev);
- kfree(dev);
- } else {
- /* start link poll timer */
- ar2313_setup_timer(dev);
- }
-
- return 0;
-}
-
-#if 0
-static void ar2313_dump_regs(struct net_device *dev)
-{
- unsigned int *ptr, i;
- struct ar2313_private *sp = netdev_priv(dev);
-
- ptr = (unsigned int *) sp->eth_regs;
- for (i = 0; i < (sizeof(ETHERNET_STRUCT) / sizeof(unsigned int));
- i++, ptr++) {
- printk("ENET: %08x = %08x\n", (int) ptr, *ptr);
- }
-
- ptr = (unsigned int *) sp->dma_regs;
- for (i = 0; i < (sizeof(DMA) / sizeof(unsigned int)); i++, ptr++) {
- printk("DMA: %08x = %08x\n", (int) ptr, *ptr);
- }
-
- ptr = (unsigned int *) sp->int_regs;
- for (i = 0; i < (sizeof(INTERRUPT) / sizeof(unsigned int)); i++, ptr++) {
- printk("INT: %08x = %08x\n", (int) ptr, *ptr);
- }
-
- for (i = 0; i < AR2313_DESCR_ENTRIES; i++) {
- ar2313_descr_t *td = &sp->tx_ring[i];
- printk("Tx desc %2d: %08x %08x %08x %08x\n", i,
- td->status, td->devcs, td->addr, td->descr);
- }
-}
-#endif
-
-#ifdef TX_TIMEOUT
-static void ar2313_tx_timeout(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- unsigned long flags;
-
-#if DEBUG_TX
- printk("Tx timeout\n");
-#endif
- spin_lock_irqsave(&sp->lock, flags);
- ar2313_restart(dev);
- spin_unlock_irqrestore(&sp->lock, flags);
-}
-#endif
-
-#if DEBUG_MC
-static void printMcList(struct net_device *dev)
-{
- struct dev_mc_list *list = dev->mc_list;
- int num = 0, i;
- while (list) {
- printk("%d MC ADDR ", num);
- for (i = 0; i < list->dmi_addrlen; i++) {
- printk(":%02x", list->dmi_addr[i]);
- }
- list = list->next;
- printk("\n");
- }
-}
-#endif
-
-/*
- * Set or clear the multicast filter for this adaptor.
- * THIS IS ABSOLUTE CRAP, disabled
- */
-static void ar2313_multicast_list(struct net_device *dev)
-{
- /*
- * Always listen to broadcasts and
- * treat IFF bits independently
- */
- struct ar2313_private *sp = netdev_priv(dev);
- unsigned int recognise;
-
- recognise = sp->eth_regs->mac_control;
-
- if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
- recognise |= MAC_CONTROL_PR;
- } else {
- recognise &= ~MAC_CONTROL_PR;
- }
-
- if ((dev->flags & IFF_ALLMULTI) || (dev->mc_count > 15)) {
-#if DEBUG_MC
- printMcList(dev);
- printk("%s: all MULTICAST mc_count %d\n", __FUNCTION__,
- dev->mc_count);
-#endif
- recognise |= MAC_CONTROL_PM; /* all multicast */
- } else if (dev->mc_count > 0) {
-#if DEBUG_MC
- printMcList(dev);
- printk("%s: mc_count %d\n", __FUNCTION__, dev->mc_count);
-#endif
- recognise |= MAC_CONTROL_PM; /* for the time being */
- }
-#if DEBUG_MC
- printk("%s: setting %08x to %08x\n", __FUNCTION__, (int) sp->eth_regs,
- recognise);
-#endif
-
- sp->eth_regs->mac_control = recognise;
-}
-
-static void rx_tasklet_cleanup(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
-
- /*
- * Tasklet may be scheduled. Need to get it removed from the list
- * since we're about to free the struct.
- */
-
- sp->unloading = 1;
- tasklet_enable(&sp->rx_tasklet);
- tasklet_kill(&sp->rx_tasklet);
-}
-
-static int __exit ar2313_remove(struct platform_device *pdev)
-{
- struct net_device *dev = platform_get_drvdata(pdev);
- rx_tasklet_cleanup(dev);
- ar2313_init_cleanup(dev);
- unregister_netdev(dev);
- kfree(dev);
- return 0;
-}
-
-
-/*
- * Restart the AR2313 ethernet controller.
- */
-static int ar2313_restart(struct net_device *dev)
-{
- /* disable interrupts */
- disable_irq(dev->irq);
-
- /* stop mac */
- ar2313_halt(dev);
-
- /* initialize */
- ar2313_init(dev);
-
- /* enable interrupts */
- enable_irq(dev->irq);
-
- return 0;
-}
-
-static struct platform_driver ar2313_driver = {
- .driver.name = "ar531x-eth",
- .probe = ar2313_probe,
- .remove = ar2313_remove,
-};
-
-int __init ar2313_module_init(void)
-{
- return platform_driver_register(&ar2313_driver);
-}
-
-void __exit ar2313_module_cleanup(void)
-{
- platform_driver_unregister(&ar2313_driver);
-}
-
-module_init(ar2313_module_init);
-module_exit(ar2313_module_cleanup);
-
-
-static void ar2313_free_descriptors(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- if (sp->rx_ring != NULL) {
- kfree((void *) KSEG0ADDR(sp->rx_ring));
- sp->rx_ring = NULL;
- sp->tx_ring = NULL;
- }
-}
-
-
-static int ar2313_allocate_descriptors(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- int size;
- int j;
- ar2313_descr_t *space;
-
- if (sp->rx_ring != NULL) {
- printk("%s: already done.\n", __FUNCTION__);
- return 0;
- }
-
- size =
- (sizeof(ar2313_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES));
- space = kmalloc(size, GFP_KERNEL);
- if (space == NULL)
- return 1;
-
- /* invalidate caches */
- dma_cache_inv((unsigned int) space, size);
-
- /* now convert pointer to KSEG1 */
- space = (ar2313_descr_t *) KSEG1ADDR(space);
-
- memset((void *) space, 0, size);
-
- sp->rx_ring = space;
- space += AR2313_DESCR_ENTRIES;
-
- sp->tx_ring = space;
- space += AR2313_DESCR_ENTRIES;
-
- /* Initialize the transmit Descriptors */
- for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
- ar2313_descr_t *td = &sp->tx_ring[j];
- td->status = 0;
- td->devcs = DMA_TX1_CHAINED;
- td->addr = 0;
- td->descr =
- virt_to_phys(&sp->
- tx_ring[(j + 1) & (AR2313_DESCR_ENTRIES - 1)]);
- }
-
- return 0;
-}
-
-
-/*
- * Generic cleanup handling data allocated during init. Used when the
- * module is unloaded or if an error occurs during initialization
- */
-static void ar2313_init_cleanup(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- struct sk_buff *skb;
- int j;
-
- ar2313_free_descriptors(dev);
-
- if (sp->eth_regs)
- iounmap((void *) sp->eth_regs);
- if (sp->dma_regs)
- iounmap((void *) sp->dma_regs);
-
- if (sp->rx_skb) {
- for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
- skb = sp->rx_skb[j];
- if (skb) {
- sp->rx_skb[j] = NULL;
- dev_kfree_skb(skb);
- }
- }
- kfree(sp->rx_skb);
- sp->rx_skb = NULL;
- }
-
- if (sp->tx_skb) {
- for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
- skb = sp->tx_skb[j];
- if (skb) {
- sp->tx_skb[j] = NULL;
- dev_kfree_skb(skb);
- }
- }
- kfree(sp->tx_skb);
- sp->tx_skb = NULL;
- }
-}
-
-static int ar2313_setup_timer(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
-
- init_timer(&sp->link_timer);
-
- sp->link_timer.function = ar2313_link_timer_fn;
- sp->link_timer.data = (int) dev;
- sp->link_timer.expires = jiffies + HZ;
-
- add_timer(&sp->link_timer);
- return 0;
-
-}
-
-static void ar2313_link_timer_fn(unsigned long data)
-{
- struct net_device *dev = (struct net_device *) data;
- struct ar2313_private *sp = netdev_priv(dev);
-
- // see if the link status changed
- // This was needed to make sure we set the PHY to the
- // autonegotiated value of half or full duplex.
- ar2313_check_link(dev);
-
- // Loop faster when we don't have link.
- // This was needed to speed up the AP bootstrap time.
- if (sp->link == 0) {
- mod_timer(&sp->link_timer, jiffies + HZ / 2);
- } else {
- mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
- }
-}
-
-static void ar2313_check_link(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- u16 phyData;
-
- phyData = mdiobus_read(&sp->mii_bus, sp->phy, MII_BMSR);
- if (sp->phyData != phyData) {
- if (phyData & BMSR_LSTATUS) {
- /* link is present, ready link partner ability to deterine
- duplexity */
- int duplex = 0;
- u16 reg;
-
- sp->link = 1;
- reg = mdiobus_read(&sp->mii_bus, sp->phy, MII_BMCR);
- if (reg & BMCR_ANENABLE) {
- /* auto neg enabled */
- reg = mdiobus_read(&sp->mii_bus, sp->phy, MII_LPA);
- duplex = (reg & (LPA_100FULL | LPA_10FULL)) ? 1 : 0;
- } else {
- /* no auto neg, just read duplex config */
- duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
- }
-
- printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
- dev->name, (duplex) ? "full" : "half");
-
- if (duplex) {
- /* full duplex */
- sp->eth_regs->mac_control =
- ((sp->eth_regs->
- mac_control | MAC_CONTROL_F) & ~MAC_CONTROL_DRO);
- } else {
- /* half duplex */
- sp->eth_regs->mac_control =
- ((sp->eth_regs->
- mac_control | MAC_CONTROL_DRO) & ~MAC_CONTROL_F);
- }
- } else {
- /* no link */
- sp->link = 0;
- }
- sp->phyData = phyData;
- }
-}
-
-static int ar2313_reset_reg(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- unsigned int ethsal, ethsah;
- unsigned int flags;
-
- *sp->int_regs |= sp->cfg->reset_mac;
- mdelay(10);
- *sp->int_regs &= ~sp->cfg->reset_mac;
- mdelay(10);
- *sp->int_regs |= sp->cfg->reset_phy;
- mdelay(10);
- *sp->int_regs &= ~sp->cfg->reset_phy;
- mdelay(10);
-
- sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
- mdelay(10);
- sp->dma_regs->bus_mode =
- ((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
-
- /* enable interrupts */
- sp->dma_regs->intr_ena = (DMA_STATUS_AIS |
- DMA_STATUS_NIS |
- DMA_STATUS_RI |
- DMA_STATUS_TI | DMA_STATUS_FBE);
- sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
- sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
- sp->dma_regs->control =
- (DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
-
- sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
- sp->eth_regs->vlan_tag = (0x8100);
-
- /* Enable Ethernet Interface */
- flags = (MAC_CONTROL_TE | /* transmit enable */
- MAC_CONTROL_PM | /* pass mcast */
- MAC_CONTROL_F | /* full duplex */
- MAC_CONTROL_HBD); /* heart beat disabled */
-
- if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
- flags |= MAC_CONTROL_PR;
- }
- sp->eth_regs->mac_control = flags;
-
- /* Set all Ethernet station address registers to their initial values */
- ethsah = ((((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
- (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF));
-
- ethsal = ((((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
- (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
- (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
- (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF));
-
- sp->eth_regs->mac_addr[0] = ethsah;
- sp->eth_regs->mac_addr[1] = ethsal;
-
- mdelay(10);
-
- return (0);
-}
-
-
-static int ar2313_init(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- int ecode = 0;
-
- /*
- * Allocate descriptors
- */
- if (ar2313_allocate_descriptors(dev)) {
- printk("%s: %s: ar2313_allocate_descriptors failed\n",
- dev->name, __FUNCTION__);
- ecode = -EAGAIN;
- goto init_error;
- }
-
- /*
- * Get the memory for the skb rings.
- */
- if (sp->rx_skb == NULL) {
- sp->rx_skb =
- kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
- GFP_KERNEL);
- if (!(sp->rx_skb)) {
- printk("%s: %s: rx_skb kmalloc failed\n",
- dev->name, __FUNCTION__);
- ecode = -EAGAIN;
- goto init_error;
- }
- }
- memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
-
- if (sp->tx_skb == NULL) {
- sp->tx_skb =
- kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
- GFP_KERNEL);
- if (!(sp->tx_skb)) {
- printk("%s: %s: tx_skb kmalloc failed\n",
- dev->name, __FUNCTION__);
- ecode = -EAGAIN;
- goto init_error;
- }
- }
- memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
-
- /*
- * Set tx_csm before we start receiving interrupts, otherwise
- * the interrupt handler might think it is supposed to process
- * tx ints before we are up and running, which may cause a null
- * pointer access in the int handler.
- */
- sp->rx_skbprd = 0;
- sp->cur_rx = 0;
- sp->tx_prd = 0;
- sp->tx_csm = 0;
-
- /*
- * Zero the stats before starting the interface
- */
- memset(&dev->stats, 0, sizeof(dev->stats));
-
- /*
- * We load the ring here as there seem to be no way to tell the
- * firmware to wipe the ring without re-initializing it.
- */
- ar2313_load_rx_ring(dev, RX_RING_SIZE);
-
- /*
- * Init hardware
- */
- ar2313_reset_reg(dev);
-
- /*
- * Get the IRQ
- */
- ecode =
- request_irq(dev->irq, &ar2313_interrupt,
- IRQF_SHARED | IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
- dev->name, dev);
- if (ecode) {
- printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
- dev->name, __FUNCTION__, dev->irq);
- goto init_error;
- }
-
-
- tasklet_enable(&sp->rx_tasklet);
-
- return 0;
-
- init_error:
- ar2313_init_cleanup(dev);
- return ecode;
-}
-
-/*
- * Load the rx ring.
- *
- * Loading rings is safe without holding the spin lock since this is
- * done only before the device is enabled, thus no interrupts are
- * generated and by the interrupt handler/tasklet handler.
- */
-static void ar2313_load_rx_ring(struct net_device *dev, int nr_bufs)
-{
-
- struct ar2313_private *sp = netdev_priv(dev);
- short i, idx;
-
- idx = sp->rx_skbprd;
-
- for (i = 0; i < nr_bufs; i++) {
- struct sk_buff *skb;
- ar2313_descr_t *rd;
-
- if (sp->rx_skb[idx]) {
-#if DEBUG_RX
- printk(KERN_INFO "ar2313 rx refill full\n");
-#endif /* DEBUG */
- break;
- }
- // partha: create additional room for the second GRE fragment
- skb = alloc_skb(AR2313_BUFSIZE + 128, GFP_ATOMIC);
- if (!skb) {
- printk("\n\n\n\n %s: No memory in system\n\n\n\n",
- __FUNCTION__);
- break;
- }
- // partha: create additional room in the front for tx pkt capture
- skb_reserve(skb, 32);
-
- /*
- * Make sure IP header starts on a fresh cache line.
- */
- skb->dev = dev;
- skb_reserve(skb, RX_OFFSET);
- sp->rx_skb[idx] = skb;
-
- rd = (ar2313_descr_t *) & sp->rx_ring[idx];
-
- /* initialize dma descriptor */
- rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
- DMA_RX1_CHAINED);
- rd->addr = virt_to_phys(skb->data);
- rd->descr =
- virt_to_phys(&sp->
- rx_ring[(idx + 1) & (AR2313_DESCR_ENTRIES - 1)]);
- rd->status = DMA_RX_OWN;
-
- idx = DSC_NEXT(idx);
- }
-
- if (!i) {
-#if DEBUG_ERR
- printk(KERN_INFO
- "Out of memory when allocating standard receive buffers\n");
-#endif /* DEBUG */
- } else {
- sp->rx_skbprd = idx;
- }
-
- return;
-}
-
-#define AR2313_MAX_PKTS_PER_CALL 64
-
-static int ar2313_rx_int(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- struct sk_buff *skb, *skb_new;
- ar2313_descr_t *rxdesc;
- unsigned int status;
- u32 idx;
- int pkts = 0;
- int rval;
-
- idx = sp->cur_rx;
-
- /* process at most the entire ring and then wait for another interrupt
- */
- while (1) {
-
- rxdesc = &sp->rx_ring[idx];
- status = rxdesc->status;
- if (status & DMA_RX_OWN) {
- /* SiByte owns descriptor or descr not yet filled in */
- rval = 0;
- break;
- }
-
- if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
- rval = 1;
- break;
- }
-#if DEBUG_RX
- printk("index %d\n", idx);
- printk("RX status %08x\n", rxdesc->status);
- printk("RX devcs %08x\n", rxdesc->devcs);
- printk("RX addr %08x\n", rxdesc->addr);
- printk("RX descr %08x\n", rxdesc->descr);
-#endif
-
- if ((status & (DMA_RX_ERROR | DMA_RX_ERR_LENGTH)) &&
- (!(status & DMA_RX_LONG))) {
-#if DEBUG_RX
- printk("%s: rx ERROR %08x\n", __FUNCTION__, status);
-#endif
- dev->stats.rx_errors++;
- dev->stats.rx_dropped++;
-
- /* add statistics counters */
- if (status & DMA_RX_ERR_CRC)
- dev->stats.rx_crc_errors++;
- if (status & DMA_RX_ERR_COL)
- dev->stats.rx_over_errors++;
- if (status & DMA_RX_ERR_LENGTH)
- dev->stats.rx_length_errors++;
- if (status & DMA_RX_ERR_RUNT)
- dev->stats.rx_over_errors++;
- if (status & DMA_RX_ERR_DESC)
- dev->stats.rx_over_errors++;
-
- } else {
- /* alloc new buffer. */
- skb_new = dev_alloc_skb(AR2313_BUFSIZE + RX_OFFSET + 128);
- if (skb_new != NULL) {
-
- skb = sp->rx_skb[idx];
- /* set skb */
- skb_put(skb,
- ((status >> DMA_RX_LEN_SHIFT) & 0x3fff) - CRC_LEN);
-
- dev->stats.rx_bytes += skb->len;
- skb->protocol = eth_type_trans(skb, dev);
- /* pass the packet to upper layers */
- netif_rx(skb);
-
- skb_new->dev = dev;
- /* 16 bit align */
- skb_reserve(skb_new, RX_OFFSET + 32);
- /* reset descriptor's curr_addr */
- rxdesc->addr = virt_to_phys(skb_new->data);
-
- dev->stats.rx_packets++;
- sp->rx_skb[idx] = skb_new;
- } else {
- dev->stats.rx_dropped++;
- }
- }
-
- rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
- DMA_RX1_CHAINED);
- rxdesc->status = DMA_RX_OWN;
-
- idx = DSC_NEXT(idx);
- }
-
- sp->cur_rx = idx;
-
- return rval;
-}
-
-
-static void ar2313_tx_int(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- u32 idx;
- struct sk_buff *skb;
- ar2313_descr_t *txdesc;
- unsigned int status = 0;
-
- idx = sp->tx_csm;
-
- while (idx != sp->tx_prd) {
-
- txdesc = &sp->tx_ring[idx];
-
-#if DEBUG_TX
- printk
- ("%s: TXINT: csm=%d idx=%d prd=%d status=%x devcs=%x addr=%08x descr=%x\n",
- dev->name, sp->tx_csm, idx, sp->tx_prd, txdesc->status,
- txdesc->devcs, txdesc->addr, txdesc->descr);
-#endif /* DEBUG */
-
- if ((status = txdesc->status) & DMA_TX_OWN) {
- /* ar2313 dma still owns descr */
- break;
- }
- /* done with this descriptor */
- dma_unmap_single(NULL, txdesc->addr,
- txdesc->devcs & DMA_TX1_BSIZE_MASK,
- DMA_TO_DEVICE);
- txdesc->status = 0;
-
- if (status & DMA_TX_ERROR) {
- dev->stats.tx_errors++;
- dev->stats.tx_dropped++;
- if (status & DMA_TX_ERR_UNDER)
- dev->stats.tx_fifo_errors++;
- if (status & DMA_TX_ERR_HB)
- dev->stats.tx_heartbeat_errors++;
- if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
- dev->stats.tx_carrier_errors++;
- if (status & (DMA_TX_ERR_LATE |
- DMA_TX_ERR_COL |
- DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
- dev->stats.tx_aborted_errors++;
- } else {
- /* transmit OK */
- dev->stats.tx_packets++;
- }
-
- skb = sp->tx_skb[idx];
- sp->tx_skb[idx] = NULL;
- idx = DSC_NEXT(idx);
- dev->stats.tx_bytes += skb->len;
- dev_kfree_skb_irq(skb);
- }
-
- sp->tx_csm = idx;
-
- return;
-}
-
-
-static void rx_tasklet_func(unsigned long data)
-{
- struct net_device *dev = (struct net_device *) data;
- struct ar2313_private *sp = netdev_priv(dev);
-
- if (sp->unloading) {
- return;
- }
-
- if (ar2313_rx_int(dev)) {
- tasklet_hi_schedule(&sp->rx_tasklet);
- } else {
- unsigned long flags;
- spin_lock_irqsave(&sp->lock, flags);
- sp->dma_regs->intr_ena |= DMA_STATUS_RI;
- spin_unlock_irqrestore(&sp->lock, flags);
- }
-}
-
-static void rx_schedule(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
-
- sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
-
- tasklet_hi_schedule(&sp->rx_tasklet);
-}
-
-static irqreturn_t ar2313_interrupt(int irq, void *dev_id)
-{
- struct net_device *dev = (struct net_device *) dev_id;
- struct ar2313_private *sp = netdev_priv(dev);
- unsigned int status, enabled;
-
- /* clear interrupt */
- /*
- * Don't clear RI bit if currently disabled.
- */
- status = sp->dma_regs->status;
- enabled = sp->dma_regs->intr_ena;
- sp->dma_regs->status = status & enabled;
-
- if (status & DMA_STATUS_NIS) {
- /* normal status */
- /*
- * Don't schedule rx processing if interrupt
- * is already disabled.
- */
- if (status & enabled & DMA_STATUS_RI) {
- /* receive interrupt */
- rx_schedule(dev);
- }
- if (status & DMA_STATUS_TI) {
- /* transmit interrupt */
- ar2313_tx_int(dev);
- }
- }
-
- if (status & DMA_STATUS_AIS) {
-#if DEBUG_INT
- printk("%s: AIS set %08x & %x\n", __FUNCTION__,
- status, (DMA_STATUS_FBE | DMA_STATUS_TPS));
-#endif
- /* abnormal status */
- if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS)) {
- ar2313_restart(dev);
- }
- }
- return IRQ_HANDLED;
-}
-
-
-static int ar2313_open(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- unsigned int ethsal, ethsah;
-
- /* reset the hardware, in case the MAC address changed */
- ethsah = ((((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
- (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF));
-
- ethsal = ((((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
- (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
- (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
- (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF));
-
- sp->eth_regs->mac_addr[0] = ethsah;
- sp->eth_regs->mac_addr[1] = ethsal;
-
- mdelay(10);
-
- dev->mtu = 1500;
- netif_start_queue(dev);
-
- sp->eth_regs->mac_control |= MAC_CONTROL_RE;
-
- return 0;
-}
-
-static void ar2313_halt(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- int j;
-
- tasklet_disable(&sp->rx_tasklet);
-
- /* kill the MAC */
- sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE | /* disable Receives */
- MAC_CONTROL_TE); /* disable Transmits */
- /* stop dma */
- sp->dma_regs->control = 0;
- sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
-
- /* place phy and MAC in reset */
- *sp->int_regs |= (sp->cfg->reset_mac | sp->cfg->reset_phy);
-
- /* free buffers on tx ring */
- for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
- struct sk_buff *skb;
- ar2313_descr_t *txdesc;
-
- txdesc = &sp->tx_ring[j];
- txdesc->descr = 0;
-
- skb = sp->tx_skb[j];
- if (skb) {
- dev_kfree_skb(skb);
- sp->tx_skb[j] = NULL;
- }
- }
-}
-
-/*
- * close should do nothing. Here's why. It's called when
- * 'ifconfig bond0 down' is run. If it calls free_irq then
- * the irq is gone forever ! When bond0 is made 'up' again,
- * the ar2313_open () does not call request_irq (). Worse,
- * the call to ar2313_halt() generates a WDOG reset due to
- * the write to 'sp->int_regs' and the box reboots.
- * Commenting this out is good since it allows the
- * system to resume when bond0 is made up again.
- */
-static int ar2313_close(struct net_device *dev)
-{
-#if 0
- /*
- * Disable interrupts
- */
- disable_irq(dev->irq);
-
- /*
- * Without (or before) releasing irq and stopping hardware, this
- * is an absolute non-sense, by the way. It will be reset instantly
- * by the first irq.
- */
- netif_stop_queue(dev);
-
- /* stop the MAC and DMA engines */
- ar2313_halt(dev);
-
- /* release the interrupt */
- free_irq(dev->irq, dev);
-
-#endif
- return 0;
-}
-
-static int ar2313_start_xmit(struct sk_buff *skb, struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- ar2313_descr_t *td;
- u32 idx;
-
- idx = sp->tx_prd;
- td = &sp->tx_ring[idx];
-
- if (td->status & DMA_TX_OWN) {
-#if DEBUG_TX
- printk("%s: No space left to Tx\n", __FUNCTION__);
-#endif
- /* free skbuf and lie to the caller that we sent it out */
- dev->stats.tx_dropped++;
- dev_kfree_skb(skb);
-
- /* restart transmitter in case locked */
- sp->dma_regs->xmt_poll = 0;
- return 0;
- }
-
- /* Setup the transmit descriptor. */
- td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
- (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
- td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
- td->status = DMA_TX_OWN;
-
- /* kick transmitter last */
- sp->dma_regs->xmt_poll = 0;
-
-#if DEBUG_TX
- printk("index %d\n", idx);
- printk("TX status %08x\n", td->status);
- printk("TX devcs %08x\n", td->devcs);
- printk("TX addr %08x\n", td->addr);
- printk("TX descr %08x\n", td->descr);
-#endif
-
- sp->tx_skb[idx] = skb;
- idx = DSC_NEXT(idx);
- sp->tx_prd = idx;
-
- return 0;
-}
-
-static int ar2313_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-{
- struct mii_ioctl_data *data = (struct mii_ioctl_data *) &ifr->ifr_data;
- struct ar2313_private *sp = netdev_priv(dev);
- int ret;
-
- switch (cmd) {
-
- case SIOCETHTOOL:
- spin_lock_irq(&sp->lock);
- ret = phy_ethtool_ioctl(sp->phy_dev, (void *) ifr->ifr_data);
- spin_unlock_irq(&sp->lock);
- return ret;
-
- case SIOCSIFHWADDR:
- if (copy_from_user
- (dev->dev_addr, ifr->ifr_data, sizeof(dev->dev_addr)))
- return -EFAULT;
- return 0;
-
- case SIOCGIFHWADDR:
- if (copy_to_user
- (ifr->ifr_data, dev->dev_addr, sizeof(dev->dev_addr)))
- return -EFAULT;
- return 0;
-
- case SIOCGMIIPHY:
- case SIOCGMIIREG:
- case SIOCSMIIREG:
- return phy_mii_ioctl(sp->phy_dev, data, cmd);
-
- default:
- break;
- }
-
- return -EOPNOTSUPP;
-}
-
-static void ar2313_adjust_link(struct net_device *dev)
-{
- struct ar2313_private *sp = netdev_priv(dev);
- unsigned int mc;
-
- if (!sp->phy_dev->link)
- return;
-
- if (sp->phy_dev->duplex != sp->oldduplex) {
- mc = readl(&sp->eth_regs->mac_control);
- mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
- if (sp->phy_dev->duplex)
- mc |= MAC_CONTROL_F;
- else
- mc |= MAC_CONTROL_DRO;
- writel(mc, &sp->eth_regs->mac_control);
- sp->oldduplex = sp->phy_dev->duplex;
- }
-}
-
-#define MII_ADDR(phy, reg) \
- ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
-
-static int
-mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
-{
- struct net_device *const dev = bus->priv;
- struct ar2313_private *sp = netdev_priv(dev);
- volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
-
- ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
- while (ethernet->mii_addr & MII_ADDR_BUSY);
- return (ethernet->mii_data >> MII_DATA_SHIFT);
-}
-
-static int
-mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
- u16 value)
-{
- struct net_device *const dev = bus->priv;
- struct ar2313_private *sp = netdev_priv(dev);
- volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
-
- while (ethernet->mii_addr & MII_ADDR_BUSY);
- ethernet->mii_data = value << MII_DATA_SHIFT;
- ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
-
- return 0;
-}
-
-static int mdiobus_reset(struct mii_bus *bus)
-{
- struct net_device *const dev = bus->priv;
-
- ar2313_reset_reg(dev);
-
- return 0;
-}
-
-static int mdiobus_probe (struct net_device *dev)
-{
- struct ar2313_private *const sp = netdev_priv(dev);
- struct phy_device *phydev = NULL;
- int phy_addr;
-
- /* find the first (lowest address) PHY on the current MAC's MII bus */
- for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
- if (sp->mii_bus.phy_map[phy_addr]) {
- phydev = sp->mii_bus.phy_map[phy_addr];
- break; /* break out with first one found */
- }
-
- if (!phydev) {
- printk (KERN_ERR "ar2313:%s: no PHY found\n", dev->name);
- return -1;
- }
-
- /* now we are supposed to have a proper phydev, to attach to... */
- BUG_ON(!phydev);
- BUG_ON(phydev->attached_dev);
-
- phydev = phy_connect(dev, phydev->dev.bus_id, &ar2313_adjust_link, 0,
- PHY_INTERFACE_MODE_MII);
-
- if (IS_ERR(phydev)) {
- printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
- return PTR_ERR(phydev);
- }
-
- /* mask with MAC supported features */
- phydev->supported &= (SUPPORTED_10baseT_Half
- | SUPPORTED_10baseT_Full
- | SUPPORTED_100baseT_Half
- | SUPPORTED_100baseT_Full
- | SUPPORTED_Autoneg
- /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
- | SUPPORTED_MII
- | SUPPORTED_TP);
-
- phydev->advertising = phydev->supported;
-
- sp->oldduplex = -1;
- sp->phy_dev = phydev;
-
- printk(KERN_INFO "%s: attached PHY driver [%s] "
- "(mii_bus:phy_addr=%s)\n",
- dev->name, phydev->drv->name, phydev->dev.bus_id);
-
- return 0;
-}
-
+++ /dev/null
-#ifndef _AR2313_H_
-#define _AR2313_H_
-
-#include <linux/autoconf.h>
-#include <asm/bootinfo.h>
-#include <ar531x_platform.h>
-
-/*
- * probe link timer - 5 secs
- */
-#define LINK_TIMER (5*HZ)
-
-#define IS_DMA_TX_INT(X) (((X) & (DMA_STATUS_TI)) != 0)
-#define IS_DMA_RX_INT(X) (((X) & (DMA_STATUS_RI)) != 0)
-#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN)) == 0)
-
-#define AR2313_TX_TIMEOUT (HZ/4)
-
-/*
- * Rings
- */
-#define DSC_RING_ENTRIES_SIZE (AR2313_DESCR_ENTRIES * sizeof(struct desc))
-#define DSC_NEXT(idx) ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
-
-static inline int tx_space(u32 csm, u32 prd)
-{
- return (csm - prd - 1) & (AR2313_DESCR_ENTRIES - 1);
-}
-
-#if MAX_SKB_FRAGS
-#define TX_RESERVED (MAX_SKB_FRAGS+1) /* +1 for message header */
-#define tx_ring_full(csm, prd) (tx_space(csm, prd) <= TX_RESERVED)
-#else
-#define tx_ring_full 0
-#endif
-
-#define AR2313_MBGET 2
-#define AR2313_MBSET 3
-#define AR2313_PCI_RECONFIG 4
-#define AR2313_PCI_DUMP 5
-#define AR2313_TEST_PANIC 6
-#define AR2313_TEST_NULLPTR 7
-#define AR2313_READ_DATA 8
-#define AR2313_WRITE_DATA 9
-#define AR2313_GET_VERSION 10
-#define AR2313_TEST_HANG 11
-#define AR2313_SYNC 12
-
-
-//
-// New Combo structure for Both Eth0 AND eth1
-//
-typedef struct {
- volatile unsigned int mac_control; /* 0x00 */
- volatile unsigned int mac_addr[2]; /* 0x04 - 0x08 */
- volatile unsigned int mcast_table[2]; /* 0x0c - 0x10 */
- volatile unsigned int mii_addr; /* 0x14 */
- volatile unsigned int mii_data; /* 0x18 */
- volatile unsigned int flow_control; /* 0x1c */
- volatile unsigned int vlan_tag; /* 0x20 */
- volatile unsigned int pad[7]; /* 0x24 - 0x3c */
- volatile unsigned int ucast_table[8]; /* 0x40-0x5c */
-
-} ETHERNET_STRUCT;
-
-/********************************************************************
- * Interrupt controller
- ********************************************************************/
-
-typedef struct {
- volatile unsigned int wdog_control; /* 0x08 */
- volatile unsigned int wdog_timer; /* 0x0c */
- volatile unsigned int misc_status; /* 0x10 */
- volatile unsigned int misc_mask; /* 0x14 */
- volatile unsigned int global_status; /* 0x18 */
- volatile unsigned int reserved; /* 0x1c */
- volatile unsigned int reset_control; /* 0x20 */
-} INTERRUPT;
-
-/********************************************************************
- * DMA controller
- ********************************************************************/
-typedef struct {
- volatile unsigned int bus_mode; /* 0x00 (CSR0) */
- volatile unsigned int xmt_poll; /* 0x04 (CSR1) */
- volatile unsigned int rcv_poll; /* 0x08 (CSR2) */
- volatile unsigned int rcv_base; /* 0x0c (CSR3) */
- volatile unsigned int xmt_base; /* 0x10 (CSR4) */
- volatile unsigned int status; /* 0x14 (CSR5) */
- volatile unsigned int control; /* 0x18 (CSR6) */
- volatile unsigned int intr_ena; /* 0x1c (CSR7) */
- volatile unsigned int rcv_missed; /* 0x20 (CSR8) */
- volatile unsigned int reserved[11]; /* 0x24-0x4c (CSR9-19) */
- volatile unsigned int cur_tx_buf_addr; /* 0x50 (CSR20) */
- volatile unsigned int cur_rx_buf_addr; /* 0x50 (CSR21) */
-} DMA;
-
-/*
- * Struct private for the Sibyte.
- *
- * Elements are grouped so variables used by the tx handling goes
- * together, and will go into the same cache lines etc. in order to
- * avoid cache line contention between the rx and tx handling on SMP.
- *
- * Frequently accessed variables are put at the beginning of the
- * struct to help the compiler generate better/shorter code.
- */
-struct ar2313_private {
- struct net_device *dev;
- int version;
- u32 mb[2];
-
- volatile ETHERNET_STRUCT *phy_regs;
- volatile ETHERNET_STRUCT *eth_regs;
- volatile DMA *dma_regs;
- volatile u32 *int_regs;
- struct ar531x_eth *cfg;
-
- spinlock_t lock; /* Serialise access to device */
-
- /*
- * RX and TX descriptors, must be adjacent
- */
- ar2313_descr_t *rx_ring;
- ar2313_descr_t *tx_ring;
-
-
- struct sk_buff **rx_skb;
- struct sk_buff **tx_skb;
-
- /*
- * RX elements
- */
- u32 rx_skbprd;
- u32 cur_rx;
-
- /*
- * TX elements
- */
- u32 tx_prd;
- u32 tx_csm;
-
- /*
- * Misc elements
- */
- int board_idx;
- char name[48];
- struct {
- u32 address;
- u32 length;
- char *mapping;
- } desc;
-
-
- struct timer_list link_timer;
- unsigned short phy; /* merlot phy = 1, samsung phy = 0x1f */
- unsigned short mac;
- unsigned short link; /* 0 - link down, 1 - link up */
- u16 phyData;
-
- struct tasklet_struct rx_tasklet;
- int unloading;
-
- struct phy_device *phy_dev;
- struct mii_bus mii_bus;
- int oldduplex;
-};
-
-
-/*
- * Prototypes
- */
-static int ar2313_init(struct net_device *dev);
-#ifdef TX_TIMEOUT
-static void ar2313_tx_timeout(struct net_device *dev);
-#endif
-#if 0
-static void ar2313_multicast_list(struct net_device *dev);
-#endif
-static int ar2313_restart(struct net_device *dev);
-#if DEBUG
-static void ar2313_dump_regs(struct net_device *dev);
-#endif
-static void ar2313_load_rx_ring(struct net_device *dev, int bufs);
-static irqreturn_t ar2313_interrupt(int irq, void *dev_id);
-static int ar2313_open(struct net_device *dev);
-static int ar2313_start_xmit(struct sk_buff *skb, struct net_device *dev);
-static int ar2313_close(struct net_device *dev);
-static int ar2313_ioctl(struct net_device *dev, struct ifreq *ifr,
- int cmd);
-static void ar2313_init_cleanup(struct net_device *dev);
-static int ar2313_setup_timer(struct net_device *dev);
-static void ar2313_link_timer_fn(unsigned long data);
-static void ar2313_check_link(struct net_device *dev);
-#endif /* _AR2313_H_ */
+++ /dev/null
-#ifndef __ARUBA_DMA_H__
-#define __ARUBA_DMA_H__
-
-/*******************************************************************************
- *
- * Copyright 2002 Integrated Device Technology, Inc.
- * All rights reserved.
- *
- * DMA register definition.
- *
- * File : $Id: dma.h,v 1.3 2002/06/06 18:34:03 astichte Exp $
- *
- * Author : ryan.holmQVist@idt.com
- * Date : 20011005
- * Update :
- * $Log: dma.h,v $
- * Revision 1.3 2002/06/06 18:34:03 astichte
- * Added XXX_PhysicalAddress and XXX_VirtualAddress
- *
- * Revision 1.2 2002/06/05 18:30:46 astichte
- * Removed IDTField
- *
- * Revision 1.1 2002/05/29 17:33:21 sysarch
- * jba File moved from vcode/include/idt/acacia
- *
- *
- ******************************************************************************/
-
-#define AR_BIT(x) (1 << (x))
-#define DMA_RX_ERR_CRC AR_BIT(1)
-#define DMA_RX_ERR_DRIB AR_BIT(2)
-#define DMA_RX_ERR_MII AR_BIT(3)
-#define DMA_RX_EV2 AR_BIT(5)
-#define DMA_RX_ERR_COL AR_BIT(6)
-#define DMA_RX_LONG AR_BIT(7)
-#define DMA_RX_LS AR_BIT(8) /* last descriptor */
-#define DMA_RX_FS AR_BIT(9) /* first descriptor */
-#define DMA_RX_MF AR_BIT(10) /* multicast frame */
-#define DMA_RX_ERR_RUNT AR_BIT(11) /* runt frame */
-#define DMA_RX_ERR_LENGTH AR_BIT(12) /* length error */
-#define DMA_RX_ERR_DESC AR_BIT(14) /* descriptor error */
-#define DMA_RX_ERROR AR_BIT(15) /* error summary */
-#define DMA_RX_LEN_MASK 0x3fff0000
-#define DMA_RX_LEN_SHIFT 16
-#define DMA_RX_FILT AR_BIT(30)
-#define DMA_RX_OWN AR_BIT(31) /* desc owned by DMA controller */
-
-#define DMA_RX1_BSIZE_MASK 0x000007ff
-#define DMA_RX1_BSIZE_SHIFT 0
-#define DMA_RX1_CHAINED AR_BIT(24)
-#define DMA_RX1_RER AR_BIT(25)
-
-#define DMA_TX_ERR_UNDER AR_BIT(1) /* underflow error */
-#define DMA_TX_ERR_DEFER AR_BIT(2) /* excessive deferral */
-#define DMA_TX_COL_MASK 0x78
-#define DMA_TX_COL_SHIFT 3
-#define DMA_TX_ERR_HB AR_BIT(7) /* hearbeat failure */
-#define DMA_TX_ERR_COL AR_BIT(8) /* excessive collisions */
-#define DMA_TX_ERR_LATE AR_BIT(9) /* late collision */
-#define DMA_TX_ERR_LINK AR_BIT(10) /* no carrier */
-#define DMA_TX_ERR_LOSS AR_BIT(11) /* loss of carrier */
-#define DMA_TX_ERR_JABBER AR_BIT(14) /* transmit jabber timeout */
-#define DMA_TX_ERROR AR_BIT(15) /* frame aborted */
-#define DMA_TX_OWN AR_BIT(31) /* descr owned by DMA controller */
-
-#define DMA_TX1_BSIZE_MASK 0x000007ff
-#define DMA_TX1_BSIZE_SHIFT 0
-#define DMA_TX1_CHAINED AR_BIT(24) /* chained descriptors */
-#define DMA_TX1_TER AR_BIT(25) /* transmit end of ring */
-#define DMA_TX1_FS AR_BIT(29) /* first segment */
-#define DMA_TX1_LS AR_BIT(30) /* last segment */
-#define DMA_TX1_IC AR_BIT(31) /* interrupt on completion */
-
-#define RCVPKT_LENGTH(X) (X >> 16) /* Received pkt Length */
-
-#define MAC_CONTROL_RE AR_BIT(2) /* receive enable */
-#define MAC_CONTROL_TE AR_BIT(3) /* transmit enable */
-#define MAC_CONTROL_DC AR_BIT(5) /* Deferral check */
-#define MAC_CONTROL_ASTP AR_BIT(8) /* Auto pad strip */
-#define MAC_CONTROL_DRTY AR_BIT(10) /* Disable retry */
-#define MAC_CONTROL_DBF AR_BIT(11) /* Disable bcast frames */
-#define MAC_CONTROL_LCC AR_BIT(12) /* late collision ctrl */
-#define MAC_CONTROL_HP AR_BIT(13) /* Hash Perfect filtering */
-#define MAC_CONTROL_HASH AR_BIT(14) /* Unicast hash filtering */
-#define MAC_CONTROL_HO AR_BIT(15) /* Hash only filtering */
-#define MAC_CONTROL_PB AR_BIT(16) /* Pass Bad frames */
-#define MAC_CONTROL_IF AR_BIT(17) /* Inverse filtering */
-#define MAC_CONTROL_PR AR_BIT(18) /* promiscuous mode (valid frames
- only) */
-#define MAC_CONTROL_PM AR_BIT(19) /* pass multicast */
-#define MAC_CONTROL_F AR_BIT(20) /* full-duplex */
-#define MAC_CONTROL_DRO AR_BIT(23) /* Disable Receive Own */
-#define MAC_CONTROL_HBD AR_BIT(28) /* heart-beat disabled (MUST BE
- SET) */
-#define MAC_CONTROL_BLE AR_BIT(30) /* big endian mode */
-#define MAC_CONTROL_RA AR_BIT(31) /* receive all (valid and invalid
- frames) */
-
-#define MII_ADDR_BUSY AR_BIT(0)
-#define MII_ADDR_WRITE AR_BIT(1)
-#define MII_ADDR_REG_SHIFT 6
-#define MII_ADDR_PHY_SHIFT 11
-#define MII_DATA_SHIFT 0
-
-#define FLOW_CONTROL_FCE AR_BIT(1)
-
-#define DMA_BUS_MODE_SWR AR_BIT(0) /* software reset */
-#define DMA_BUS_MODE_BLE AR_BIT(7) /* big endian mode */
-#define DMA_BUS_MODE_PBL_SHIFT 8 /* programmable burst length 32 */
-#define DMA_BUS_MODE_DBO AR_BIT(20) /* big-endian descriptors */
-
-#define DMA_STATUS_TI AR_BIT(0) /* transmit interrupt */
-#define DMA_STATUS_TPS AR_BIT(1) /* transmit process stopped */
-#define DMA_STATUS_TU AR_BIT(2) /* transmit buffer unavailable */
-#define DMA_STATUS_TJT AR_BIT(3) /* transmit buffer timeout */
-#define DMA_STATUS_UNF AR_BIT(5) /* transmit underflow */
-#define DMA_STATUS_RI AR_BIT(6) /* receive interrupt */
-#define DMA_STATUS_RU AR_BIT(7) /* receive buffer unavailable */
-#define DMA_STATUS_RPS AR_BIT(8) /* receive process stopped */
-#define DMA_STATUS_ETI AR_BIT(10) /* early transmit interrupt */
-#define DMA_STATUS_FBE AR_BIT(13) /* fatal bus interrupt */
-#define DMA_STATUS_ERI AR_BIT(14) /* early receive interrupt */
-#define DMA_STATUS_AIS AR_BIT(15) /* abnormal interrupt summary */
-#define DMA_STATUS_NIS AR_BIT(16) /* normal interrupt summary */
-#define DMA_STATUS_RS_SHIFT 17 /* receive process state */
-#define DMA_STATUS_TS_SHIFT 20 /* transmit process state */
-#define DMA_STATUS_EB_SHIFT 23 /* error bits */
-
-#define DMA_CONTROL_SR AR_BIT(1) /* start receive */
-#define DMA_CONTROL_ST AR_BIT(13) /* start transmit */
-#define DMA_CONTROL_SF AR_BIT(21) /* store and forward */
-
-
-typedef struct {
- volatile unsigned int status; // OWN, Device control and status.
- volatile unsigned int devcs; // pkt Control bits + Length
- volatile unsigned int addr; // Current Address.
- volatile unsigned int descr; // Next descriptor in chain.
-} ar2313_descr_t;
-
-
-#endif // __ARUBA_DMA_H__
+++ /dev/null
-/*
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Copyright (C) 2008 John Crispin <blogic@openwrt.org>
- * Based on EP93xx and ifxmips wdt driver
- */
-
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/types.h>
-#include <linux/miscdevice.h>
-#include <linux/watchdog.h>
-#include <linux/fs.h>
-#include <linux/ioport.h>
-#include <linux/notifier.h>
-#include <linux/reboot.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <asm/system.h>
-#include <asm/addrspace.h>
-#include <ar531x.h>
-
-#define CLOCK_RATE 40000000
-#define HEARTBEAT(x) (x < 1 || x > 90)?(20):(x)
-
-static int wdt_timeout = 20;
-static int started = 0;
-static int in_use = 0;
-
-static void
-ar2315_wdt_enable(void)
-{
- sysRegWrite(AR5315_WD, wdt_timeout * CLOCK_RATE);
- sysRegWrite(AR5315_ISR, 0x80);
-}
-
-static ssize_t
-ar2315_wdt_write(struct file *file, const char __user *data, size_t len, loff_t *ppos)
-{
- if(len)
- ar2315_wdt_enable();
- return len;
-}
-
-static int
-ar2315_wdt_open(struct inode *inode, struct file *file)
-{
- if(in_use)
- return -EBUSY;
- ar2315_wdt_enable();
- in_use = started = 1;
- return nonseekable_open(inode, file);
-}
-
-static int
-ar2315_wdt_release(struct inode *inode, struct file *file)
-{
- in_use = 0;
- return 0;
-}
-
-static irqreturn_t
-ar2315_wdt_interrupt(int irq, void *dev_id)
-{
- if(started)
- {
- printk(KERN_CRIT "watchdog expired, rebooting system\n");
- emergency_restart();
- } else {
- sysRegWrite(AR5315_WDC, 0);
- sysRegWrite(AR5315_WD, 0);
- sysRegWrite(AR5315_ISR, 0x80);
- }
- return IRQ_HANDLED;
-}
-
-static struct watchdog_info ident = {
- .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
- .identity = "ar2315 Watchdog",
-};
-
-static int
-ar2315_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
-{
- int new_wdt_timeout;
- int ret = -ENOIOCTLCMD;
-
- switch(cmd)
- {
- case WDIOC_GETSUPPORT:
- ret = copy_to_user((struct watchdog_info __user *)arg, &ident, sizeof(ident)) ? -EFAULT : 0;
- break;
-
- case WDIOC_KEEPALIVE:
- ar2315_wdt_enable();
- ret = 0;
- break;
-
- case WDIOC_SETTIMEOUT:
- if((ret = get_user(new_wdt_timeout, (int __user *)arg)))
- break;
- wdt_timeout = HEARTBEAT(new_wdt_timeout);
- ar2315_wdt_enable();
- break;
-
- case WDIOC_GETTIMEOUT:
- ret = put_user(wdt_timeout, (int __user *)arg);
- break;
- }
- return ret;
-}
-
-static struct file_operations ar2315_wdt_fops = {
- .owner = THIS_MODULE,
- .llseek = no_llseek,
- .write = ar2315_wdt_write,
- .ioctl = ar2315_wdt_ioctl,
- .open = ar2315_wdt_open,
- .release = ar2315_wdt_release,
-};
-
-static struct miscdevice ar2315_wdt_miscdev = {
- .minor = WATCHDOG_MINOR,
- .name = "watchdog",
- .fops = &ar2315_wdt_fops,
-};
-
-static int
-ar2315_wdt_probe(struct platform_device *dev)
-{
- int ret = 0;
-
- ar2315_wdt_enable();
- ret = request_irq(AR531X_MISC_IRQ_WATCHDOG, ar2315_wdt_interrupt, IRQF_DISABLED, "ar2315_wdt", NULL);
- if(ret)
- {
- printk(KERN_ERR "ar2315wdt: failed to register inetrrupt\n");
- goto out;
- }
-
- ret = misc_register(&ar2315_wdt_miscdev);
- if(ret)
- printk(KERN_ERR "ar2315wdt: failed to register miscdev\n");
-
-out:
- return ret;
-}
-
-static int
-ar2315_wdt_remove(struct platform_device *dev)
-{
- misc_deregister(&ar2315_wdt_miscdev);
- free_irq(AR531X_MISC_IRQ_WATCHDOG, NULL);
- return 0;
-}
-
-static struct platform_driver ar2315_wdt_driver = {
- .probe = ar2315_wdt_probe,
- .remove = ar2315_wdt_remove,
- .driver = {
- .name = "ar2315_wdt",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init
-init_ar2315_wdt(void)
-{
- int ret = platform_driver_register(&ar2315_wdt_driver);
- if(ret)
- printk(KERN_INFO "ar2315_wdt: error registering platfom driver!");
- return ret;
-}
-
-static void __exit
-exit_ar2315_wdt(void)
-{
- platform_driver_unregister(&ar2315_wdt_driver);
-}
-
-module_init(init_ar2315_wdt);
-module_exit(exit_ar2315_wdt);
--- /dev/null
+Allow boards to provide their own function for reading the timer IRQ number
+
+Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
+
+--- a/arch/mips/kernel/traps.c
++++ b/arch/mips/kernel/traps.c
+@@ -47,6 +47,7 @@
+ #include <asm/mmu_context.h>
+ #include <asm/types.h>
+ #include <asm/stacktrace.h>
++#include <asm/time.h>
+
+ extern void check_wait(void);
+ extern asmlinkage void r4k_wait(void);
+@@ -1514,6 +1515,8 @@ void __cpuinit per_cpu_trap_init(void)
+ */
+ if (cpu_has_mips_r2) {
+ cp0_compare_irq = (read_c0_intctl() >> 29) & 7;
++ if (get_c0_compare_irq)
++ cp0_compare_irq = get_c0_compare_irq();
+ cp0_perfcount_irq = (read_c0_intctl() >> 26) & 7;
+ if (cp0_perfcount_irq == cp0_compare_irq)
+ cp0_perfcount_irq = -1;
+--- a/arch/mips/include/asm/time.h
++++ b/arch/mips/include/asm/time.h
+@@ -53,6 +53,7 @@ extern int (*perf_irq)(void);
+ #ifdef CONFIG_CEVT_R4K
+ extern int mips_clockevent_init(void);
+ extern unsigned int __weak get_c0_compare_int(void);
++extern unsigned int __weak get_c0_compare_irq(void);
+ #else
+ static inline int mips_clockevent_init(void)
+ {
+
--- /dev/null
+--- a/arch/mips/kernel/cevt-r4k.c
++++ b/arch/mips/kernel/cevt-r4k.c
+@@ -15,6 +15,22 @@
+ #include <asm/cevt-r4k.h>
+
+ /*
++ * Compare interrupt can be routed and latched outside the core,
++ * so a single execution hazard barrier may not be enough to give
++ * it time to clear as seen in the Cause register. 4 time the
++ * pipeline depth seems reasonably conservative, and empirically
++ * works better in configurations with high CPU/bus clock ratios.
++ */
++
++#define compare_change_hazard() \
++ do { \
++ irq_disable_hazard(); \
++ irq_disable_hazard(); \
++ irq_disable_hazard(); \
++ irq_disable_hazard(); \
++ } while (0)
++
++/*
+ * The SMTC Kernel for the 34K, 1004K, et. al. replaces several
+ * of these routines with SMTC-specific variants.
+ */
+@@ -30,6 +46,7 @@ static int mips_next_event(unsigned long
+ cnt = read_c0_count();
+ cnt += delta;
+ write_c0_compare(cnt);
++ compare_change_hazard();
+ res = ((int)(read_c0_count() - cnt) > 0) ? -ETIME : 0;
+ return res;
+ }
+@@ -99,22 +116,6 @@ static int c0_compare_int_pending(void)
+ return (read_c0_cause() >> cp0_compare_irq) & 0x100;
+ }
+
+-/*
+- * Compare interrupt can be routed and latched outside the core,
+- * so a single execution hazard barrier may not be enough to give
+- * it time to clear as seen in the Cause register. 4 time the
+- * pipeline depth seems reasonably conservative, and empirically
+- * works better in configurations with high CPU/bus clock ratios.
+- */
+-
+-#define compare_change_hazard() \
+- do { \
+- irq_disable_hazard(); \
+- irq_disable_hazard(); \
+- irq_disable_hazard(); \
+- irq_disable_hazard(); \
+- } while (0)
+-
+ int c0_compare_int_usable(void)
+ {
+ unsigned int delta;
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
-@@ -60,6 +60,18 @@ config BCM47XX
+@@ -60,6 +60,19 @@ config BCM47XX
help
Support for BCM47XX based boards
+config ATHEROS
-+ bool "Atheros SoC support (EXPERIMENTAL)"
-+ depends on EXPERIMENTAL
-+ select DMA_NONCOHERENT
++ bool "Atheros 231x/531x SoC support"
+ select CEVT_R4K
+ select CSRC_R4K
++ select DMA_NONCOHERENT
+ select IRQ_CPU
+ select SYS_HAS_CPU_MIPS32_R1
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select GENERIC_GPIO
++ help
++ Support for AR231x and AR531x based boards
+
config MIPS_COBALT
bool "Cobalt Server"
select CEVT_R4K
-@@ -597,6 +609,7 @@ config WR_PPMC
+@@ -597,6 +610,7 @@ config WR_PPMC
endchoice
-+source "arch/mips/atheros/Kconfig"
++source "arch/mips/ar231x/Kconfig"
source "arch/mips/alchemy/Kconfig"
source "arch/mips/basler/excite/Kconfig"
source "arch/mips/emma/Kconfig"
#
+# Atheros AR5312/AR2312 WiSoC
+#
-+core-$(CONFIG_ATHEROS) += arch/mips/atheros/
-+cflags-$(CONFIG_ATHEROS) += -I$(srctree)/arch/mips/include/asm/mach-atheros
++core-$(CONFIG_ATHEROS) += arch/mips/ar231x/
++cflags-$(CONFIG_ATHEROS) += -I$(srctree)/arch/mips/include/asm/mach-ar231x
+load-$(CONFIG_ATHEROS) += 0xffffffff80041000
+
+#
# Cobalt Server
#
core-$(CONFIG_MIPS_COBALT) += arch/mips/cobalt/
---- a/arch/mips/include/asm/bootinfo.h
-+++ b/arch/mips/include/asm/bootinfo.h
-@@ -57,6 +57,18 @@
- #define MACH_MIKROTIK_RB532 0 /* Mikrotik RouterBoard 532 */
- #define MACH_MIKROTIK_RB532A 1 /* Mikrotik RouterBoard 532A */
-
+--- /dev/null
++++ b/arch/mips/ar231x/Kconfig
+@@ -0,0 +1,27 @@
++config ATHEROS_AR5312
++ bool "Atheros 5312/2312+ support"
++ depends on ATHEROS
++ default y
++
++config ATHEROS_AR2315
++ bool "Atheros 2315+ support"
++ depends on ATHEROS
++ select DMA_NONCOHERENT
++ select CEVT_R4K
++ select CSRC_R4K
++ select IRQ_CPU
++ select SYS_HAS_CPU_MIPS32_R1
++ select SYS_SUPPORTS_32BIT_KERNEL
++ select SYS_SUPPORTS_BIG_ENDIAN
++ select GENERIC_GPIO
++ default y
++
++config ATHEROS_AR2315_PCI
++ bool "PCI support"
++ depends on ATHEROS_AR2315
++ select HW_HAS_PCI
++ select PCI
++ select USB_ARCH_HAS_HCD
++ select USB_ARCH_HAS_OHCI
++ select USB_ARCH_HAS_EHCI
++ default y
+--- /dev/null
++++ b/arch/mips/ar231x/Makefile
+@@ -0,0 +1,14 @@
++#
++# This file is subject to the terms and conditions of the GNU General Public
++# License. See the file "COPYING" in the main directory of this archive
++# for more details.
++#
++# Copyright (C) 2006 FON Technology, SL.
++# Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++# Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++#
++
++obj-y += board.o prom.o devices.o
++obj-$(CONFIG_ATHEROS_AR5312) += ar5312.o
++obj-$(CONFIG_ATHEROS_AR2315) += ar2315.o
++obj-$(CONFIG_ATHEROS_AR2315_PCI) += pci.o
+--- /dev/null
++++ b/arch/mips/ar231x/board.c
+@@ -0,0 +1,247 @@
+/*
-+ * Valid machtype for group ATHEROS
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
+ */
-+#define MACH_GROUP_ATHEROS 26
-+#define MACH_ATHEROS_AR5312 0
-+#define MACH_ATHEROS_AR2312 1
-+#define MACH_ATHEROS_AR2313 2
-+#define MACH_ATHEROS_AR2315 3
-+#define MACH_ATHEROS_AR2316 4
-+#define MACH_ATHEROS_AR2317 5
-+#define MACH_ATHEROS_AR2318 6
+
- #define CL_SIZE COMMAND_LINE_SIZE
-
- extern char *system_type;
++#include <linux/autoconf.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/types.h>
++#include <linux/string.h>
++#include <linux/platform_device.h>
++#include <linux/kernel.h>
++#include <linux/random.h>
++#include <linux/etherdevice.h>
++#include <asm/irq_cpu.h>
++#include <asm/reboot.h>
++#include <asm/io.h>
++
++#include <ar231x_platform.h>
++#include "devices.h"
++#include "ar5312.h"
++#include "ar2315.h"
++
++void (*ar231x_irq_dispatch)(void);
++
++static inline bool
++check_radio_magic(u8 *addr)
++{
++ addr += 0x7a; /* offset for flash magic */
++ if ((addr[0] == 0x5a) && (addr[1] == 0xa5)) {
++ return 1;
++ }
++ return 0;
++}
++
++static inline bool
++check_board_data(u8 *flash_limit, u8 *addr, bool broken)
++{
++ /* config magic found */
++ if (*((u32 *)addr) == AR531X_BD_MAGIC)
++ return 1;
++
++ if (!broken)
++ return 0;
++
++ if (check_radio_magic(addr + 0xf8))
++ ar231x_board.radio = addr + 0xf8;
++ if ((addr < flash_limit + 0x10000) &&
++ check_radio_magic(addr + 0x10000))
++ ar231x_board.radio = addr + 0x10000;
++
++ if (ar231x_board.radio) {
++ /* broken board data detected, use radio data to find the offset,
++ * user will fix this */
++ return 1;
++ }
++ return 0;
++}
++
++static u8 *
++find_board_config(u8 *flash_limit, bool broken)
++{
++ u8 *addr;
++ int found = 0;
++
++ for (addr = flash_limit - 0x1000;
++ addr >= flash_limit - 0x30000;
++ addr -= 0x1000) {
++
++ if (check_board_data(flash_limit, addr, broken)) {
++ found = 1;
++ break;
++ }
++ }
++
++ if (!found)
++ addr = NULL;
++
++ return addr;
++}
++
++static u8 *
++find_radio_config(u8 *flash_limit, u8 *board_config)
++{
++ int found;
++ u8 *radio_config;
++
++ /*
++ * Now find the start of Radio Configuration data, using heuristics:
++ * Search forward from Board Configuration data by 0x1000 bytes
++ * at a time until we find non-0xffffffff.
++ */
++ found = 0;
++ for (radio_config = board_config + 0x1000;
++ (radio_config < flash_limit);
++ radio_config += 0x1000) {
++ if ((*(u32 *)radio_config != 0xffffffff) &&
++ check_radio_magic(radio_config)) {
++ found = 1;
++ break;
++ }
++ }
++
++ /* AR2316 relocates radio config to new location */
++ if (!found) {
++ for (radio_config = board_config + 0xf8;
++ (radio_config < flash_limit - 0x1000 + 0xf8);
++ radio_config += 0x1000) {
++ if ((*(u32 *)radio_config != 0xffffffff) &&
++ check_radio_magic(radio_config)) {
++ found = 1;
++ break;
++ }
++ }
++ }
++
++ if (!found) {
++ printk("Could not find Radio Configuration data\n");
++ radio_config = 0;
++ }
++
++ return (u8 *) radio_config;
++}
++
++int __init
++ar231x_find_config(u8 *flash_limit)
++{
++ struct ar231x_boarddata *config;
++ unsigned int rcfg_size;
++ int broken_boarddata = 0;
++ u8 *bcfg, *rcfg;
++ u8 *board_data;
++ u8 *radio_data;
++ u32 offset;
++
++ ar231x_board.config = NULL;
++ ar231x_board.radio = NULL;
++ /* Copy the board and radio data to RAM, because accessing the mapped
++ * memory of the flash directly after booting is not safe */
++
++ /* Try to find valid board and radio data */
++ bcfg = find_board_config(flash_limit, false);
++
++ /* If that fails, try to at least find valid radio data */
++ if (!bcfg) {
++ bcfg = find_board_config(flash_limit, true);
++ broken_boarddata = 1;
++ }
++
++ if (!bcfg) {
++ printk(KERN_WARNING "WARNING: No board configuration data found!\n");
++ return -ENODEV;
++ }
++
++ board_data = kzalloc(BOARD_CONFIG_BUFSZ, GFP_KERNEL);
++ ar231x_board.config = (struct ar231x_boarddata *) board_data;
++ memcpy(board_data, bcfg, 0x100);
++ if (broken_boarddata) {
++ printk(KERN_WARNING "WARNING: broken board data detected\n");
++ config = ar231x_board.config;
++ if (!memcmp(config->enet0_mac, "\x00\x00\x00\x00\x00\x00", 6)) {
++ printk(KERN_INFO "Fixing up empty mac addresses\n");
++ random_ether_addr(config->enet0_mac);
++ random_ether_addr(config->enet1_mac);
++ }
++ }
++
++
++ /* Radio config starts 0x100 bytes after board config, regardless
++ * of what the physical layout on the flash chip looks like */
++
++ if (ar231x_board.radio)
++ rcfg = (u8 *) ar231x_board.radio;
++ else
++ rcfg = find_radio_config(flash_limit, bcfg);
++
++ if (!rcfg)
++ return -ENODEV;
++
++ radio_data = board_data + 0x100 + ((rcfg - bcfg) & 0xfff);
++ ar231x_board.radio = radio_data;
++ offset = radio_data - board_data;
++ printk(KERN_INFO "Radio config found at offset 0x%x(0x%x)\n", rcfg - bcfg, offset);
++ rcfg_size = BOARD_CONFIG_BUFSZ - offset;
++ memcpy(radio_data, rcfg, rcfg_size);
++
++ return 0;
++}
++
++static void
++ar231x_halt(void)
++{
++ local_irq_disable();
++ while (1);
++}
++
++void __init
++plat_mem_setup(void)
++{
++ _machine_halt = ar231x_halt;
++ pm_power_off = ar231x_halt;
++
++ ar5312_plat_setup();
++ ar2315_plat_setup();
++
++ /* Disable data watchpoints */
++ write_c0_watchlo0(0);
++}
++
++
++asmlinkage void
++plat_irq_dispatch(void)
++{
++ ar231x_irq_dispatch();
++}
++
++void __init
++plat_time_init(void)
++{
++ ar5312_time_init();
++ ar2315_time_init();
++}
++
++unsigned int __cpuinit
++get_c0_compare_irq(void)
++{
++ return CP0_LEGACY_COMPARE_IRQ;
++}
++
++void __init
++arch_init_irq(void)
++{
++ clear_c0_status(ST0_IM);
++ mips_cpu_irq_init();
++
++ /* Initialize interrupt controllers */
++ ar5312_irq_init();
++ ar2315_irq_init();
++}
++
++
+--- /dev/null
++++ b/arch/mips/ar231x/prom.c
+@@ -0,0 +1,37 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright MontaVista Software Inc
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
++ */
++
++/*
++ * Prom setup file for ar531x
++ */
++
++#include <linux/init.h>
++#include <linux/autoconf.h>
++#include <linux/kernel.h>
++#include <linux/string.h>
++#include <linux/mm.h>
++#include <linux/bootmem.h>
++
++#include <asm/bootinfo.h>
++#include <asm/addrspace.h>
++#include "ar5312.h"
++#include "ar2315.h"
++
++void __init prom_init(void)
++{
++ ar5312_prom_init();
++ ar2315_prom_init();
++}
++
++void __init prom_free_prom_memory(void)
++{
++}
+--- /dev/null
++++ b/arch/mips/ar231x/reset.c
+@@ -0,0 +1,162 @@
++#include <linux/module.h>
++#include <linux/timer.h>
++#include <linux/interrupt.h>
++#include <linux/kobject.h>
++#include <linux/workqueue.h>
++#include <linux/skbuff.h>
++#include <linux/netlink.h>
++#include <net/sock.h>
++#include <asm/uaccess.h>
++#include <ar231x.h>
++
++#define AR531X_RESET_GPIO_IRQ (AR531X_GPIO_IRQ(bcfg->resetConfigGpio))
++
++struct event_t {
++ struct work_struct wq;
++ int set;
++ unsigned long jiffies;
++};
++
++static struct ar231x_boarddata *bcfg;
++static struct timer_list rst_button_timer;
++
++extern struct sock *uevent_sock;
++extern u64 uevent_next_seqnum(void);
++static unsigned long seen;
++
++static inline void add_msg(struct sk_buff *skb, char *msg)
++{
++ char *scratch;
++ scratch = skb_put(skb, strlen(msg) + 1);
++ sprintf(scratch, msg);
++}
++
++static void hotplug_button(struct work_struct *wq)
++{
++ struct sk_buff *skb;
++ struct event_t *event;
++ size_t len;
++ char *scratch, *s;
++ char buf[128];
++
++ event = container_of(wq, struct event_t, wq);
++ if (!uevent_sock)
++ goto done;
++
++ /* allocate message with the maximum possible size */
++ s = event->set ? "pressed" : "released";
++ len = strlen(s) + 2;
++ skb = alloc_skb(len + 2048, GFP_KERNEL);
++ if (!skb)
++ goto done;
++
++ /* add header */
++ scratch = skb_put(skb, len);
++ sprintf(scratch, "%s@",s);
++
++ /* copy keys to our continuous event payload buffer */
++ add_msg(skb, "HOME=/");
++ add_msg(skb, "PATH=/sbin:/bin:/usr/sbin:/usr/bin");
++ add_msg(skb, "SUBSYSTEM=button");
++ add_msg(skb, "BUTTON=reset");
++ add_msg(skb, (event->set ? "ACTION=pressed" : "ACTION=released"));
++ sprintf(buf, "SEEN=%ld", (event->jiffies - seen)/HZ);
++ add_msg(skb, buf);
++ snprintf(buf, 128, "SEQNUM=%llu", uevent_next_seqnum());
++ add_msg(skb, buf);
++
++ NETLINK_CB(skb).dst_group = 1;
++ netlink_broadcast(uevent_sock, skb, 0, 1, GFP_KERNEL);
++
++done:
++ kfree(event);
++}
++
++static int no_release_workaround = 1;
++
++static void
++reset_button_poll(unsigned long unused)
++{
++ struct event_t *event;
++ int gpio = ~0;
++
++ if(!no_release_workaround)
++ return;
++
++ DO_AR2315(gpio = sysRegRead(AR2315_GPIO_DI);)
++ gpio &= 1 << (AR531X_RESET_GPIO_IRQ - AR531X_GPIO_IRQ_BASE);
++ if(gpio)
++ {
++ rst_button_timer.expires = jiffies + (HZ / 4);
++ add_timer(&rst_button_timer);
++ } else {
++ event = (struct event_t *) kzalloc(sizeof(struct event_t), GFP_ATOMIC);
++ if (!event)
++ {
++ printk("Could not alloc hotplug event\n");
++ return;
++ }
++ event->set = 0;
++ event->jiffies = jiffies;
++ INIT_WORK(&event->wq, (void *)(void *)hotplug_button);
++ schedule_work(&event->wq);
++ }
++}
++
++static irqreturn_t button_handler(int irq, void *dev_id)
++{
++ static int pressed = 0;
++ struct event_t *event;
++ u32 gpio = ~0;
++
++ event = (struct event_t *) kzalloc(sizeof(struct event_t), GFP_ATOMIC);
++ if (!event)
++ return IRQ_NONE;
++
++ pressed = !pressed;
++
++ DO_AR2315(gpio = sysRegRead(AR2315_GPIO_DI);)
++ gpio &= 1 << (irq - AR531X_GPIO_IRQ_BASE);
++
++ event->set = gpio;
++ if(!event->set)
++ no_release_workaround = 0;
++
++ event->jiffies = jiffies;
++
++ INIT_WORK(&event->wq, (void *)(void *)hotplug_button);
++ schedule_work(&event->wq);
++
++ seen = jiffies;
++ if(event->set && no_release_workaround)
++ mod_timer(&rst_button_timer, jiffies + (HZ / 4));
++
++ return IRQ_HANDLED;
++}
++
++void ar231x_disable_reset_button(void)
++{
++ disable_irq(AR531X_RESET_GPIO_IRQ);
++}
++
++EXPORT_SYMBOL(ar231x_disable_reset_button);
++
++int __init ar231x_init_reset(void)
++{
++ bcfg = (struct ar231x_boarddata *) board_config;
++
++ seen = jiffies;
++
++ init_timer(&rst_button_timer);
++ rst_button_timer.function = reset_button_poll;
++ rst_button_timer.expires = jiffies + HZ / 50;
++ add_timer(&rst_button_timer);
++
++ request_irq(AR531X_RESET_GPIO_IRQ, &button_handler, IRQF_SAMPLE_RANDOM, "ar231x_reset", NULL);
++
++ return 0;
++}
++
++
++
++module_init(ar231x_init_reset);
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/ar231x_platform.h
+@@ -0,0 +1,83 @@
++#ifndef __AR531X_PLATFORM_H
++#define __AR531X_PLATFORM_H
++
++/*
++ * This is board-specific data that is stored in a "fixed" location in flash.
++ * It is shared across operating systems, so it should not be changed lightly.
++ * The main reason we need it is in order to extract the ethernet MAC
++ * address(es).
++ */
++struct ar231x_boarddata {
++ u32 magic; /* board data is valid */
++#define AR531X_BD_MAGIC 0x35333131 /* "5311", for all 531x platforms */
++ u16 cksum; /* checksum (starting with BD_REV 2) */
++ u16 rev; /* revision of this struct */
++#define BD_REV 4
++ char boardName[64]; /* Name of board */
++ u16 major; /* Board major number */
++ u16 minor; /* Board minor number */
++ u32 flags; /* Board configuration */
++#define BD_ENET0 0x00000001 /* ENET0 is stuffed */
++#define BD_ENET1 0x00000002 /* ENET1 is stuffed */
++#define BD_UART1 0x00000004 /* UART1 is stuffed */
++#define BD_UART0 0x00000008 /* UART0 is stuffed (dma) */
++#define BD_RSTFACTORY 0x00000010 /* Reset factory defaults stuffed */
++#define BD_SYSLED 0x00000020 /* System LED stuffed */
++#define BD_EXTUARTCLK 0x00000040 /* External UART clock */
++#define BD_CPUFREQ 0x00000080 /* cpu freq is valid in nvram */
++#define BD_SYSFREQ 0x00000100 /* sys freq is set in nvram */
++#define BD_WLAN0 0x00000200 /* Enable WLAN0 */
++#define BD_MEMCAP 0x00000400 /* CAP SDRAM @ memCap for testing */
++#define BD_DISWATCHDOG 0x00000800 /* disable system watchdog */
++#define BD_WLAN1 0x00001000 /* Enable WLAN1 (ar5212) */
++#define BD_ISCASPER 0x00002000 /* FLAG for AR2312 */
++#define BD_WLAN0_2G_EN 0x00004000 /* FLAG for radio0_2G */
++#define BD_WLAN0_5G_EN 0x00008000 /* FLAG for radio0_2G */
++#define BD_WLAN1_2G_EN 0x00020000 /* FLAG for radio0_2G */
++#define BD_WLAN1_5G_EN 0x00040000 /* FLAG for radio0_2G */
++ u16 resetConfigGpio; /* Reset factory GPIO pin */
++ u16 sysLedGpio; /* System LED GPIO pin */
++
++ u32 cpuFreq; /* CPU core frequency in Hz */
++ u32 sysFreq; /* System frequency in Hz */
++ u32 cntFreq; /* Calculated C0_COUNT frequency */
++
++ u8 wlan0_mac[6];
++ u8 enet0_mac[6];
++ u8 enet1_mac[6];
++
++ u16 pciId; /* Pseudo PCIID for common code */
++ u16 memCap; /* cap bank1 in MB */
++
++ /* version 3 */
++ u8 wlan1_mac[6]; /* (ar5212) */
++};
++
++#define BOARD_CONFIG_BUFSZ 0x1000
++
++/*
++ * Platform device information for the Wireless MAC
++ */
++struct ar231x_board_config {
++ u16 devid;
++
++ /* board config data */
++ struct ar231x_boarddata *config;
++
++ /* radio calibration data */
++ const char *radio;
++};
++
++/*
++ * Platform device information for the Ethernet MAC
++ */
++struct ar231x_eth {
++ u32 reset_base;
++ u32 reset_mac;
++ u32 reset_phy;
++ u32 phy_base;
++ struct ar231x_board_config *config;
++ char *macaddr;
++};
++
++#endif /* __AR531X_PLATFORM_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/cpu-feature-overrides.h
+@@ -0,0 +1,84 @@
++/*
++ * Atheros SoC specific CPU feature overrides
++ *
++ * Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
++ *
++ * This file was derived from: include/asm-mips/cpu-features.h
++ * Copyright (C) 2003, 2004 Ralf Baechle
++ * Copyright (C) 2004 Maciej W. Rozycki
++ *
++ * This program is free software; you can redistribute it and/or modify it
++ * under the terms of the GNU General Public License version 2 as published
++ * by the Free Software Foundation.
++ *
++ */
++#ifndef __ASM_MACH_ATHEROS_CPU_FEATURE_OVERRIDES_H
++#define __ASM_MACH_ATHEROS_CPU_FEATURE_OVERRIDES_H
++
++/*
++ * The ATHEROS SoCs have MIPS 4Kc/4KEc core.
++ */
++#define cpu_has_tlb 1
++#define cpu_has_4kex 1
++#define cpu_has_3k_cache 0
++#define cpu_has_4k_cache 1
++#define cpu_has_tx39_cache 0
++#define cpu_has_sb1_cache 0
++#define cpu_has_fpu 0
++#define cpu_has_32fpr 0
++#define cpu_has_counter 1
++/* #define cpu_has_watch ? */
++/* #define cpu_has_divec ? */
++/* #define cpu_has_vce ? */
++/* #define cpu_has_cache_cdex_p ? */
++/* #define cpu_has_cache_cdex_s ? */
++/* #define cpu_has_prefetch ? */
++/* #define cpu_has_mcheck ? */
++#define cpu_has_ejtag 1
++
++#if !defined(CONFIG_ATHEROS_AR5312)
++# define cpu_has_llsc 1
++#else
++/*
++ * The MIPS 4Kc V0.9 core in the AR5312/AR2312 have problems with the
++ * ll/sc instructions.
++ */
++# define cpu_has_llsc 0
++#endif
++
++#define cpu_has_mips16 0
++#define cpu_has_mdmx 0
++#define cpu_has_mips3d 0
++#define cpu_has_smartmips 0
++
++/* #define cpu_has_vtag_icache ? */
++/* #define cpu_has_dc_aliases ? */
++/* #define cpu_has_ic_fills_f_dc ? */
++/* #define cpu_has_pindexed_dcache ? */
++
++/* #define cpu_icache_snoops_remote_store ? */
++
++#define cpu_has_mips32r1 1
++
++#if !defined(CONFIG_ATHEROS_AR5312)
++# define cpu_has_mips32r2 1
++#endif
++
++#define cpu_has_mips64r1 0
++#define cpu_has_mips64r2 0
++
++#define cpu_has_dsp 0
++#define cpu_has_mipsmt 0
++
++/* #define cpu_has_nofpuex ? */
++#define cpu_has_64bits 0
++#define cpu_has_64bit_zero_reg 0
++#define cpu_has_64bit_gp_regs 0
++#define cpu_has_64bit_addresses 0
++
++/* #define cpu_has_inclusive_pcaches ? */
++
++/* #define cpu_dcache_line_size() ? */
++/* #define cpu_icache_line_size() ? */
++
++#endif /* __ASM_MACH_ATHEROS_CPU_FEATURE_OVERRIDES_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/dma-coherence.h
+@@ -0,0 +1,41 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2006 Ralf Baechle <ralf@linux-mips.org>
++ * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
++ *
++ */
++#ifndef __ASM_MACH_GENERIC_DMA_COHERENCE_H
++#define __ASM_MACH_GENERIC_DMA_COHERENCE_H
++
++#define PCI_DMA_OFFSET 0x20000000
++
++struct device;
++
++static dma_addr_t plat_map_dma_mem(struct device *dev, void *addr, size_t size)
++{
++ return virt_to_phys(addr) + (dev != NULL ? PCI_DMA_OFFSET : 0);
++}
++
++static dma_addr_t plat_map_dma_mem_page(struct device *dev, struct page *page)
++{
++ return page_to_phys(page) + (dev != NULL ? PCI_DMA_OFFSET : 0);
++}
++
++static unsigned long plat_dma_addr_to_phys(dma_addr_t dma_addr)
++{
++ return (dma_addr > PCI_DMA_OFFSET ? dma_addr - PCI_DMA_OFFSET : dma_addr);
++}
++
++static void plat_unmap_dma_mem(dma_addr_t dma_addr)
++{
++}
++
++static inline int plat_device_is_coherent(struct device *dev)
++{
++ return 0;
++}
++
++#endif /* __ASM_MACH_GENERIC_DMA_COHERENCE_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/gpio.h
+@@ -0,0 +1,79 @@
++#ifndef _ATHEROS_GPIO_H_
++#define _ATHEROS_GPIO_H_
++
++#include <ar231x.h>
++
++struct ar231x_gpiodev {
++ u32 valid_mask;
++ u32 (*get_output)(void);
++ u32 (*set_output)(u32 mask, u32 val);
++ u32 (*get)(void);
++ u32 (*set)(u32 mask, u32 val);
++};
++
++extern const struct ar231x_gpiodev *ar231x_gpiodev;
++
++/*
++ * Wrappers for the generic GPIO layer
++ */
++
++static inline int gpio_direction_input(unsigned gpio) {
++ u32 mask = 1 << gpio;
++
++ if (!(ar231x_gpiodev->valid_mask & mask))
++ return -ENXIO;
++
++ ar231x_gpiodev->set_output(mask, 0);
++ return 0;
++}
++
++static inline void gpio_set_value(unsigned gpio, int value) {
++ u32 mask = 1 << gpio;
++
++ if (!(ar231x_gpiodev->valid_mask & mask))
++ return;
++
++ ar231x_gpiodev->set(mask, (!!value) * mask);
++}
++
++static inline int gpio_direction_output(unsigned gpio, int value) {
++ u32 mask = 1 << gpio;
++
++ if (!(ar231x_gpiodev->valid_mask & mask))
++ return -ENXIO;
++
++ ar231x_gpiodev->set_output(mask, mask);
++ ar231x_gpiodev->set(mask, (!!value) * mask);
++ return 0;
++}
++
++/* Reads the gpio pin. Unchecked function */
++static inline int gpio_get_value(unsigned gpio) {
++ u32 mask = 1 << gpio;
++
++ if (!(ar231x_gpiodev->valid_mask & mask))
++ return 0;
++
++ return !!(ar231x_gpiodev->get() & mask);
++}
++
++static inline int gpio_request(unsigned gpio, const char *label) {
++ return 0;
++}
++
++static inline void gpio_free(unsigned gpio) {
++}
++
++/* Returns IRQ to attach for gpio. Unchecked function */
++static inline int gpio_to_irq(unsigned gpio) {
++ return AR531X_GPIO_IRQ(gpio);
++}
++
++/* Returns gpio for IRQ attached. Unchecked function */
++static inline int irq_to_gpio(unsigned irq) {
++ return (irq - (AR531X_GPIO_IRQ(0)));
++}
++
++#include <asm-generic/gpio.h> /* cansleep wrappers */
++
++#endif
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/reset.h
+@@ -0,0 +1,6 @@
++#ifndef __AR531X_RESET_H
++#define __AR531X_RESET_H
++
++void ar531x_disable_reset_button(void);
++
++#endif /* __AR531X_RESET_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/war.h
+@@ -0,0 +1,25 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2008 Felix Fietkau <nbd@openwrt.org>
++ */
++#ifndef __ASM_MIPS_MACH_ATHEROS_WAR_H
++#define __ASM_MIPS_MACH_ATHEROS_WAR_H
++
++#define R4600_V1_INDEX_ICACHEOP_WAR 0
++#define R4600_V1_HIT_CACHEOP_WAR 0
++#define R4600_V2_HIT_CACHEOP_WAR 0
++#define R5432_CP0_INTERRUPT_WAR 0
++#define BCM1250_M3_WAR 0
++#define SIBYTE_1956_WAR 0
++#define MIPS4K_ICACHE_REFILL_WAR 0
++#define MIPS_CACHE_SYNC_WAR 0
++#define TX49XX_ICACHE_INDEX_INV_WAR 0
++#define RM9000_CDEX_SMP_WAR 0
++#define ICACHE_REFILLS_WORKAROUND_WAR 0
++#define R10000_LLSC_WAR 0
++#define MIPS34K_MISSED_ITLB_WAR 0
++
++#endif /* __ASM_MIPS_MACH_ATHEROS_WAR_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/ar2315_regs.h
+@@ -0,0 +1,580 @@
++/*
++ * Register definitions for AR2315+
++ *
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2008 Felix Fietkau <nbd@openwrt.org>
++ */
++
++#ifndef __AR2315_REG_H
++#define __AR2315_REG_H
++
++/*
++ * IRQs
++ */
++#define AR2315_IRQ_MISC_INTRS MIPS_CPU_IRQ_BASE+2 /* C0_CAUSE: 0x0400 */
++#define AR2315_IRQ_WLAN0_INTRS MIPS_CPU_IRQ_BASE+3 /* C0_CAUSE: 0x0800 */
++#define AR2315_IRQ_ENET0_INTRS MIPS_CPU_IRQ_BASE+4 /* C0_CAUSE: 0x1000 */
++#define AR2315_IRQ_LCBUS_PCI MIPS_CPU_IRQ_BASE+5 /* C0_CAUSE: 0x2000 */
++#define AR2315_IRQ_WLAN0_POLL MIPS_CPU_IRQ_BASE+6 /* C0_CAUSE: 0x4000 */
++
++/*
++ * Address map
++ */
++#define AR2315_SPI_READ 0x08000000 /* SPI FLASH */
++#define AR2315_WLAN0 0xB0000000 /* Wireless MMR */
++#define AR2315_PCI 0xB0100000 /* PCI MMR */
++#define AR2315_SDRAMCTL 0xB0300000 /* SDRAM MMR */
++#define AR2315_LOCAL 0xB0400000 /* LOCAL BUS MMR */
++#define AR2315_ENET0 0xB0500000 /* ETHERNET MMR */
++#define AR2315_DSLBASE 0xB1000000 /* RESET CONTROL MMR */
++#define AR2315_UART0 0xB1100003 /* UART MMR */
++#define AR2315_SPI 0xB1300000 /* SPI FLASH MMR */
++#define AR2315_PCIEXT 0x80000000 /* pci external */
++
++/*
++ * Reset Register
++ */
++#define AR2315_COLD_RESET (AR2315_DSLBASE + 0x0000)
++
++#define AR2315_RESET_COLD_AHB 0x00000001
++#define AR2315_RESET_COLD_APB 0x00000002
++#define AR2315_RESET_COLD_CPU 0x00000004
++#define AR2315_RESET_COLD_CPUWARM 0x00000008
++#define AR2315_RESET_SYSTEM (RESET_COLD_CPU | RESET_COLD_APB | RESET_COLD_AHB) /* full system */
++#define AR2317_RESET_SYSTEM 0x00000010
++
++
++#define AR2315_RESET (AR2315_DSLBASE + 0x0004)
++
++#define AR2315_RESET_WARM_WLAN0_MAC 0x00000001 /* warm reset WLAN0 MAC */
++#define AR2315_RESET_WARM_WLAN0_BB 0x00000002 /* warm reset WLAN0 BaseBand */
++#define AR2315_RESET_MPEGTS_RSVD 0x00000004 /* warm reset MPEG-TS */
++#define AR2315_RESET_PCIDMA 0x00000008 /* warm reset PCI ahb/dma */
++#define AR2315_RESET_MEMCTL 0x00000010 /* warm reset memory controller */
++#define AR2315_RESET_LOCAL 0x00000020 /* warm reset local bus */
++#define AR2315_RESET_I2C_RSVD 0x00000040 /* warm reset I2C bus */
++#define AR2315_RESET_SPI 0x00000080 /* warm reset SPI interface */
++#define AR2315_RESET_UART0 0x00000100 /* warm reset UART0 */
++#define AR2315_RESET_IR_RSVD 0x00000200 /* warm reset IR interface */
++#define AR2315_RESET_EPHY0 0x00000400 /* cold reset ENET0 phy */
++#define AR2315_RESET_ENET0 0x00000800 /* cold reset ENET0 mac */
++
++/*
++ * AHB master arbitration control
++ */
++#define AR2315_AHB_ARB_CTL (AR2315_DSLBASE + 0x0008)
++
++#define AR2315_ARB_CPU 0x00000001 /* CPU, default */
++#define AR2315_ARB_WLAN 0x00000002 /* WLAN */
++#define AR2315_ARB_MPEGTS_RSVD 0x00000004 /* MPEG-TS */
++#define AR2315_ARB_LOCAL 0x00000008 /* LOCAL */
++#define AR2315_ARB_PCI 0x00000010 /* PCI */
++#define AR2315_ARB_ETHERNET 0x00000020 /* Ethernet */
++#define AR2315_ARB_RETRY 0x00000100 /* retry policy, debug only */
++
++/*
++ * Config Register
++ */
++#define AR2315_ENDIAN_CTL (AR2315_DSLBASE + 0x000c)
++
++#define AR2315_CONFIG_AHB 0x00000001 /* EC - AHB bridge endianess */
++#define AR2315_CONFIG_WLAN 0x00000002 /* WLAN byteswap */
++#define AR2315_CONFIG_MPEGTS_RSVD 0x00000004 /* MPEG-TS byteswap */
++#define AR2315_CONFIG_PCI 0x00000008 /* PCI byteswap */
++#define AR2315_CONFIG_MEMCTL 0x00000010 /* Memory controller endianess */
++#define AR2315_CONFIG_LOCAL 0x00000020 /* Local bus byteswap */
++#define AR2315_CONFIG_ETHERNET 0x00000040 /* Ethernet byteswap */
++
++#define AR2315_CONFIG_MERGE 0x00000200 /* CPU write buffer merge */
++#define AR2315_CONFIG_CPU 0x00000400 /* CPU big endian */
++#define AR2315_CONFIG_PCIAHB 0x00000800
++#define AR2315_CONFIG_PCIAHB_BRIDGE 0x00001000
++#define AR2315_CONFIG_SPI 0x00008000 /* SPI byteswap */
++#define AR2315_CONFIG_CPU_DRAM 0x00010000
++#define AR2315_CONFIG_CPU_PCI 0x00020000
++#define AR2315_CONFIG_CPU_MMR 0x00040000
++#define AR2315_CONFIG_BIG 0x00000400
++
++
++/*
++ * NMI control
++ */
++#define AR2315_NMI_CTL (AR2315_DSLBASE + 0x0010)
++
++#define AR2315_NMI_EN 1
++
++/*
++ * Revision Register - Initial value is 0x3010 (WMAC 3.0, AR531X 1.0).
++ */
++#define AR2315_SREV (AR2315_DSLBASE + 0x0014)
++
++#define AR2315_REV_MAJ 0x00f0
++#define AR2315_REV_MAJ_S 4
++#define AR2315_REV_MIN 0x000f
++#define AR2315_REV_MIN_S 0
++#define AR2315_REV_CHIP (AR2315_REV_MAJ|AR2315_REV_MIN)
++
++/*
++ * Interface Enable
++ */
++#define AR2315_IF_CTL (AR2315_DSLBASE + 0x0018)
++
++#define AR2315_IF_MASK 0x00000007
++#define AR2315_IF_DISABLED 0
++#define AR2315_IF_PCI 1
++#define AR2315_IF_TS_LOCAL 2
++#define AR2315_IF_ALL 3 /* only for emulation with separate pins */
++#define AR2315_IF_LOCAL_HOST 0x00000008
++#define AR2315_IF_PCI_HOST 0x00000010
++#define AR2315_IF_PCI_INTR 0x00000020
++#define AR2315_IF_PCI_CLK_MASK 0x00030000
++#define AR2315_IF_PCI_CLK_INPUT 0
++#define AR2315_IF_PCI_CLK_OUTPUT_LOW 1
++#define AR2315_IF_PCI_CLK_OUTPUT_CLK 2
++#define AR2315_IF_PCI_CLK_OUTPUT_HIGH 3
++#define AR2315_IF_PCI_CLK_SHIFT 16
++
++/*
++ * APB Interrupt control
++ */
++
++#define AR2315_ISR (AR2315_DSLBASE + 0x0020)
++#define AR2315_IMR (AR2315_DSLBASE + 0x0024)
++#define AR2315_GISR (AR2315_DSLBASE + 0x0028)
++
++#define AR2315_ISR_UART0 0x0001 /* high speed UART */
++#define AR2315_ISR_I2C_RSVD 0x0002 /* I2C bus */
++#define AR2315_ISR_SPI 0x0004 /* SPI bus */
++#define AR2315_ISR_AHB 0x0008 /* AHB error */
++#define AR2315_ISR_APB 0x0010 /* APB error */
++#define AR2315_ISR_TIMER 0x0020 /* timer */
++#define AR2315_ISR_GPIO 0x0040 /* GPIO */
++#define AR2315_ISR_WD 0x0080 /* watchdog */
++#define AR2315_ISR_IR_RSVD 0x0100 /* IR */
++
++#define AR2315_GISR_MISC 0x0001
++#define AR2315_GISR_WLAN0 0x0002
++#define AR2315_GISR_MPEGTS_RSVD 0x0004
++#define AR2315_GISR_LOCALPCI 0x0008
++#define AR2315_GISR_WMACPOLL 0x0010
++#define AR2315_GISR_TIMER 0x0020
++#define AR2315_GISR_ETHERNET 0x0040
++
++/*
++ * Interrupt routing from IO to the processor IP bits
++ * Define our inter mask and level
++ */
++#define AR2315_INTR_MISCIO SR_IBIT3
++#define AR2315_INTR_WLAN0 SR_IBIT4
++#define AR2315_INTR_ENET0 SR_IBIT5
++#define AR2315_INTR_LOCALPCI SR_IBIT6
++#define AR2315_INTR_WMACPOLL SR_IBIT7
++#define AR2315_INTR_COMPARE SR_IBIT8
++
++/*
++ * Timers
++ */
++#define AR2315_TIMER (AR2315_DSLBASE + 0x0030)
++#define AR2315_RELOAD (AR2315_DSLBASE + 0x0034)
++#define AR2315_WD (AR2315_DSLBASE + 0x0038)
++#define AR2315_WDC (AR2315_DSLBASE + 0x003c)
++
++#define AR2315_WDC_IGNORE_EXPIRATION 0x00000000
++#define AR2315_WDC_NMI 0x00000001 /* NMI on watchdog */
++#define AR2315_WDC_RESET 0x00000002 /* reset on watchdog */
++
++/*
++ * CPU Performance Counters
++ */
++#define AR2315_PERFCNT0 (AR2315_DSLBASE + 0x0048)
++#define AR2315_PERFCNT1 (AR2315_DSLBASE + 0x004c)
++
++#define AR2315_PERF0_DATAHIT 0x0001 /* Count Data Cache Hits */
++#define AR2315_PERF0_DATAMISS 0x0002 /* Count Data Cache Misses */
++#define AR2315_PERF0_INSTHIT 0x0004 /* Count Instruction Cache Hits */
++#define AR2315_PERF0_INSTMISS 0x0008 /* Count Instruction Cache Misses */
++#define AR2315_PERF0_ACTIVE 0x0010 /* Count Active Processor Cycles */
++#define AR2315_PERF0_WBHIT 0x0020 /* Count CPU Write Buffer Hits */
++#define AR2315_PERF0_WBMISS 0x0040 /* Count CPU Write Buffer Misses */
++
++#define AR2315_PERF1_EB_ARDY 0x0001 /* Count EB_ARdy signal */
++#define AR2315_PERF1_EB_AVALID 0x0002 /* Count EB_AValid signal */
++#define AR2315_PERF1_EB_WDRDY 0x0004 /* Count EB_WDRdy signal */
++#define AR2315_PERF1_EB_RDVAL 0x0008 /* Count EB_RdVal signal */
++#define AR2315_PERF1_VRADDR 0x0010 /* Count valid read address cycles */
++#define AR2315_PERF1_VWADDR 0x0020 /* Count valid write address cycles */
++#define AR2315_PERF1_VWDATA 0x0040 /* Count valid write data cycles */
++
++/*
++ * AHB Error Reporting.
++ */
++#define AR2315_AHB_ERR0 (AR2315_DSLBASE + 0x0050) /* error */
++#define AR2315_AHB_ERR1 (AR2315_DSLBASE + 0x0054) /* haddr */
++#define AR2315_AHB_ERR2 (AR2315_DSLBASE + 0x0058) /* hwdata */
++#define AR2315_AHB_ERR3 (AR2315_DSLBASE + 0x005c) /* hrdata */
++#define AR2315_AHB_ERR4 (AR2315_DSLBASE + 0x0060) /* status */
++
++#define AHB_ERROR_DET 1 /* AHB Error has been detected, */
++ /* write 1 to clear all bits in ERR0 */
++#define AHB_ERROR_OVR 2 /* AHB Error overflow has been detected */
++#define AHB_ERROR_WDT 4 /* AHB Error due to wdt instead of hresp */
++
++#define AR2315_PROCERR_HMAST 0x0000000f
++#define AR2315_PROCERR_HMAST_DFLT 0
++#define AR2315_PROCERR_HMAST_WMAC 1
++#define AR2315_PROCERR_HMAST_ENET 2
++#define AR2315_PROCERR_HMAST_PCIENDPT 3
++#define AR2315_PROCERR_HMAST_LOCAL 4
++#define AR2315_PROCERR_HMAST_CPU 5
++#define AR2315_PROCERR_HMAST_PCITGT 6
++
++#define AR2315_PROCERR_HMAST_S 0
++#define AR2315_PROCERR_HWRITE 0x00000010
++#define AR2315_PROCERR_HSIZE 0x00000060
++#define AR2315_PROCERR_HSIZE_S 5
++#define AR2315_PROCERR_HTRANS 0x00000180
++#define AR2315_PROCERR_HTRANS_S 7
++#define AR2315_PROCERR_HBURST 0x00000e00
++#define AR2315_PROCERR_HBURST_S 9
++
++/*
++ * Clock Control
++ */
++#define AR2315_PLLC_CTL (AR2315_DSLBASE + 0x0064)
++#define AR2315_PLLV_CTL (AR2315_DSLBASE + 0x0068)
++#define AR2315_CPUCLK (AR2315_DSLBASE + 0x006c)
++#define AR2315_AMBACLK (AR2315_DSLBASE + 0x0070)
++#define AR2315_SYNCCLK (AR2315_DSLBASE + 0x0074)
++#define AR2315_DSL_SLEEP_CTL (AR2315_DSLBASE + 0x0080)
++#define AR2315_DSL_SLEEP_DUR (AR2315_DSLBASE + 0x0084)
++
++/* PLLc Control fields */
++#define PLLC_REF_DIV_M 0x00000003
++#define PLLC_REF_DIV_S 0
++#define PLLC_FDBACK_DIV_M 0x0000007C
++#define PLLC_FDBACK_DIV_S 2
++#define PLLC_ADD_FDBACK_DIV_M 0x00000080
++#define PLLC_ADD_FDBACK_DIV_S 7
++#define PLLC_CLKC_DIV_M 0x0001c000
++#define PLLC_CLKC_DIV_S 14
++#define PLLC_CLKM_DIV_M 0x00700000
++#define PLLC_CLKM_DIV_S 20
++
++/* CPU CLK Control fields */
++#define CPUCLK_CLK_SEL_M 0x00000003
++#define CPUCLK_CLK_SEL_S 0
++#define CPUCLK_CLK_DIV_M 0x0000000c
++#define CPUCLK_CLK_DIV_S 2
++
++/* AMBA CLK Control fields */
++#define AMBACLK_CLK_SEL_M 0x00000003
++#define AMBACLK_CLK_SEL_S 0
++#define AMBACLK_CLK_DIV_M 0x0000000c
++#define AMBACLK_CLK_DIV_S 2
++
++/*
++ * GPIO
++ */
++#define AR2315_GPIO_DI (AR2315_DSLBASE + 0x0088)
++#define AR2315_GPIO_DO (AR2315_DSLBASE + 0x0090)
++#define AR2315_GPIO_CR (AR2315_DSLBASE + 0x0098)
++#define AR2315_GPIO_INT (AR2315_DSLBASE + 0x00a0)
++
++#define AR2315_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
++#define AR2315_GPIO_CR_O(x) (1 << (x)) /* output */
++#define AR2315_GPIO_CR_I(x) (0) /* input */
++
++#define AR2315_GPIO_INT_S(x) (x) /* interrupt enable */
++#define AR2315_GPIO_INT_M (0x3F) /* mask for int */
++#define AR2315_GPIO_INT_LVL(x) ((x) << 6) /* interrupt level */
++#define AR2315_GPIO_INT_LVL_M ((0x3) << 6) /* mask for int level */
++
++#define AR2315_GPIO_INT_MAX_Y 1 /* Maximum value of Y for AR5313_GPIO_INT_* macros */
++#define AR2315_GPIO_INT_LVL_OFF 0 /* Triggerring off */
++#define AR2315_GPIO_INT_LVL_LOW 1 /* Low Level Triggered */
++#define AR2315_GPIO_INT_LVL_HIGH 2 /* High Level Triggered */
++#define AR2315_GPIO_INT_LVL_EDGE 3 /* Edge Triggered */
++
++#define AR2315_RESET_GPIO 5
++#define AR2315_NUM_GPIO 22
++
++/*
++ * PCI Clock Control
++ */
++#define AR2315_PCICLK (AR2315_DSLBASE + 0x00a4)
++
++#define AR2315_PCICLK_INPUT_M 0x3
++#define AR2315_PCICLK_INPUT_S 0
++
++#define AR2315_PCICLK_PLLC_CLKM 0
++#define AR2315_PCICLK_PLLC_CLKM1 1
++#define AR2315_PCICLK_PLLC_CLKC 2
++#define AR2315_PCICLK_REF_CLK 3
++
++#define AR2315_PCICLK_DIV_M 0xc
++#define AR2315_PCICLK_DIV_S 2
++
++#define AR2315_PCICLK_IN_FREQ 0
++#define AR2315_PCICLK_IN_FREQ_DIV_6 1
++#define AR2315_PCICLK_IN_FREQ_DIV_8 2
++#define AR2315_PCICLK_IN_FREQ_DIV_10 3
++
++/*
++ * Observation Control Register
++ */
++#define AR2315_OCR (AR2315_DSLBASE + 0x00b0)
++#define OCR_GPIO0_IRIN 0x0040
++#define OCR_GPIO1_IROUT 0x0080
++#define OCR_GPIO3_RXCLR 0x0200
++
++/*
++ * General Clock Control
++ */
++
++#define AR2315_MISCCLK (AR2315_DSLBASE + 0x00b4)
++#define MISCCLK_PLLBYPASS_EN 0x00000001
++#define MISCCLK_PROCREFCLK 0x00000002
++
++/*
++ * SDRAM Controller
++ * - No read or write buffers are included.
++ */
++#define AR2315_MEM_CFG (AR2315_SDRAMCTL + 0x00)
++#define AR2315_MEM_CTRL (AR2315_SDRAMCTL + 0x0c)
++#define AR2315_MEM_REF (AR2315_SDRAMCTL + 0x10)
++
++#define SDRAM_DATA_WIDTH_M 0x00006000
++#define SDRAM_DATA_WIDTH_S 13
++
++#define SDRAM_COL_WIDTH_M 0x00001E00
++#define SDRAM_COL_WIDTH_S 9
++
++#define SDRAM_ROW_WIDTH_M 0x000001E0
++#define SDRAM_ROW_WIDTH_S 5
++
++#define SDRAM_BANKADDR_BITS_M 0x00000018
++#define SDRAM_BANKADDR_BITS_S 3
++
++/*
++ * SPI Flash Interface Registers
++ */
++
++#define AR2315_SPI_CTL (AR2315_SPI + 0x00)
++#define AR2315_SPI_OPCODE (AR2315_SPI + 0x04)
++#define AR2315_SPI_DATA (AR2315_SPI + 0x08)
++
++#define SPI_CTL_START 0x00000100
++#define SPI_CTL_BUSY 0x00010000
++#define SPI_CTL_TXCNT_MASK 0x0000000f
++#define SPI_CTL_RXCNT_MASK 0x000000f0
++#define SPI_CTL_TX_RX_CNT_MASK 0x000000ff
++#define SPI_CTL_SIZE_MASK 0x00060000
++
++#define SPI_CTL_CLK_SEL_MASK 0x03000000
++#define SPI_OPCODE_MASK 0x000000ff
++
++/*
++ * PCI Bus Interface Registers
++ */
++#define AR2315_PCI_1MS_REG (AR2315_PCI + 0x0008)
++#define AR2315_PCI_1MS_MASK 0x3FFFF /* # of AHB clk cycles in 1ms */
++
++#define AR2315_PCI_MISC_CONFIG (AR2315_PCI + 0x000c)
++#define AR2315_PCIMISC_TXD_EN 0x00000001 /* Enable TXD for fragments */
++#define AR2315_PCIMISC_CFG_SEL 0x00000002 /* mem or config cycles */
++#define AR2315_PCIMISC_GIG_MASK 0x0000000C /* bits 31-30 for pci req */
++#define AR2315_PCIMISC_RST_MODE 0x00000030
++#define AR2315_PCIRST_INPUT 0x00000000 /* 4:5=0 rst is input */
++#define AR2315_PCIRST_LOW 0x00000010 /* 4:5=1 rst to GND */
++#define AR2315_PCIRST_HIGH 0x00000020 /* 4:5=2 rst to VDD */
++#define AR2315_PCIGRANT_EN 0x00000000 /* 6:7=0 early grant en */
++#define AR2315_PCIGRANT_FRAME 0x00000040 /* 6:7=1 grant waits 4 frame */
++#define AR2315_PCIGRANT_IDLE 0x00000080 /* 6:7=2 grant waits 4 idle */
++#define AR2315_PCIGRANT_GAP 0x00000000 /* 6:7=2 grant waits 4 idle */
++#define AR2315_PCICACHE_DIS 0x00001000 /* PCI external access cache disable */
++
++#define AR2315_PCI_OUT_TSTAMP (AR2315_PCI + 0x0010)
++
++#define AR2315_PCI_UNCACHE_CFG (AR2315_PCI + 0x0014)
++
++#define AR2315_PCI_IN_EN (AR2315_PCI + 0x0100)
++#define AR2315_PCI_IN_EN0 0x01 /* Enable chain 0 */
++#define AR2315_PCI_IN_EN1 0x02 /* Enable chain 1 */
++#define AR2315_PCI_IN_EN2 0x04 /* Enable chain 2 */
++#define AR2315_PCI_IN_EN3 0x08 /* Enable chain 3 */
++
++#define AR2315_PCI_IN_DIS (AR2315_PCI + 0x0104)
++#define AR2315_PCI_IN_DIS0 0x01 /* Disable chain 0 */
++#define AR2315_PCI_IN_DIS1 0x02 /* Disable chain 1 */
++#define AR2315_PCI_IN_DIS2 0x04 /* Disable chain 2 */
++#define AR2315_PCI_IN_DIS3 0x08 /* Disable chain 3 */
++
++#define AR2315_PCI_IN_PTR (AR2315_PCI + 0x0200)
++
++#define AR2315_PCI_OUT_EN (AR2315_PCI + 0x0400)
++#define AR2315_PCI_OUT_EN0 0x01 /* Enable chain 0 */
++
++#define AR2315_PCI_OUT_DIS (AR2315_PCI + 0x0404)
++#define AR2315_PCI_OUT_DIS0 0x01 /* Disable chain 0 */
++
++#define AR2315_PCI_OUT_PTR (AR2315_PCI + 0x0408)
++
++#define AR2315_PCI_INT_STATUS (AR2315_PCI + 0x0500) /* write one to clr */
++#define AR2315_PCI_TXINT 0x00000001 /* Desc In Completed */
++#define AR2315_PCI_TXOK 0x00000002 /* Desc In OK */
++#define AR2315_PCI_TXERR 0x00000004 /* Desc In ERR */
++#define AR2315_PCI_TXEOL 0x00000008 /* Desc In End-of-List */
++#define AR2315_PCI_RXINT 0x00000010 /* Desc Out Completed */
++#define AR2315_PCI_RXOK 0x00000020 /* Desc Out OK */
++#define AR2315_PCI_RXERR 0x00000040 /* Desc Out ERR */
++#define AR2315_PCI_RXEOL 0x00000080 /* Desc Out EOL */
++#define AR2315_PCI_TXOOD 0x00000200 /* Desc In Out-of-Desc */
++#define AR2315_PCI_MASK 0x0000FFFF /* Desc Mask */
++#define AR2315_PCI_EXT_INT 0x02000000
++#define AR2315_PCI_ABORT_INT 0x04000000
++
++#define AR2315_PCI_INT_MASK (AR2315_PCI + 0x0504) /* same as INT_STATUS */
++
++#define AR2315_PCI_INTEN_REG (AR2315_PCI + 0x0508)
++#define AR2315_PCI_INT_DISABLE 0x00 /* disable pci interrupts */
++#define AR2315_PCI_INT_ENABLE 0x01 /* enable pci interrupts */
++
++#define AR2315_PCI_HOST_IN_EN (AR2315_PCI + 0x0800)
++#define AR2315_PCI_HOST_IN_DIS (AR2315_PCI + 0x0804)
++#define AR2315_PCI_HOST_IN_PTR (AR2315_PCI + 0x0810)
++#define AR2315_PCI_HOST_OUT_EN (AR2315_PCI + 0x0900)
++#define AR2315_PCI_HOST_OUT_DIS (AR2315_PCI + 0x0904)
++#define AR2315_PCI_HOST_OUT_PTR (AR2315_PCI + 0x0908)
++
++
++/*
++ * Local Bus Interface Registers
++ */
++#define AR2315_LB_CONFIG (AR2315_LOCAL + 0x0000)
++#define AR2315_LBCONF_OE 0x00000001 /* =1 OE is low-true */
++#define AR2315_LBCONF_CS0 0x00000002 /* =1 first CS is low-true */
++#define AR2315_LBCONF_CS1 0x00000004 /* =1 2nd CS is low-true */
++#define AR2315_LBCONF_RDY 0x00000008 /* =1 RDY is low-true */
++#define AR2315_LBCONF_WE 0x00000010 /* =1 Write En is low-true */
++#define AR2315_LBCONF_WAIT 0x00000020 /* =1 WAIT is low-true */
++#define AR2315_LBCONF_ADS 0x00000040 /* =1 Adr Strobe is low-true */
++#define AR2315_LBCONF_MOT 0x00000080 /* =0 Intel, =1 Motorola */
++#define AR2315_LBCONF_8CS 0x00000100 /* =1 8 bits CS, 0= 16bits */
++#define AR2315_LBCONF_8DS 0x00000200 /* =1 8 bits Data S, 0=16bits */
++#define AR2315_LBCONF_ADS_EN 0x00000400 /* =1 Enable ADS */
++#define AR2315_LBCONF_ADR_OE 0x00000800 /* =1 Adr cap on OE, WE or DS */
++#define AR2315_LBCONF_ADDT_MUX 0x00001000 /* =1 Adr and Data share bus */
++#define AR2315_LBCONF_DATA_OE 0x00002000 /* =1 Data cap on OE, WE, DS */
++#define AR2315_LBCONF_16DATA 0x00004000 /* =1 Data is 16 bits wide */
++#define AR2315_LBCONF_SWAPDT 0x00008000 /* =1 Byte swap data */
++#define AR2315_LBCONF_SYNC 0x00010000 /* =1 Bus synchronous to clk */
++#define AR2315_LBCONF_INT 0x00020000 /* =1 Intr is low true */
++#define AR2315_LBCONF_INT_CTR0 0x00000000 /* GND high-Z, Vdd is high-Z */
++#define AR2315_LBCONF_INT_CTR1 0x00040000 /* GND drive, Vdd is high-Z */
++#define AR2315_LBCONF_INT_CTR2 0x00080000 /* GND high-Z, Vdd drive */
++#define AR2315_LBCONF_INT_CTR3 0x000C0000 /* GND drive, Vdd drive */
++#define AR2315_LBCONF_RDY_WAIT 0x00100000 /* =1 RDY is negative of WAIT */
++#define AR2315_LBCONF_INT_PULSE 0x00200000 /* =1 Interrupt is a pulse */
++#define AR2315_LBCONF_ENABLE 0x00400000 /* =1 Falcon respond to LB */
++
++#define AR2315_LB_CLKSEL (AR2315_LOCAL + 0x0004)
++#define AR2315_LBCLK_EXT 0x0001 /* use external clk for lb */
++
++#define AR2315_LB_1MS (AR2315_LOCAL + 0x0008)
++#define AR2315_LB1MS_MASK 0x3FFFF /* # of AHB clk cycles in 1ms */
++
++#define AR2315_LB_MISCCFG (AR2315_LOCAL + 0x000C)
++#define AR2315_LBM_TXD_EN 0x00000001 /* Enable TXD for fragments */
++#define AR2315_LBM_RX_INTEN 0x00000002 /* Enable LB ints on RX ready */
++#define AR2315_LBM_MBOXWR_INTEN 0x00000004 /* Enable LB ints on mbox wr */
++#define AR2315_LBM_MBOXRD_INTEN 0x00000008 /* Enable LB ints on mbox rd */
++#define AR2315_LMB_DESCSWAP_EN 0x00000010 /* Byte swap desc enable */
++#define AR2315_LBM_TIMEOUT_MASK 0x00FFFF80
++#define AR2315_LBM_TIMEOUT_SHFT 7
++#define AR2315_LBM_PORTMUX 0x07000000
++
++
++#define AR2315_LB_RXTSOFF (AR2315_LOCAL + 0x0010)
++
++#define AR2315_LB_TX_CHAIN_EN (AR2315_LOCAL + 0x0100)
++#define AR2315_LB_TXEN_0 0x01
++#define AR2315_LB_TXEN_1 0x02
++#define AR2315_LB_TXEN_2 0x04
++#define AR2315_LB_TXEN_3 0x08
++
++#define AR2315_LB_TX_CHAIN_DIS (AR2315_LOCAL + 0x0104)
++#define AR2315_LB_TX_DESC_PTR (AR2315_LOCAL + 0x0200)
++
++#define AR2315_LB_RX_CHAIN_EN (AR2315_LOCAL + 0x0400)
++#define AR2315_LB_RXEN 0x01
++
++#define AR2315_LB_RX_CHAIN_DIS (AR2315_LOCAL + 0x0404)
++#define AR2315_LB_RX_DESC_PTR (AR2315_LOCAL + 0x0408)
++
++#define AR2315_LB_INT_STATUS (AR2315_LOCAL + 0x0500)
++#define AR2315_INT_TX_DESC 0x0001
++#define AR2315_INT_TX_OK 0x0002
++#define AR2315_INT_TX_ERR 0x0004
++#define AR2315_INT_TX_EOF 0x0008
++#define AR2315_INT_RX_DESC 0x0010
++#define AR2315_INT_RX_OK 0x0020
++#define AR2315_INT_RX_ERR 0x0040
++#define AR2315_INT_RX_EOF 0x0080
++#define AR2315_INT_TX_TRUNC 0x0100
++#define AR2315_INT_TX_STARVE 0x0200
++#define AR2315_INT_LB_TIMEOUT 0x0400
++#define AR2315_INT_LB_ERR 0x0800
++#define AR2315_INT_MBOX_WR 0x1000
++#define AR2315_INT_MBOX_RD 0x2000
++
++/* Bit definitions for INT MASK are the same as INT_STATUS */
++#define AR2315_LB_INT_MASK (AR2315_LOCAL + 0x0504)
++
++#define AR2315_LB_INT_EN (AR2315_LOCAL + 0x0508)
++#define AR2315_LB_MBOX (AR2315_LOCAL + 0x0600)
++
++/*
++ * IR Interface Registers
++ */
++#define AR2315_IR_PKTDATA (AR2315_IR + 0x0000)
++
++#define AR2315_IR_PKTLEN (AR2315_IR + 0x07fc) /* 0 - 63 */
++
++#define AR2315_IR_CONTROL (AR2315_IR + 0x0800)
++#define AR2315_IRCTL_TX 0x00000000 /* use as tranmitter */
++#define AR2315_IRCTL_RX 0x00000001 /* use as receiver */
++#define AR2315_IRCTL_SAMPLECLK_MASK 0x00003ffe /* Sample clk divisor mask */
++#define AR2315_IRCTL_SAMPLECLK_SHFT 1
++#define AR2315_IRCTL_OUTPUTCLK_MASK 0x03ffc000 /* Output clk divisor mask */
++#define AR2315_IRCTL_OUTPUTCLK_SHFT 14
++
++#define AR2315_IR_STATUS (AR2315_IR + 0x0804)
++#define AR2315_IRSTS_RX 0x00000001 /* receive in progress */
++#define AR2315_IRSTS_TX 0x00000002 /* transmit in progress */
++
++#define AR2315_IR_CONFIG (AR2315_IR + 0x0808)
++#define AR2315_IRCFG_INVIN 0x00000001 /* invert input polarity */
++#define AR2315_IRCFG_INVOUT 0x00000002 /* invert output polarity */
++#define AR2315_IRCFG_SEQ_START_WIN_SEL 0x00000004 /* 1 => 28, 0 => 7 */
++#define AR2315_IRCFG_SEQ_START_THRESH 0x000000f0 /* */
++#define AR2315_IRCFG_SEQ_END_UNIT_SEL 0x00000100 /* */
++#define AR2315_IRCFG_SEQ_END_UNIT_THRESH 0x00007e00 /* */
++#define AR2315_IRCFG_SEQ_END_WIN_SEL 0x00008000 /* */
++#define AR2315_IRCFG_SEQ_END_WIN_THRESH 0x001f0000 /* */
++#define AR2315_IRCFG_NUM_BACKOFF_WORDS 0x01e00000 /* */
++
++#define HOST_PCI_DEV_ID 3
++#define HOST_PCI_MBAR0 0x10000000
++#define HOST_PCI_MBAR1 0x20000000
++#define HOST_PCI_MBAR2 0x30000000
++
++#define HOST_PCI_SDRAM_BASEADDR HOST_PCI_MBAR1
++#define PCI_DEVICE_MEM_SPACE 0x800000
++
++#endif /* __AR2315_REG_H */
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/ar5312_regs.h
+@@ -0,0 +1,236 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
++ */
++
++#ifndef AR5312_H
++#define AR5312_H
++
++#include <asm/addrspace.h>
++
++/*
++ * IRQs
++ */
++
++#define AR5312_IRQ_WLAN0_INTRS MIPS_CPU_IRQ_BASE+2 /* C0_CAUSE: 0x0400 */
++#define AR5312_IRQ_ENET0_INTRS MIPS_CPU_IRQ_BASE+3 /* C0_CAUSE: 0x0800 */
++#define AR5312_IRQ_ENET1_INTRS MIPS_CPU_IRQ_BASE+4 /* C0_CAUSE: 0x1000 */
++#define AR5312_IRQ_WLAN1_INTRS MIPS_CPU_IRQ_BASE+5 /* C0_CAUSE: 0x2000 */
++#define AR5312_IRQ_MISC_INTRS MIPS_CPU_IRQ_BASE+6 /* C0_CAUSE: 0x4000 */
++
++
++/* Address Map */
++#define AR531X_WLAN0 0x18000000
++#define AR531X_WLAN1 0x18500000
++#define AR531X_ENET0 0x18100000
++#define AR531X_ENET1 0x18200000
++#define AR531X_SDRAMCTL 0x18300000
++#define AR531X_FLASHCTL 0x18400000
++#define AR531X_APBBASE 0x1c000000
++#define AR531X_FLASH 0x1e000000
++#define AR531X_UART0 0xbc000003 /* UART MMR */
++
++/*
++ * AR531X_NUM_ENET_MAC defines the number of ethernet MACs that
++ * should be considered available. The AR5312 supports 2 enet MACS,
++ * even though many reference boards only actually use 1 of them
++ * (i.e. Only MAC 0 is actually connected to an enet PHY or PHY switch.
++ * The AR2312 supports 1 enet MAC.
++ */
++#define AR531X_NUM_ENET_MAC 2
++
++/*
++ * Need these defines to determine true number of ethernet MACs
++ */
++#define AR5212_AR5312_REV2 0x0052 /* AR5312 WMAC (AP31) */
++#define AR5212_AR5312_REV7 0x0057 /* AR5312 WMAC (AP30-040) */
++#define AR5212_AR2313_REV8 0x0058 /* AR2313 WMAC (AP43-030) */
++#define AR531X_RADIO_MASK_OFF 0xc8
++#define AR531X_RADIO0_MASK 0x0003
++#define AR531X_RADIO1_MASK 0x000c
++#define AR531X_RADIO1_S 2
++
++/*
++ * AR531X_NUM_WMAC defines the number of Wireless MACs that\
++ * should be considered available.
++ */
++#define AR531X_NUM_WMAC 2
++
++/* Reset/Timer Block Address Map */
++#define AR531X_RESETTMR (AR531X_APBBASE + 0x3000)
++#define AR531X_TIMER (AR531X_RESETTMR + 0x0000) /* countdown timer */
++#define AR531X_WD_CTRL (AR531X_RESETTMR + 0x0008) /* watchdog cntrl */
++#define AR531X_WD_TIMER (AR531X_RESETTMR + 0x000c) /* watchdog timer */
++#define AR531X_ISR (AR531X_RESETTMR + 0x0010) /* Intr Status Reg */
++#define AR531X_IMR (AR531X_RESETTMR + 0x0014) /* Intr Mask Reg */
++#define AR531X_RESET (AR531X_RESETTMR + 0x0020)
++#define AR5312_CLOCKCTL1 (AR531X_RESETTMR + 0x0064)
++#define AR5312_SCRATCH (AR531X_RESETTMR + 0x006c)
++#define AR531X_PROCADDR (AR531X_RESETTMR + 0x0070)
++#define AR531X_PROC1 (AR531X_RESETTMR + 0x0074)
++#define AR531X_DMAADDR (AR531X_RESETTMR + 0x0078)
++#define AR531X_DMA1 (AR531X_RESETTMR + 0x007c)
++#define AR531X_ENABLE (AR531X_RESETTMR + 0x0080) /* interface enb */
++#define AR531X_REV (AR531X_RESETTMR + 0x0090) /* revision */
++
++/* AR531X_WD_CTRL register bit field definitions */
++#define AR531X_WD_CTRL_IGNORE_EXPIRATION 0x0000
++#define AR531X_WD_CTRL_NMI 0x0001
++#define AR531X_WD_CTRL_RESET 0x0002
++
++/* AR531X_ISR register bit field definitions */
++#define AR531X_ISR_NONE 0x0000
++#define AR531X_ISR_TIMER 0x0001
++#define AR531X_ISR_AHBPROC 0x0002
++#define AR531X_ISR_AHBDMA 0x0004
++#define AR531X_ISR_GPIO 0x0008
++#define AR531X_ISR_UART0 0x0010
++#define AR531X_ISR_UART0DMA 0x0020
++#define AR531X_ISR_WD 0x0040
++#define AR531X_ISR_LOCAL 0x0080
++
++/* AR531X_RESET register bit field definitions */
++#define AR531X_RESET_SYSTEM 0x00000001 /* cold reset full system */
++#define AR531X_RESET_PROC 0x00000002 /* cold reset MIPS core */
++#define AR531X_RESET_WLAN0 0x00000004 /* cold reset WLAN MAC and BB */
++#define AR531X_RESET_EPHY0 0x00000008 /* cold reset ENET0 phy */
++#define AR531X_RESET_EPHY1 0x00000010 /* cold reset ENET1 phy */
++#define AR531X_RESET_ENET0 0x00000020 /* cold reset ENET0 mac */
++#define AR531X_RESET_ENET1 0x00000040 /* cold reset ENET1 mac */
++#define AR531X_RESET_UART0 0x00000100 /* cold reset UART0 (high speed) */
++#define AR531X_RESET_WLAN1 0x00000200 /* cold reset WLAN MAC/BB */
++#define AR531X_RESET_APB 0x00000400 /* cold reset APB (ar5312) */
++#define AR531X_RESET_WARM_PROC 0x00001000 /* warm reset MIPS core */
++#define AR531X_RESET_WARM_WLAN0_MAC 0x00002000 /* warm reset WLAN0 MAC */
++#define AR531X_RESET_WARM_WLAN0_BB 0x00004000 /* warm reset WLAN0 BaseBand */
++#define AR531X_RESET_NMI 0x00010000 /* send an NMI to the processor */
++#define AR531X_RESET_WARM_WLAN1_MAC 0x00020000 /* warm reset WLAN1 mac */
++#define AR531X_RESET_WARM_WLAN1_BB 0x00040000 /* warm reset WLAN1 baseband */
++#define AR531X_RESET_LOCAL_BUS 0x00080000 /* reset local bus */
++#define AR531X_RESET_WDOG 0x00100000 /* last reset was a watchdog */
++
++#define AR531X_RESET_WMAC0_BITS \
++ AR531X_RESET_WLAN0 |\
++ AR531X_RESET_WARM_WLAN0_MAC |\
++ AR531X_RESET_WARM_WLAN0_BB
++
++#define AR531X_RESERT_WMAC1_BITS \
++ AR531X_RESET_WLAN1 |\
++ AR531X_RESET_WARM_WLAN1_MAC |\
++ AR531X_RESET_WARM_WLAN1_BB
++
++/* AR5312_CLOCKCTL1 register bit field definitions */
++#define AR5312_CLOCKCTL1_PREDIVIDE_MASK 0x00000030
++#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT 4
++#define AR5312_CLOCKCTL1_MULTIPLIER_MASK 0x00001f00
++#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT 8
++#define AR5312_CLOCKCTL1_DOUBLER_MASK 0x00010000
++
++/* Valid for AR5312 and AR2312 */
++#define AR5312_CLOCKCTL1_PREDIVIDE_MASK 0x00000030
++#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT 4
++#define AR5312_CLOCKCTL1_MULTIPLIER_MASK 0x00001f00
++#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT 8
++#define AR5312_CLOCKCTL1_DOUBLER_MASK 0x00010000
++
++/* Valid for AR2313 */
++#define AR2313_CLOCKCTL1_PREDIVIDE_MASK 0x00003000
++#define AR2313_CLOCKCTL1_PREDIVIDE_SHIFT 12
++#define AR2313_CLOCKCTL1_MULTIPLIER_MASK 0x001f0000
++#define AR2313_CLOCKCTL1_MULTIPLIER_SHIFT 16
++#define AR2313_CLOCKCTL1_DOUBLER_MASK 0x00000000
++
++
++/* AR531X_ENABLE register bit field definitions */
++#define AR531X_ENABLE_WLAN0 0x0001
++#define AR531X_ENABLE_ENET0 0x0002
++#define AR531X_ENABLE_ENET1 0x0004
++#define AR531X_ENABLE_UART_AND_WLAN1_PIO 0x0008 /* UART, and WLAN1 PIOs */
++#define AR531X_ENABLE_WLAN1_DMA 0x0010 /* WLAN1 DMAs */
++#define AR531X_ENABLE_WLAN1 \
++ (AR531X_ENABLE_UART_AND_WLAN1_PIO | AR531X_ENABLE_WLAN1_DMA)
++
++/* AR531X_REV register bit field definitions */
++#define AR531X_REV_WMAC_MAJ 0xf000
++#define AR531X_REV_WMAC_MAJ_S 12
++#define AR531X_REV_WMAC_MIN 0x0f00
++#define AR531X_REV_WMAC_MIN_S 8
++#define AR531X_REV_MAJ 0x00f0
++#define AR531X_REV_MAJ_S 4
++#define AR531X_REV_MIN 0x000f
++#define AR531X_REV_MIN_S 0
++#define AR531X_REV_CHIP (AR531X_REV_MAJ|AR531X_REV_MIN)
++
++/* Major revision numbers, bits 7..4 of Revision ID register */
++#define AR531X_REV_MAJ_AR5312 0x4
++#define AR531X_REV_MAJ_AR2313 0x5
++
++/* Minor revision numbers, bits 3..0 of Revision ID register */
++#define AR5312_REV_MIN_DUAL 0x0 /* Dual WLAN version */
++#define AR5312_REV_MIN_SINGLE 0x1 /* Single WLAN version */
++
++/* AR531X_FLASHCTL register bit field definitions */
++#define FLASHCTL_IDCY 0x0000000f /* Idle cycle turn around time */
++#define FLASHCTL_IDCY_S 0
++#define FLASHCTL_WST1 0x000003e0 /* Wait state 1 */
++#define FLASHCTL_WST1_S 5
++#define FLASHCTL_RBLE 0x00000400 /* Read byte lane enable */
++#define FLASHCTL_WST2 0x0000f800 /* Wait state 2 */
++#define FLASHCTL_WST2_S 11
++#define FLASHCTL_AC 0x00070000 /* Flash address check (added) */
++#define FLASHCTL_AC_S 16
++#define FLASHCTL_AC_128K 0x00000000
++#define FLASHCTL_AC_256K 0x00010000
++#define FLASHCTL_AC_512K 0x00020000
++#define FLASHCTL_AC_1M 0x00030000
++#define FLASHCTL_AC_2M 0x00040000
++#define FLASHCTL_AC_4M 0x00050000
++#define FLASHCTL_AC_8M 0x00060000
++#define FLASHCTL_AC_RES 0x00070000 /* 16MB is not supported */
++#define FLASHCTL_E 0x00080000 /* Flash bank enable (added) */
++#define FLASHCTL_BUSERR 0x01000000 /* Bus transfer error status flag */
++#define FLASHCTL_WPERR 0x02000000 /* Write protect error status flag */
++#define FLASHCTL_WP 0x04000000 /* Write protect */
++#define FLASHCTL_BM 0x08000000 /* Burst mode */
++#define FLASHCTL_MW 0x30000000 /* Memory width */
++#define FLASHCTL_MWx8 0x00000000 /* Memory width x8 */
++#define FLASHCTL_MWx16 0x10000000 /* Memory width x16 */
++#define FLASHCTL_MWx32 0x20000000 /* Memory width x32 (not supported) */
++#define FLASHCTL_ATNR 0x00000000 /* Access type == no retry */
++#define FLASHCTL_ATR 0x80000000 /* Access type == retry every */
++#define FLASHCTL_ATR4 0xc0000000 /* Access type == retry every 4 */
++
++/* ARM Flash Controller -- 3 flash banks with either x8 or x16 devices. */
++#define AR531X_FLASHCTL0 (AR531X_FLASHCTL + 0x00)
++#define AR531X_FLASHCTL1 (AR531X_FLASHCTL + 0x04)
++#define AR531X_FLASHCTL2 (AR531X_FLASHCTL + 0x08)
++
++/* ARM SDRAM Controller -- just enough to determine memory size */
++#define AR531X_MEM_CFG1 (AR531X_SDRAMCTL + 0x04)
++#define MEM_CFG1_AC0 0x00000700 /* bank 0: SDRAM addr check (added) */
++#define MEM_CFG1_AC0_S 8
++#define MEM_CFG1_AC1 0x00007000 /* bank 1: SDRAM addr check (added) */
++#define MEM_CFG1_AC1_S 12
++
++/* GPIO Address Map */
++#define AR531X_GPIO (AR531X_APBBASE + 0x2000)
++#define AR531X_GPIO_DO (AR531X_GPIO + 0x00) /* output register */
++#define AR531X_GPIO_DI (AR531X_GPIO + 0x04) /* intput register */
++#define AR531X_GPIO_CR (AR531X_GPIO + 0x08) /* control register */
++
++/* GPIO Control Register bit field definitions */
++#define AR531X_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
++#define AR531X_GPIO_CR_O(x) (0 << (x)) /* mask for output */
++#define AR531X_GPIO_CR_I(x) (1 << (x)) /* mask for input */
++#define AR531X_GPIO_CR_INT(x) (1 << ((x)+8)) /* mask for interrupt */
++#define AR531X_GPIO_CR_UART(x) (1 << ((x)+16)) /* uart multiplex */
++#define AR531X_NUM_GPIO 8
++
++
++#endif
++
+--- /dev/null
++++ b/arch/mips/ar231x/ar5312.c
+@@ -0,0 +1,563 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ */
++
++/*
++ * Platform devices for Atheros SoCs
++ */
++
++#include <linux/autoconf.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/types.h>
++#include <linux/string.h>
++#include <linux/mtd/physmap.h>
++#include <linux/platform_device.h>
++#include <linux/kernel.h>
++#include <linux/reboot.h>
++#include <linux/leds.h>
++#include <asm/bootinfo.h>
++#include <asm/reboot.h>
++#include <asm/time.h>
++#include <asm/irq.h>
++#include <asm/io.h>
++#include <gpio.h>
++
++#include <ar231x_platform.h>
++#include <ar5312_regs.h>
++#include <ar231x.h>
++#include "devices.h"
++#include "ar5312.h"
++
++#define IS_5312() (current_cpu_data.cputype != CPU_4KEC)
++
++static void
++ar5312_misc_irq_dispatch(void)
++{
++ unsigned int ar231x_misc_intrs = ar231x_read_reg(AR531X_ISR) & ar231x_read_reg(AR531X_IMR);
++
++ if (ar231x_misc_intrs & AR531X_ISR_TIMER) {
++ do_IRQ(AR531X_MISC_IRQ_TIMER);
++ (void)ar231x_read_reg(AR531X_TIMER);
++ } else if (ar231x_misc_intrs & AR531X_ISR_AHBPROC)
++ do_IRQ(AR531X_MISC_IRQ_AHB_PROC);
++ else if ((ar231x_misc_intrs & AR531X_ISR_UART0))
++ do_IRQ(AR531X_MISC_IRQ_UART0);
++ else if (ar231x_misc_intrs & AR531X_ISR_WD)
++ do_IRQ(AR531X_MISC_IRQ_WATCHDOG);
++ else
++ do_IRQ(AR531X_MISC_IRQ_NONE);
++}
++
++void
++ar5312_irq_dispatch(void)
++{
++ int pending = read_c0_status() & read_c0_cause();
++
++ if (pending & CAUSEF_IP2)
++ do_IRQ(AR5312_IRQ_WLAN0_INTRS);
++ else if (pending & CAUSEF_IP3)
++ do_IRQ(AR5312_IRQ_ENET0_INTRS);
++ else if (pending & CAUSEF_IP4)
++ do_IRQ(AR5312_IRQ_ENET1_INTRS);
++ else if (pending & CAUSEF_IP5)
++ do_IRQ(AR5312_IRQ_WLAN1_INTRS);
++ else if (pending & CAUSEF_IP6)
++ ar5312_misc_irq_dispatch();
++ else if (pending & CAUSEF_IP7)
++ do_IRQ(AR531X_IRQ_CPU_CLOCK);
++}
++
++
++/* Enable the specified AR531X_MISC_IRQ interrupt */
++static void
++ar5312_misc_intr_enable(unsigned int irq)
++{
++ unsigned int imr;
++
++ imr = ar231x_read_reg(AR531X_IMR);
++ imr |= (1 << (irq - AR531X_MISC_IRQ_BASE - 1));
++ ar231x_write_reg(AR531X_IMR, imr);
++}
++
++/* Disable the specified AR531X_MISC_IRQ interrupt */
++static void
++ar5312_misc_intr_disable(unsigned int irq)
++{
++ unsigned int imr;
++
++ imr = ar231x_read_reg(AR531X_IMR);
++ imr &= ~(1 << (irq - AR531X_MISC_IRQ_BASE - 1));
++ ar231x_write_reg(AR531X_IMR, imr);
++ ar231x_read_reg(AR531X_IMR); /* flush write buffer */
++}
++
++static unsigned int
++ar5312_misc_intr_startup(unsigned int irq)
++{
++ ar5312_misc_intr_enable(irq);
++ return 0;
++}
++
++static void
++ar5312_misc_intr_end(unsigned int irq)
++{
++ if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
++ ar5312_misc_intr_enable(irq);
++}
++
++static struct irq_chip ar5312_misc_intr_controller = {
++ .name = "AR5312-MISC",
++ .startup = ar5312_misc_intr_startup,
++ .shutdown = ar5312_misc_intr_disable,
++ .enable = ar5312_misc_intr_enable,
++ .disable = ar5312_misc_intr_disable,
++ .ack = ar5312_misc_intr_disable,
++ .end = ar5312_misc_intr_end,
++};
++
++
++static irqreturn_t ar5312_ahb_proc_handler(int cpl, void *dev_id)
++{
++ u32 proc1 = ar231x_read_reg(AR531X_PROC1);
++ u32 procAddr = ar231x_read_reg(AR531X_PROCADDR); /* clears error state */
++ u32 dma1 = ar231x_read_reg(AR531X_DMA1);
++ u32 dmaAddr = ar231x_read_reg(AR531X_DMAADDR); /* clears error state */
++
++ printk("AHB interrupt: PROCADDR=0x%8.8x PROC1=0x%8.8x DMAADDR=0x%8.8x DMA1=0x%8.8x\n",
++ procAddr, proc1, dmaAddr, dma1);
++
++ machine_restart("AHB error"); /* Catastrophic failure */
++ return IRQ_HANDLED;
++}
++
++
++static struct irqaction ar5312_ahb_proc_interrupt = {
++ .handler = ar5312_ahb_proc_handler,
++ .flags = IRQF_DISABLED,
++ .name = "ar5312_ahb_proc_interrupt",
++};
++
++
++static struct irqaction cascade = {
++ .handler = no_action,
++ .flags = IRQF_DISABLED,
++ .name = "cascade",
++};
++
++void __init ar5312_irq_init(void)
++{
++ int i;
++
++ if (!IS_5312())
++ return;
++
++ ar231x_irq_dispatch = ar5312_irq_dispatch;
++ for (i = 0; i < AR531X_MISC_IRQ_COUNT; i++) {
++ int irq = AR531X_MISC_IRQ_BASE + i;
++ irq_desc[irq].status = IRQ_DISABLED;
++ irq_desc[irq].action = NULL;
++ irq_desc[irq].depth = 1;
++ irq_desc[irq].chip = &ar5312_misc_intr_controller;
++ }
++ setup_irq(AR531X_MISC_IRQ_AHB_PROC, &ar5312_ahb_proc_interrupt);
++ setup_irq(AR5312_IRQ_MISC_INTRS, &cascade);
++}
++
++const struct ar231x_gpiodev ar5312_gpiodev;
++
++static u32
++ar5312_gpio_get_output(void)
++{
++ u32 reg;
++ reg = ~(ar231x_read_reg(AR531X_GPIO_CR));
++ reg &= ar5312_gpiodev.valid_mask;
++ return reg;
++}
++
++static u32
++ar5312_gpio_set_output(u32 mask, u32 val)
++{
++ u32 reg;
++
++ reg = ar231x_read_reg(AR531X_GPIO_CR);
++ reg |= mask;
++ reg &= ~val;
++ ar231x_write_reg(AR531X_GPIO_CR, reg);
++ return reg;
++}
++
++static u32
++ar5312_gpio_get(void)
++{
++ u32 reg;
++ reg = ar231x_read_reg(AR531X_GPIO_DI);
++ reg &= ar5312_gpiodev.valid_mask;
++ return reg;
++}
++
++static u32
++ar5312_gpio_set(u32 mask, u32 value)
++{
++ u32 reg;
++ reg = ar231x_read_reg(AR531X_GPIO_DO);
++ reg &= ~mask;
++ reg |= value;
++ ar231x_write_reg(AR531X_GPIO_DO, reg);
++ return reg;
++}
++
++const struct ar231x_gpiodev ar5312_gpiodev = {
++ .valid_mask = (1 << 8) - 1,
++ .get_output = ar5312_gpio_get_output,
++ .set_output = ar5312_gpio_set_output,
++ .get = ar5312_gpio_get,
++ .set = ar5312_gpio_set,
++};
++
++static struct physmap_flash_data ar5312_flash_data = {
++ .width = 2,
++};
++
++static struct resource ar5312_flash_resource = {
++ .start = AR531X_FLASH,
++ .end = AR531X_FLASH + 0x800000 - 1,
++ .flags = IORESOURCE_MEM,
++};
++
++static struct ar231x_eth ar5312_eth0_data = {
++ .reset_base = AR531X_RESET,
++ .reset_mac = AR531X_RESET_ENET0,
++ .reset_phy = AR531X_RESET_EPHY0,
++ .phy_base = KSEG1ADDR(AR531X_ENET0),
++ .config = &ar231x_board,
++};
++
++static struct ar231x_eth ar5312_eth1_data = {
++ .reset_base = AR531X_RESET,
++ .reset_mac = AR531X_RESET_ENET1,
++ .reset_phy = AR531X_RESET_EPHY1,
++ .phy_base = KSEG1ADDR(AR531X_ENET1),
++ .config = &ar231x_board,
++};
++
++static struct platform_device ar5312_physmap_flash = {
++ .name = "physmap-flash",
++ .id = 0,
++ .dev.platform_data = &ar5312_flash_data,
++ .resource = &ar5312_flash_resource,
++ .num_resources = 1,
++};
++
++#ifdef CONFIG_LEDS_GPIO
++static struct gpio_led ar5312_leds[] = {
++ { .name = "wlan", .gpio = 0, .active_low = 1, },
++};
++
++static const struct gpio_led_platform_data ar5312_led_data = {
++ .num_leds = ARRAY_SIZE(ar5312_leds),
++ .leds = (void *) ar5312_leds,
++};
++
++static struct platform_device ar5312_gpio_leds = {
++ .name = "leds-gpio",
++ .id = -1,
++ .dev.platform_data = (void *) &ar5312_led_data,
++ .num_resources = 1,
++};
++#endif
++
++/*
++ * NB: This mapping size is larger than the actual flash size,
++ * but this shouldn't be a problem here, because the flash
++ * will simply be mapped multiple times.
++ */
++static char __init *ar5312_flash_limit(void)
++{
++ u32 ctl;
++ /*
++ * Configure flash bank 0.
++ * Assume 8M window size. Flash will be aliased if it's smaller
++ */
++ ctl = FLASHCTL_E |
++ FLASHCTL_AC_8M |
++ FLASHCTL_RBLE |
++ (0x01 << FLASHCTL_IDCY_S) |
++ (0x07 << FLASHCTL_WST1_S) |
++ (0x07 << FLASHCTL_WST2_S) |
++ (ar231x_read_reg(AR531X_FLASHCTL0) & FLASHCTL_MW);
++
++ ar231x_write_reg(AR531X_FLASHCTL0, ctl);
++
++ /* Disable other flash banks */
++ ar231x_write_reg(AR531X_FLASHCTL1,
++ ar231x_read_reg(AR531X_FLASHCTL1) & ~(FLASHCTL_E | FLASHCTL_AC));
++
++ ar231x_write_reg(AR531X_FLASHCTL2,
++ ar231x_read_reg(AR531X_FLASHCTL2) & ~(FLASHCTL_E | FLASHCTL_AC));
++
++ return (char *) KSEG1ADDR(AR531X_FLASH + 0x800000);
++}
++
++int __init ar5312_init_devices(void)
++{
++ struct ar231x_boarddata *config;
++ u32 fctl = 0;
++ const u8 *radio;
++ u8 *c;
++
++ if (!IS_5312())
++ return 0;
++
++ /* Locate board/radio config data */
++ ar231x_find_config(ar5312_flash_limit());
++ config = ar231x_board.config;
++
++
++ /*
++ * Chip IDs and hardware detection for some Atheros
++ * models are really broken!
++ *
++ * Atheros uses a disabled WMAC0 and Silicon ID of AR5312
++ * as indication for AR2312, which is otherwise
++ * indistinguishable from the real AR5312.
++ */
++ if (ar231x_board.radio) {
++ radio = ar231x_board.radio + AR531X_RADIO_MASK_OFF;
++ if ((*((const u32 *) radio) & AR531X_RADIO0_MASK) == 0)
++ config->flags |= BD_ISCASPER;
++ } else
++ radio = NULL;
++
++ /* AR2313 has CPU minor rev. 10 */
++ if ((current_cpu_data.processor_id & 0xff) == 0x0a)
++ ar231x_devtype = DEV_TYPE_AR2313;
++
++ /* AR2312 shares the same Silicon ID as AR5312 */
++ else if (config->flags & BD_ISCASPER)
++ ar231x_devtype = DEV_TYPE_AR2312;
++
++ /* Everything else is probably AR5312 or compatible */
++ else
++ ar231x_devtype = DEV_TYPE_AR5312;
++
++ /* fixup flash width */
++ fctl = ar231x_read_reg(AR531X_FLASHCTL) & FLASHCTL_MW;
++ switch (fctl) {
++ case FLASHCTL_MWx16:
++ ar5312_flash_data.width = 2;
++ break;
++ case FLASHCTL_MWx8:
++ default:
++ ar5312_flash_data.width = 1;
++ break;
++ }
++
++ platform_device_register(&ar5312_physmap_flash);
++
++#ifdef CONFIG_LEDS_GPIO
++ ar5312_leds[0].gpio = config->sysLedGpio;
++ platform_device_register(&ar5312_gpio_leds);
++#endif
++
++ /* Fix up MAC addresses if necessary */
++ if (!memcmp(config->enet0_mac, "\xff\xff\xff\xff\xff\xff", 6))
++ memcpy(config->enet0_mac, config->enet1_mac, 6);
++
++ /* If ENET0 and ENET1 have the same mac address,
++ * increment the one from ENET1 */
++ if (memcmp(config->enet0_mac, config->enet1_mac, 6) == 0) {
++ c = config->enet1_mac + 5;
++ while ((c >= config->enet1_mac) && !(++(*c)))
++ c--;
++ }
++
++ switch(ar231x_devtype) {
++ case DEV_TYPE_AR5312:
++ ar5312_eth0_data.macaddr = config->enet0_mac;
++ ar231x_add_ethernet(0, KSEG1ADDR(AR531X_ENET0),
++ AR5312_IRQ_ENET0_INTRS, &ar5312_eth0_data);
++
++ ar5312_eth1_data.macaddr = config->enet1_mac;
++ ar231x_add_ethernet(1, KSEG1ADDR(AR531X_ENET1),
++ AR5312_IRQ_ENET1_INTRS, &ar5312_eth1_data);
++
++ if (!ar231x_board.radio)
++ return 0;
++
++ if (*((u32 *) ar231x_board.radio) & AR531X_RADIO0_MASK)
++ ar231x_add_wmac(0, AR531X_WLAN0,
++ AR5312_IRQ_WLAN0_INTRS);
++
++ break;
++ /*
++ * AR2312/3 ethernet uses the PHY of ENET0, but the MAC
++ * of ENET1. Atheros calls it 'twisted' for a reason :)
++ */
++ case DEV_TYPE_AR2312:
++ case DEV_TYPE_AR2313:
++ ar5312_eth1_data.phy_base = ar5312_eth0_data.phy_base;
++ ar5312_eth1_data.reset_phy = ar5312_eth0_data.reset_phy;
++ ar5312_eth1_data.macaddr = config->enet0_mac;
++ ar231x_add_ethernet(0, KSEG1ADDR(AR531X_ENET1),
++ AR5312_IRQ_ENET1_INTRS, &ar5312_eth1_data);
++
++ if (!ar231x_board.radio)
++ return 0;
++ break;
++ default:
++ break;
++ }
++
++ if (*((u32 *) ar231x_board.radio) & AR531X_RADIO1_MASK)
++ ar231x_add_wmac(1, AR531X_WLAN1,
++ AR5312_IRQ_WLAN1_INTRS);
++
++ return 0;
++}
++
++
++static void ar5312_restart(char *command)
++{
++ /* reset the system */
++ local_irq_disable();
++ while(1) {
++ ar231x_write_reg(AR531X_RESET, AR531X_RESET_SYSTEM);
++ }
++}
++
++
++/*
++ * This table is indexed by bits 5..4 of the CLOCKCTL1 register
++ * to determine the predevisor value.
++ */
++static int __initdata CLOCKCTL1_PREDIVIDE_TABLE[4] = {
++ 1,
++ 2,
++ 4,
++ 5
++};
++
++
++static int __init
++ar5312_cpu_frequency(void)
++{
++ unsigned int result;
++ unsigned int predivide_mask, predivide_shift;
++ unsigned int multiplier_mask, multiplier_shift;
++ unsigned int clockCtl1, preDivideSelect, preDivisor, multiplier;
++ unsigned int doubler_mask;
++ u16 devid;
++
++ /* Trust the bootrom's idea of cpu frequency. */
++ if ((result = ar231x_read_reg(AR5312_SCRATCH)))
++ return result;
++
++ devid = ar231x_board.devid;
++ devid &= AR531X_REV_MAJ;
++ devid >>= AR531X_REV_MAJ_S;
++ if (devid == AR531X_REV_MAJ_AR2313) {
++ predivide_mask = AR2313_CLOCKCTL1_PREDIVIDE_MASK;
++ predivide_shift = AR2313_CLOCKCTL1_PREDIVIDE_SHIFT;
++ multiplier_mask = AR2313_CLOCKCTL1_MULTIPLIER_MASK;
++ multiplier_shift = AR2313_CLOCKCTL1_MULTIPLIER_SHIFT;
++ doubler_mask = AR2313_CLOCKCTL1_DOUBLER_MASK;
++ } else { /* AR5312 and AR2312 */
++ predivide_mask = AR5312_CLOCKCTL1_PREDIVIDE_MASK;
++ predivide_shift = AR5312_CLOCKCTL1_PREDIVIDE_SHIFT;
++ multiplier_mask = AR5312_CLOCKCTL1_MULTIPLIER_MASK;
++ multiplier_shift = AR5312_CLOCKCTL1_MULTIPLIER_SHIFT;
++ doubler_mask = AR5312_CLOCKCTL1_DOUBLER_MASK;
++ }
++
++ /*
++ * Clocking is derived from a fixed 40MHz input clock.
++ *
++ * cpuFreq = InputClock * MULT (where MULT is PLL multiplier)
++ * sysFreq = cpuFreq / 4 (used for APB clock, serial,
++ * flash, Timer, Watchdog Timer)
++ *
++ * cntFreq = cpuFreq / 2 (use for CPU count/compare)
++ *
++ * So, for example, with a PLL multiplier of 5, we have
++ *
++ * cpuFreq = 200MHz
++ * sysFreq = 50MHz
++ * cntFreq = 100MHz
++ *
++ * We compute the CPU frequency, based on PLL settings.
++ */
++
++ clockCtl1 = ar231x_read_reg(AR5312_CLOCKCTL1);
++ preDivideSelect = (clockCtl1 & predivide_mask) >> predivide_shift;
++ preDivisor = CLOCKCTL1_PREDIVIDE_TABLE[preDivideSelect];
++ multiplier = (clockCtl1 & multiplier_mask) >> multiplier_shift;
++
++ if (clockCtl1 & doubler_mask) {
++ multiplier = multiplier << 1;
++ }
++ return (40000000 / preDivisor) * multiplier;
++}
++
++static inline int
++ar5312_sys_frequency(void)
++{
++ return ar5312_cpu_frequency() / 4;
++}
++
++void __init
++ar5312_time_init(void)
++{
++ if (!IS_5312())
++ return;
++
++ mips_hpt_frequency = ar5312_cpu_frequency() / 2;
++}
++
++
++void __init
++ar5312_prom_init(void)
++{
++ u32 memsize, memcfg, bank0AC, bank1AC;
++ u32 devid;
++
++ if (!IS_5312())
++ return;
++
++ devid = ar231x_read_reg(AR531X_REV);
++ devid &= AR531X_REV_MAJ | AR531X_REV_MIN;
++
++ /* Detect memory size */
++ memcfg = ar231x_read_reg(AR531X_MEM_CFG1);
++ bank0AC = (memcfg & MEM_CFG1_AC0) >> MEM_CFG1_AC0_S;
++ bank1AC = (memcfg & MEM_CFG1_AC1) >> MEM_CFG1_AC1_S;
++ memsize = (bank0AC ? (1 << (bank0AC+1)) : 0)
++ + (bank1AC ? (1 << (bank1AC+1)) : 0);
++ memsize <<= 20;
++ add_memory_region(0, memsize, BOOT_MEM_RAM);
++ ar231x_gpiodev = &ar5312_gpiodev;
++ ar231x_board.devid = (u16) devid;
++}
++
++void __init
++ar5312_plat_setup(void)
++{
++ if (!IS_5312())
++ return;
++
++ /* Clear any lingering AHB errors */
++ ar231x_read_reg(AR531X_PROCADDR);
++ ar231x_read_reg(AR531X_DMAADDR);
++ ar231x_write_reg(AR531X_WD_CTRL, AR531X_WD_CTRL_IGNORE_EXPIRATION);
++
++ _machine_restart = ar5312_restart;
++ ar231x_serial_setup(KSEG1ADDR(AR531X_UART0), ar5312_sys_frequency());
++}
++
+--- /dev/null
++++ b/arch/mips/ar231x/pci.c
+@@ -0,0 +1,231 @@
++/*
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * as published by the Free Software Foundation; either version 2
++ * of the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
++ */
++
++#include <linux/types.h>
++#include <linux/pci.h>
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/mm.h>
++#include <linux/spinlock.h>
++#include <linux/delay.h>
++#include <linux/irq.h>
++#include <asm/bootinfo.h>
++#include <asm/paccess.h>
++#include <asm/irq_cpu.h>
++#include <asm/io.h>
++#include <ar231x_platform.h>
++#include <ar231x.h>
++#include <ar2315_regs.h>
++
++#define AR531X_MEM_BASE 0x80800000UL
++#define AR531X_MEM_SIZE 0x00ffffffUL
++#define AR531X_IO_SIZE 0x00007fffUL
++
++#define IS_2315() (current_cpu_data.cputype == CPU_4KEC)
++
++static unsigned long configspace;
++
++static int config_access(int devfn, int where, int size, u32 *ptr, bool write)
++{
++ unsigned long flags;
++ int func = PCI_FUNC(devfn);
++ int dev = PCI_SLOT(devfn);
++ u32 value = 0;
++ int err = 0;
++ u32 addr;
++
++ if (((dev != 0) && (dev != 3)) || (func > 2))
++ return PCIBIOS_DEVICE_NOT_FOUND;
++
++ /* Select Configuration access */
++ local_irq_save(flags);
++ ar231x_mask_reg(AR2315_PCI_MISC_CONFIG, 0, AR2315_PCIMISC_CFG_SEL);
++ mb();
++
++ addr = (u32) configspace + (1 << (13 + dev)) + (func << 8) + where;
++ if (size == 1)
++ addr ^= 0x3;
++ else if (size == 2)
++ addr ^= 0x2;
++
++ if (write) {
++ value = *ptr;
++ if (size == 1)
++ err = put_dbe(value, (u8 *) addr);
++ else if (size == 2)
++ err = put_dbe(value, (u16 *) addr);
++ else if (size == 4)
++ err = put_dbe(value, (u32 *) addr);
++ } else {
++ if (size == 1)
++ err = get_dbe(value, (u8 *) addr);
++ else if (size == 2)
++ err = get_dbe(value, (u16 *) addr);
++ else if (size == 4)
++ err = get_dbe(value, (u32 *) addr);
++ if (err)
++ *ptr = 0xffffffff;
++ else
++ *ptr = value;
++ }
++
++ /* Select Memory access */
++ ar231x_mask_reg(AR2315_PCI_MISC_CONFIG, AR2315_PCIMISC_CFG_SEL, 0);
++ local_irq_restore(flags);
++
++ return (err ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL);
++}
++
++static int ar231x_pci_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 * value)
++{
++ return config_access(devfn, where, size, value, 0);
++}
++
++static int ar231x_pci_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value)
++{
++ return config_access(devfn, where, size, &value, 1);
++}
++
++struct pci_ops ar231x_pci_ops = {
++ .read = ar231x_pci_read,
++ .write = ar231x_pci_write,
++};
++
++static struct resource ar231x_mem_resource = {
++ .name = "AR531x PCI MEM",
++ .start = AR531X_MEM_BASE,
++ .end = AR531X_MEM_BASE + AR531X_MEM_SIZE - AR531X_IO_SIZE - 1 + 0x4000000,
++ .flags = IORESOURCE_MEM,
++};
++
++static struct resource ar231x_io_resource = {
++ .name = "AR531x PCI I/O",
++ .start = AR531X_MEM_BASE + AR531X_MEM_SIZE - AR531X_IO_SIZE,
++ .end = AR531X_MEM_BASE + AR531X_MEM_SIZE - 1,
++ .flags = IORESOURCE_IO,
++};
++
++struct pci_controller ar231x_pci_controller = {
++ .pci_ops = &ar231x_pci_ops,
++ .mem_resource = &ar231x_mem_resource,
++ .io_resource = &ar231x_io_resource,
++ .mem_offset = 0x00000000UL,
++ .io_offset = 0x00000000UL,
++};
++
++int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
++{
++ return AR2315_IRQ_LCBUS_PCI;
++}
++
++int pcibios_plat_dev_init(struct pci_dev *dev)
++{
++ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 5);
++ pci_write_config_word(dev, 0x40, 0);
++
++ /* Clear any pending Abort or external Interrupts
++ * and enable interrupt processing */
++ ar231x_mask_reg(AR2315_PCI_INTEN_REG, AR2315_PCI_INT_ENABLE, 0);
++ ar231x_write_reg(AR2315_PCI_INT_STATUS, (AR2315_PCI_ABORT_INT | AR2315_PCI_EXT_INT));
++ ar231x_write_reg(AR2315_PCI_INT_MASK, (AR2315_PCI_ABORT_INT | AR2315_PCI_EXT_INT));
++ ar231x_mask_reg(AR2315_PCI_INTEN_REG, 0, AR2315_PCI_INT_ENABLE);
++
++ return 0;
++}
++
++static void
++ar2315_pci_fixup(struct pci_dev *dev)
++{
++ unsigned int devfn = dev->devfn;
++
++ if (dev->bus->number != 0)
++ return;
++
++ /* Only fix up the PCI host settings */
++ if ((PCI_SLOT(devfn) != 3) || (PCI_FUNC(devfn) != 0))
++ return;
++
++ /* Fix up MBARs */
++ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, HOST_PCI_MBAR0);
++ pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, HOST_PCI_MBAR1);
++ pci_write_config_dword(dev, PCI_BASE_ADDRESS_2, HOST_PCI_MBAR2);
++ pci_write_config_dword(dev, PCI_COMMAND,
++ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_SPECIAL |
++ PCI_COMMAND_INVALIDATE | PCI_COMMAND_PARITY | PCI_COMMAND_SERR |
++ PCI_COMMAND_FAST_BACK);
++}
++DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, ar2315_pci_fixup);
++
++static int __init
++ar2315_pci_init(void)
++{
++ u32 reg;
++
++ if (!IS_2315())
++ return -ENODEV;
++
++ configspace = (unsigned long) ioremap_nocache(0x80000000, 1*1024*1024); /* Remap PCI config space */
++ ar231x_pci_controller.io_map_base =
++ (unsigned long) ioremap_nocache(AR531X_MEM_BASE + AR531X_MEM_SIZE, AR531X_IO_SIZE);
++ set_io_port_base(ar231x_pci_controller.io_map_base); /* PCI I/O space */
++
++ reg = ar231x_mask_reg(AR2315_RESET, 0, AR2315_RESET_PCIDMA);
++ msleep(10);
++
++ reg &= ~AR2315_RESET_PCIDMA;
++ ar231x_write_reg(AR2315_RESET, reg);
++ msleep(10);
++
++ ar231x_mask_reg(AR2315_ENDIAN_CTL, 0,
++ AR2315_CONFIG_PCIAHB | AR2315_CONFIG_PCIAHB_BRIDGE);
++
++ ar231x_write_reg(AR2315_PCICLK, AR2315_PCICLK_PLLC_CLKM |
++ (AR2315_PCICLK_IN_FREQ_DIV_6 << AR2315_PCICLK_DIV_S));
++ ar231x_mask_reg(AR2315_AHB_ARB_CTL, 0, AR2315_ARB_PCI);
++ ar231x_mask_reg(AR2315_IF_CTL, AR2315_IF_PCI_CLK_MASK | AR2315_IF_MASK,
++ AR2315_IF_PCI | AR2315_IF_PCI_HOST | AR2315_IF_PCI_INTR |
++ (AR2315_IF_PCI_CLK_OUTPUT_CLK << AR2315_IF_PCI_CLK_SHIFT));
++
++ /* Reset the PCI bus by setting bits 5-4 in PCI_MCFG */
++ ar231x_mask_reg(AR2315_PCI_MISC_CONFIG, AR2315_PCIMISC_RST_MODE,
++ AR2315_PCIRST_LOW);
++ msleep(100);
++
++ /* Bring the PCI out of reset */
++ ar231x_mask_reg(AR2315_PCI_MISC_CONFIG, AR2315_PCIMISC_RST_MODE,
++ AR2315_PCIRST_HIGH | AR2315_PCICACHE_DIS | 0x8);
++
++ ar231x_write_reg(AR2315_PCI_UNCACHE_CFG,
++ 0x1E | /* 1GB uncached */
++ (1 << 5) | /* Enable uncached */
++ (0x2 << 30) /* Base: 0x80000000 */
++ );
++ ar231x_read_reg(AR2315_PCI_UNCACHE_CFG);
++
++ msleep(500);
++
++ /* dirty hack - anyone with a datasheet that knows the memory map ? */
++ ioport_resource.start = 0x10000000;
++ ioport_resource.end = 0xffffffff;
++ iomem_resource.start = 0x10000000;
++ iomem_resource.end = 0xffffffff;
++
++ register_pci_controller(&ar231x_pci_controller);
++
++ return 0;
++}
++
++arch_initcall(ar2315_pci_init);
+--- /dev/null
++++ b/arch/mips/ar231x/ar2315.c
+@@ -0,0 +1,688 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
++ */
++
++/*
++ * Platform devices for Atheros SoCs
++ */
++
++#include <linux/autoconf.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/types.h>
++#include <linux/string.h>
++#include <linux/platform_device.h>
++#include <linux/kernel.h>
++#include <linux/reboot.h>
++#include <linux/delay.h>
++#include <linux/leds.h>
++#include <asm/bootinfo.h>
++#include <asm/reboot.h>
++#include <asm/time.h>
++#include <asm/irq.h>
++#include <asm/io.h>
++#include <asm/gpio.h>
++
++#include <ar231x_platform.h>
++#include <ar2315_regs.h>
++#include <ar231x.h>
++#include "devices.h"
++#include "ar2315.h"
++
++#define IS_2315() (current_cpu_data.cputype == CPU_4KEC)
++
++static u32 gpiointmask = 0, gpiointval = 0;
++
++static inline void ar2315_gpio_irq(void)
++{
++ u32 pend;
++ int bit;
++
++ /* only do one gpio interrupt at a time */
++ pend = (ar231x_read_reg(AR2315_GPIO_DI) ^ gpiointval) & gpiointmask;
++ if (!pend)
++ return;
++
++ bit = fls(pend);
++ pend ^= (1 << bit);
++ gpiointval ^= (1 << bit);
++
++ /* ACK the interrupt only if we handled all bits */
++ if (!pend)
++ ar231x_write_reg(AR2315_ISR, ar231x_read_reg(AR2315_IMR) | ~AR2315_ISR_GPIO);
++
++ do_IRQ(AR531X_GPIO_IRQ_BASE + fls(pend) - 1);
++}
++
++#ifdef CONFIG_ATHEROS_AR2315_PCI
++static inline void pci_abort_irq(void)
++{
++ ar231x_write_reg(AR2315_PCI_INT_STATUS, AR2315_PCI_ABORT_INT);
++}
++
++static inline void pci_ack_irq(void)
++{
++ ar231x_write_reg(AR2315_PCI_INT_STATUS, AR2315_PCI_EXT_INT);
++}
++
++void ar2315_pci_irq(int irq)
++{
++ if (ar231x_read_reg(AR2315_PCI_INT_STATUS) == AR2315_PCI_ABORT_INT)
++ pci_abort_irq();
++ else {
++ do_IRQ(irq);
++ pci_ack_irq();
++ }
++}
++#endif /* CONFIG_ATHEROS_AR2315_PCI */
++
++/*
++ * Called when an interrupt is received, this function
++ * determines exactly which interrupt it was, and it
++ * invokes the appropriate handler.
++ *
++ * Implicitly, we also define interrupt priority by
++ * choosing which to dispatch first.
++ */
++static void
++ar2315_irq_dispatch(void)
++{
++ int pending = read_c0_status() & read_c0_cause();
++
++ if (pending & CAUSEF_IP3)
++ do_IRQ(AR2315_IRQ_WLAN0_INTRS);
++ else if (pending & CAUSEF_IP4)
++ do_IRQ(AR2315_IRQ_ENET0_INTRS);
++#ifdef CONFIG_ATHEROS_AR2315_PCI
++ else if (pending & CAUSEF_IP5)
++ ar2315_pci_irq(AR2315_IRQ_LCBUS_PCI);
++#endif
++ else if (pending & CAUSEF_IP2) {
++ unsigned int misc_intr = ar231x_read_reg(AR2315_ISR) & ar231x_read_reg(AR2315_IMR);
++
++ if (misc_intr & AR2315_ISR_SPI)
++ do_IRQ(AR531X_MISC_IRQ_SPI);
++ else if (misc_intr & AR2315_ISR_TIMER)
++ do_IRQ(AR531X_MISC_IRQ_TIMER);
++ else if (misc_intr & AR2315_ISR_AHB)
++ do_IRQ(AR531X_MISC_IRQ_AHB_PROC);
++ else if (misc_intr & AR2315_ISR_GPIO)
++ ar2315_gpio_irq();
++ else if (misc_intr & AR2315_ISR_UART0)
++ do_IRQ(AR531X_MISC_IRQ_UART0);
++ else if (misc_intr & AR2315_ISR_WD)
++ do_IRQ(AR531X_MISC_IRQ_WATCHDOG);
++ else
++ do_IRQ(AR531X_MISC_IRQ_NONE);
++ } else if (pending & CAUSEF_IP7)
++ do_IRQ(AR531X_IRQ_CPU_CLOCK);
++}
++
++static void ar2315_set_gpiointmask(int gpio, int level)
++{
++ u32 reg;
++
++
++ reg = ar231x_read_reg(AR2315_GPIO_INT);
++ reg &= ~(AR2315_GPIO_INT_M | AR2315_GPIO_INT_LVL_M);
++ reg |= gpio | AR2315_GPIO_INT_LVL(level);
++ ar231x_write_reg(AR2315_GPIO_INT, reg);
++}
++
++static void ar2315_gpio_intr_enable(unsigned int irq)
++{
++ unsigned int gpio = irq - AR531X_GPIO_IRQ_BASE;
++ u32 reg;
++
++ gpiointmask &= ~(1 << gpio);
++
++ /* reconfigure GPIO line as input */
++ reg = ar231x_read_reg(AR2315_GPIO_CR);
++ reg &= ~(AR2315_GPIO_CR_M(gpio));
++ reg |= AR2315_GPIO_CR_I(gpio);
++ ar231x_write_reg(AR2315_GPIO_CR, reg);
++
++ /* Enable interrupt with edge detection */
++ ar2315_set_gpiointmask(gpio, 3);
++}
++
++static void ar2315_gpio_intr_disable(unsigned int irq)
++{
++ unsigned int gpio = irq - AR531X_GPIO_IRQ_BASE;
++
++ gpiointmask |= (1 << gpio);
++
++ /* Disable interrupt */
++ ar2315_set_gpiointmask(gpio, 0);
++}
++
++static struct irq_chip ar2315_gpio_intr_controller = {
++ .typename = "AR2315-GPIO",
++ .disable = ar2315_gpio_intr_disable,
++ .ack = ar2315_gpio_intr_disable,
++ .mask_ack = ar2315_gpio_intr_disable,
++ .unmask = ar2315_gpio_intr_enable,
++ .eoi = ar2315_gpio_intr_enable,
++};
++
++static void
++ar2315_misc_intr_enable(unsigned int irq)
++{
++ unsigned int imr;
++
++ imr = ar231x_read_reg(AR2315_IMR);
++ switch(irq) {
++ case AR531X_MISC_IRQ_SPI:
++ imr |= AR2315_ISR_SPI;
++ break;
++ case AR531X_MISC_IRQ_TIMER:
++ imr |= AR2315_ISR_TIMER;
++ break;
++ case AR531X_MISC_IRQ_AHB_PROC:
++ imr |= AR2315_ISR_AHB;
++ break;
++ case AR531X_MISC_IRQ_GPIO:
++ imr |= AR2315_ISR_GPIO;
++ break;
++ case AR531X_MISC_IRQ_UART0:
++ imr |= AR2315_ISR_UART0;
++ break;
++ case AR531X_MISC_IRQ_WATCHDOG:
++ imr |= AR2315_ISR_WD;
++ break;
++ default:
++ break;
++ }
++ ar231x_write_reg(AR2315_IMR, imr);
++}
++
++static void
++ar2315_misc_intr_disable(unsigned int irq)
++{
++ unsigned int imr;
++
++ imr = ar231x_read_reg(AR2315_IMR);
++ switch(irq) {
++ case AR531X_MISC_IRQ_SPI:
++ imr &= ~AR2315_ISR_SPI;
++ break;
++ case AR531X_MISC_IRQ_TIMER:
++ imr &= ~AR2315_ISR_TIMER;
++ break;
++ case AR531X_MISC_IRQ_AHB_PROC:
++ imr &= ~AR2315_ISR_AHB;
++ break;
++ case AR531X_MISC_IRQ_GPIO:
++ imr &= ~AR2315_ISR_GPIO;
++ break;
++ case AR531X_MISC_IRQ_UART0:
++ imr &= ~AR2315_ISR_UART0;
++ break;
++ case AR531X_MISC_IRQ_WATCHDOG:
++ imr &= ~AR2315_ISR_WD;
++ break;
++ default:
++ break;
++ }
++ ar231x_write_reg(AR2315_IMR, imr);
++}
++
++static unsigned int
++ar2315_misc_intr_startup(unsigned int irq)
++{
++ ar2315_misc_intr_enable(irq);
++ return 0;
++}
++
++static void
++ar2315_misc_intr_end(unsigned int irq)
++{
++ if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
++ ar2315_misc_intr_enable(irq);
++}
++
++
++static struct irq_chip ar2315_misc_intr_controller = {
++ .typename = "AR2315-MISC",
++ .startup = ar2315_misc_intr_startup,
++ .shutdown = ar2315_misc_intr_disable,
++ .enable = ar2315_misc_intr_enable,
++ .disable = ar2315_misc_intr_disable,
++ .ack = ar2315_misc_intr_disable,
++ .end = ar2315_misc_intr_end,
++};
++
++static irqreturn_t ar2315_ahb_proc_handler(int cpl, void *dev_id)
++{
++ ar231x_write_reg(AR2315_AHB_ERR0, AHB_ERROR_DET);
++ ar231x_read_reg(AR2315_AHB_ERR1);
++
++ printk(KERN_ERR "AHB fatal error\n");
++ machine_restart("AHB error"); /* Catastrophic failure */
++
++ return IRQ_HANDLED;
++}
++
++static struct irqaction ar2315_ahb_proc_interrupt = {
++ .handler = ar2315_ahb_proc_handler,
++ .flags = IRQF_DISABLED,
++ .name = "ar2315_ahb_proc_interrupt",
++};
++
++static struct irqaction cascade = {
++ .handler = no_action,
++ .flags = IRQF_DISABLED,
++ .name = "cascade",
++};
++
++void
++ar2315_irq_init(void)
++{
++ int i;
++
++ ar231x_irq_dispatch = ar2315_irq_dispatch;
++ gpiointval = ar231x_read_reg(AR2315_GPIO_DI);
++ for (i = 0; i < AR531X_MISC_IRQ_COUNT; i++) {
++ int irq = AR531X_MISC_IRQ_BASE + i;
++ irq_desc[irq].status = IRQ_DISABLED;
++ irq_desc[irq].action = NULL;
++ irq_desc[irq].depth = 1;
++ irq_desc[irq].chip = &ar2315_misc_intr_controller;
++ }
++ for (i = 0; i < AR531X_GPIO_IRQ_COUNT; i++) {
++ int irq = AR531X_GPIO_IRQ_BASE + i;
++ irq_desc[irq].status = IRQ_DISABLED;
++ irq_desc[irq].action = NULL;
++ irq_desc[irq].depth = 1;
++ irq_desc[irq].chip = &ar2315_gpio_intr_controller;
++ }
++ setup_irq(AR531X_MISC_IRQ_GPIO, &cascade);
++ setup_irq(AR531X_MISC_IRQ_AHB_PROC, &ar2315_ahb_proc_interrupt);
++ setup_irq(AR2315_IRQ_MISC_INTRS, &cascade);
++}
++
++const struct ar231x_gpiodev ar2315_gpiodev;
++
++static u32
++ar2315_gpio_get_output(void)
++{
++ u32 reg;
++ reg = ar231x_read_reg(AR2315_GPIO_CR);
++ reg &= ar2315_gpiodev.valid_mask;
++ return reg;
++}
++
++static u32
++ar2315_gpio_set_output(u32 mask, u32 val)
++{
++ u32 reg;
++
++ reg = ar231x_read_reg(AR2315_GPIO_CR);
++ reg &= ~mask;
++ reg |= val;
++ ar231x_write_reg(AR2315_GPIO_CR, reg);
++ return reg;
++}
++
++static u32
++ar2315_gpio_get(void)
++{
++ u32 reg;
++ reg = ar231x_read_reg(AR2315_GPIO_DI);
++ reg &= ar2315_gpiodev.valid_mask;
++ return reg;
++}
++
++static u32
++ar2315_gpio_set(u32 mask, u32 value)
++{
++ u32 reg;
++ reg = ar231x_read_reg(AR2315_GPIO_DO);
++ reg &= ~mask;
++ reg |= value;
++ ar231x_write_reg(AR2315_GPIO_DO, reg);
++ return reg;
++}
++
++const struct ar231x_gpiodev ar2315_gpiodev = {
++ .valid_mask = (1 << 22) - 1,
++ .get_output = ar2315_gpio_get_output,
++ .set_output = ar2315_gpio_set_output,
++ .get = ar2315_gpio_get,
++ .set = ar2315_gpio_set,
++};
++
++static struct ar231x_eth ar2315_eth_data = {
++ .reset_base = AR2315_RESET,
++ .reset_mac = AR2315_RESET_ENET0,
++ .reset_phy = AR2315_RESET_EPHY0,
++ .phy_base = AR2315_ENET0,
++ .config = &ar231x_board,
++};
++
++static struct resource ar2315_spiflash_res[] = {
++ {
++ .name = "flash_base",
++ .flags = IORESOURCE_MEM,
++ .start = KSEG1ADDR(AR2315_SPI_READ),
++ .end = KSEG1ADDR(AR2315_SPI_READ) + 0x1000000 - 1,
++ },
++ {
++ .name = "flash_regs",
++ .flags = IORESOURCE_MEM,
++ .start = 0x11300000,
++ .end = 0x11300012,
++ },
++};
++
++static struct platform_device ar2315_spiflash = {
++ .id = 0,
++ .name = "spiflash",
++ .resource = ar2315_spiflash_res,
++ .num_resources = ARRAY_SIZE(ar2315_spiflash_res)
++};
++
++static struct platform_device ar2315_wdt = {
++ .id = 0,
++ .name = "ar2315_wdt",
++};
++
++#define SPI_FLASH_CTL 0x00
++#define SPI_FLASH_OPCODE 0x04
++#define SPI_FLASH_DATA 0x08
++
++static inline u32
++spiflash_read_reg(int reg)
++{
++ return ar231x_read_reg(KSEG1ADDR(AR2315_SPI) + reg);
++}
++
++static inline void
++spiflash_write_reg(int reg, u32 data)
++{
++ ar231x_write_reg(KSEG1ADDR(AR2315_SPI) + reg, data);
++}
++
++static u32
++spiflash_wait_status(void)
++{
++ u32 reg;
++
++ do {
++ reg = spiflash_read_reg(SPI_FLASH_CTL);
++ } while (reg & SPI_CTL_BUSY);
++
++ return reg;
++}
++
++static u8
++spiflash_probe(void)
++{
++ u32 reg;
++
++ reg = spiflash_wait_status();
++ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++ reg |= (1 << 4) | 4 | SPI_CTL_START;
++
++ spiflash_write_reg(SPI_FLASH_OPCODE, 0xab);
++ spiflash_write_reg(SPI_FLASH_CTL, reg);
++
++ reg = spiflash_wait_status();
++ reg = spiflash_read_reg(SPI_FLASH_DATA);
++ reg &= 0xff;
++
++ return (u8) reg;
++}
++
++
++#define STM_8MBIT_SIGNATURE 0x13
++#define STM_16MBIT_SIGNATURE 0x14
++#define STM_32MBIT_SIGNATURE 0x15
++#define STM_64MBIT_SIGNATURE 0x16
++#define STM_128MBIT_SIGNATURE 0x17
++
++static u8 __init *
++ar2315_flash_limit(void)
++{
++ u32 flash_size = 0;
++
++ /* probe the flash chip size */
++ switch(spiflash_probe()) {
++ case STM_8MBIT_SIGNATURE:
++ flash_size = 0x00100000;
++ break;
++ case STM_16MBIT_SIGNATURE:
++ flash_size = 0x00200000;
++ break;
++ case STM_32MBIT_SIGNATURE:
++ flash_size = 0x00400000;
++ break;
++ case STM_64MBIT_SIGNATURE:
++ flash_size = 0x00800000;
++ break;
++ case STM_128MBIT_SIGNATURE:
++ flash_size = 0x01000000;
++ break;
++ }
++
++ ar2315_spiflash_res[0].end = ar2315_spiflash_res[0].start +
++ flash_size - 1;
++ return (u8 *) ar2315_spiflash_res[0].end + 1;
++}
++
++#ifdef CONFIG_LEDS_GPIO
++static struct gpio_led ar2315_leds[6];
++static struct gpio_led_platform_data ar2315_led_data = {
++ .leds = (void *) ar2315_leds,
++};
++
++static struct platform_device ar2315_gpio_leds = {
++ .name = "leds-gpio",
++ .id = -1,
++ .dev = {
++ .platform_data = (void *) &ar2315_led_data,
++ }
++};
++
++static void __init
++ar2315_init_gpio(void)
++{
++ static char led_names[6][6];
++ int i, led = 0;
++
++ ar2315_led_data.num_leds = 0;
++ for(i = 1; i < 8; i++)
++ {
++ if((i == AR2315_RESET_GPIO) ||
++ (i == ar231x_board.config->resetConfigGpio))
++ continue;
++
++ if(i == ar231x_board.config->sysLedGpio)
++ strcpy(led_names[led], "wlan");
++ else
++ sprintf(led_names[led], "gpio%d", i);
++
++ ar2315_leds[led].name = led_names[led];
++ ar2315_leds[led].gpio = i;
++ ar2315_leds[led].active_low = 0;
++ led++;
++ }
++ ar2315_led_data.num_leds = led;
++ platform_device_register(&ar2315_gpio_leds);
++}
++#else
++static inline void ar2315_init_gpio(void)
++{
++}
++#endif
++
++int __init
++ar2315_init_devices(void)
++{
++ if (!IS_2315())
++ return 0;
++
++ /* Find board configuration */
++ ar231x_find_config(ar2315_flash_limit());
++ ar2315_eth_data.macaddr = ar231x_board.config->enet0_mac;
++
++ ar2315_init_gpio();
++ platform_device_register(&ar2315_wdt);
++ platform_device_register(&ar2315_spiflash);
++ ar231x_add_ethernet(0, AR2315_ENET0, AR2315_IRQ_ENET0_INTRS,
++ &ar2315_eth_data);
++ ar231x_add_wmac(0, AR2315_WLAN0, AR2315_IRQ_WLAN0_INTRS);
++
++ return 0;
++}
++
++static void
++ar2315_restart(char *command)
++{
++ void (*mips_reset_vec)(void) = (void *) 0xbfc00000;
++
++ local_irq_disable();
++
++ /* try reset the system via reset control */
++ ar231x_write_reg(AR2315_COLD_RESET,AR2317_RESET_SYSTEM);
++
++ /* Cold reset does not work on the AR2315/6, use the GPIO reset bits a workaround.
++ * give it some time to attempt a gpio based hardware reset
++ * (atheros reference design workaround) */
++ gpio_direction_output(AR2315_RESET_GPIO, 0);
++ mdelay(100);
++
++ /* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
++ * workaround. Attempt to jump to the mips reset location -
++ * the boot loader itself might be able to recover the system */
++ mips_reset_vec();
++}
++
++
++/*
++ * This table is indexed by bits 5..4 of the CLOCKCTL1 register
++ * to determine the predevisor value.
++ */
++static int __initdata CLOCKCTL1_PREDIVIDE_TABLE[4] = {
++ 1,
++ 2,
++ 4,
++ 5
++};
++
++static int __initdata PLLC_DIVIDE_TABLE[5] = {
++ 2,
++ 3,
++ 4,
++ 6,
++ 3
++};
++
++static unsigned int __init
++ar2315_sys_clk(unsigned int clockCtl)
++{
++ unsigned int pllcCtrl,cpuDiv;
++ unsigned int pllcOut,refdiv,fdiv,divby2;
++ unsigned int clkDiv;
++
++ pllcCtrl = ar231x_read_reg(AR2315_PLLC_CTL);
++ refdiv = (pllcCtrl & PLLC_REF_DIV_M) >> PLLC_REF_DIV_S;
++ refdiv = CLOCKCTL1_PREDIVIDE_TABLE[refdiv];
++ fdiv = (pllcCtrl & PLLC_FDBACK_DIV_M) >> PLLC_FDBACK_DIV_S;
++ divby2 = (pllcCtrl & PLLC_ADD_FDBACK_DIV_M) >> PLLC_ADD_FDBACK_DIV_S;
++ divby2 += 1;
++ pllcOut = (40000000/refdiv)*(2*divby2)*fdiv;
++
++
++ /* clkm input selected */
++ switch(clockCtl & CPUCLK_CLK_SEL_M) {
++ case 0:
++ case 1:
++ clkDiv = PLLC_DIVIDE_TABLE[(pllcCtrl & PLLC_CLKM_DIV_M) >> PLLC_CLKM_DIV_S];
++ break;
++ case 2:
++ clkDiv = PLLC_DIVIDE_TABLE[(pllcCtrl & PLLC_CLKC_DIV_M) >> PLLC_CLKC_DIV_S];
++ break;
++ default:
++ pllcOut = 40000000;
++ clkDiv = 1;
++ break;
++ }
++ cpuDiv = (clockCtl & CPUCLK_CLK_DIV_M) >> CPUCLK_CLK_DIV_S;
++ cpuDiv = cpuDiv * 2 ?: 1;
++ return (pllcOut/(clkDiv * cpuDiv));
++}
++
++static inline unsigned int
++ar2315_cpu_frequency(void)
++{
++ return ar2315_sys_clk(ar231x_read_reg(AR2315_CPUCLK));
++}
++
++static inline unsigned int
++ar2315_apb_frequency(void)
++{
++ return ar2315_sys_clk(ar231x_read_reg(AR2315_AMBACLK));
++}
++
++void __init
++ar2315_time_init(void)
++{
++ mips_hpt_frequency = ar2315_cpu_frequency() / 2;
++}
++
++void __init
++ar2315_prom_init(void)
++{
++ u32 memsize, memcfg, devid;
++
++ if (!IS_2315())
++ return;
++
++ memcfg = ar231x_read_reg(AR2315_MEM_CFG);
++ memsize = 1 + ((memcfg & SDRAM_DATA_WIDTH_M) >> SDRAM_DATA_WIDTH_S);
++ memsize <<= 1 + ((memcfg & SDRAM_COL_WIDTH_M) >> SDRAM_COL_WIDTH_S);
++ memsize <<= 1 + ((memcfg & SDRAM_ROW_WIDTH_M) >> SDRAM_ROW_WIDTH_S);
++ memsize <<= 3;
++ add_memory_region(0, memsize, BOOT_MEM_RAM);
++
++ /* Detect the hardware based on the device ID */
++ devid = ar231x_read_reg(AR2315_SREV) & AR2315_REV_CHIP;
++ switch(devid) {
++ case 0x90:
++ case 0x91:
++ ar231x_devtype = DEV_TYPE_AR2317;
++ break;
++ default:
++ ar231x_devtype = DEV_TYPE_AR2315;
++ break;
++ }
++ ar231x_gpiodev = &ar2315_gpiodev;
++ ar231x_board.devid = devid;
++}
++
++void __init
++ar2315_plat_setup(void)
++{
++ u32 config;
++
++ if (!IS_2315())
++ return;
++
++ /* Clear any lingering AHB errors */
++ config = read_c0_config();
++ write_c0_config(config & ~0x3);
++ ar231x_write_reg(AR2315_AHB_ERR0,AHB_ERROR_DET);
++ ar231x_read_reg(AR2315_AHB_ERR1);
++ ar231x_write_reg(AR2315_WDC, AR2315_WDC_IGNORE_EXPIRATION);
++
++ _machine_restart = ar2315_restart;
++ ar231x_serial_setup(KSEG1ADDR(AR2315_UART0), ar2315_apb_frequency());
++}
+--- /dev/null
++++ b/arch/mips/ar231x/ar2315.h
+@@ -0,0 +1,37 @@
++#ifndef __AR2315_H
++#define __AR2315_H
++
++#ifdef CONFIG_ATHEROS_AR2315
++
++extern void ar2315_irq_init(void);
++extern int ar2315_init_devices(void);
++extern void ar2315_prom_init(void);
++extern void ar2315_plat_setup(void);
++extern void ar2315_time_init(void);
++
++#else
++
++static inline void ar2315_irq_init(void)
++{
++}
++
++static inline int ar2315_init_devices(void)
++{
++ return 0;
++}
++
++static inline void ar2315_prom_init(void)
++{
++}
++
++static inline void ar2315_plat_setup(void)
++{
++}
++
++static inline void ar2315_time_init(void)
++{
++}
++
++#endif
++
++#endif
+--- /dev/null
++++ b/arch/mips/ar231x/ar5312.h
+@@ -0,0 +1,38 @@
++#ifndef __AR5312_H
++#define __AR5312_H
++
++#ifdef CONFIG_ATHEROS_AR5312
++
++extern void ar5312_irq_init(void);
++extern int ar5312_init_devices(void);
++extern void ar5312_prom_init(void);
++extern void ar5312_plat_setup(void);
++extern void ar5312_time_init(void);
++extern void ar5312_time_init(void);
++
++#else
++
++static inline void ar5312_irq_init(void)
++{
++}
++
++static inline int ar5312_init_devices(void)
++{
++ return 0;
++}
++
++static inline void ar5312_prom_init(void)
++{
++}
++
++static inline void ar5312_plat_setup(void)
++{
++}
++
++static inline void ar5312_time_init(void)
++{
++}
++
++#endif
++
++#endif
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/ar231x.h
+@@ -0,0 +1,54 @@
++#ifndef __AR531X_H
++#define __AR531X_H
++
++#define AR531X_MISC_IRQ_BASE 0x20
++#define AR531X_GPIO_IRQ_BASE 0x30
++
++/* Software's idea of interrupts handled by "CPU Interrupt Controller" */
++#define AR531X_IRQ_NONE MIPS_CPU_IRQ_BASE+0
++#define AR531X_IRQ_CPU_CLOCK MIPS_CPU_IRQ_BASE+7 /* C0_CAUSE: 0x8000 */
++
++/* Miscellaneous interrupts, which share IP6 */
++#define AR531X_MISC_IRQ_NONE AR531X_MISC_IRQ_BASE+0
++#define AR531X_MISC_IRQ_TIMER AR531X_MISC_IRQ_BASE+1
++#define AR531X_MISC_IRQ_AHB_PROC AR531X_MISC_IRQ_BASE+2
++#define AR531X_MISC_IRQ_AHB_DMA AR531X_MISC_IRQ_BASE+3
++#define AR531X_MISC_IRQ_GPIO AR531X_MISC_IRQ_BASE+4
++#define AR531X_MISC_IRQ_UART0 AR531X_MISC_IRQ_BASE+5
++#define AR531X_MISC_IRQ_UART0_DMA AR531X_MISC_IRQ_BASE+6
++#define AR531X_MISC_IRQ_WATCHDOG AR531X_MISC_IRQ_BASE+7
++#define AR531X_MISC_IRQ_LOCAL AR531X_MISC_IRQ_BASE+8
++#define AR531X_MISC_IRQ_SPI AR531X_MISC_IRQ_BASE+9
++#define AR531X_MISC_IRQ_COUNT 10
++
++/* GPIO Interrupts [0..7], share AR531X_MISC_IRQ_GPIO */
++#define AR531X_GPIO_IRQ_NONE AR531X_GPIO_IRQ_BASE+0
++#define AR531X_GPIO_IRQ(n) AR531X_GPIO_IRQ_BASE+n
++#define AR531X_GPIO_IRQ_COUNT 22
++
++static inline u32
++ar231x_read_reg(u32 reg)
++{
++ return __raw_readl((u32 *) reg);
++}
++
++static inline void
++ar231x_write_reg(u32 reg, u32 val)
++{
++ __raw_writel(val, (u32 *)reg);
++}
++
++static inline u32
++ar231x_mask_reg(u32 reg, u32 mask, u32 val)
++{
++ u32 ret;
++
++ ret = ar231x_read_reg(reg);
++ ret &= ~mask;
++ ret |= val;
++ ar231x_write_reg(reg, ret);
++
++ return ret;
++}
++
++#endif
+--- /dev/null
++++ b/arch/mips/ar231x/devices.h
+@@ -0,0 +1,27 @@
++#ifndef __AR231X_DEVICES_H
++#define __AR231X_DEVICES_H
++
++enum {
++ /* handled by ar5312.c */
++ DEV_TYPE_AR2312,
++ DEV_TYPE_AR2313,
++ DEV_TYPE_AR5312,
++
++ /* handled by ar2315.c */
++ DEV_TYPE_AR2315,
++ DEV_TYPE_AR2316,
++ DEV_TYPE_AR2317,
++
++ DEV_TYPE_UNKNOWN
++};
++
++extern int ar231x_devtype;
++extern struct ar231x_board_config ar231x_board;
++extern void (*ar231x_irq_dispatch)(void);
++
++extern int ar231x_find_config(u8 *flash_limit);
++extern void ar231x_serial_setup(u32 mapbase, unsigned int uartclk);
++extern int ar231x_add_wmac(int nr, u32 base, int irq);
++extern int ar231x_add_ethernet(int nr, u32 base, int irq, void *pdata);
++
++#endif
+--- /dev/null
++++ b/arch/mips/ar231x/devices.c
+@@ -0,0 +1,174 @@
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/serial.h>
++#include <linux/serial_core.h>
++#include <linux/serial_8250.h>
++#include <linux/platform_device.h>
++#include <ar231x_platform.h>
++#include <ar231x.h>
++#include "devices.h"
++#include "ar5312.h"
++#include "ar2315.h"
++
++struct ar231x_board_config ar231x_board;
++int ar231x_devtype = DEV_TYPE_UNKNOWN;
++const struct ar231x_gpiodev *ar231x_gpiodev;
++
++static struct resource ar231x_eth0_res[] = {
++ {
++ .name = "eth0_membase",
++ .flags = IORESOURCE_MEM,
++ },
++ {
++ .name = "eth0_irq",
++ .flags = IORESOURCE_IRQ,
++ }
++};
++
++static struct resource ar231x_eth1_res[] = {
++ {
++ .name = "eth1_membase",
++ .flags = IORESOURCE_MEM,
++ },
++ {
++ .name = "eth1_irq",
++ .flags = IORESOURCE_IRQ,
++ }
++};
++
++static struct platform_device ar231x_eth[] = {
++ {
++ .id = 0,
++ .name = "ar231x-eth",
++ .resource = ar231x_eth0_res,
++ .num_resources = ARRAY_SIZE(ar231x_eth0_res)
++ },
++ {
++ .id = 1,
++ .name = "ar231x-eth",
++ .resource = ar231x_eth1_res,
++ .num_resources = ARRAY_SIZE(ar231x_eth1_res)
++ }
++};
++
++static struct resource ar231x_wmac0_res[] = {
++ {
++ .name = "wmac0_membase",
++ .flags = IORESOURCE_MEM,
++ },
++ {
++ .name = "wmac0_irq",
++ .flags = IORESOURCE_IRQ,
++ }
++};
++
++static struct resource ar231x_wmac1_res[] = {
++ {
++ .name = "wmac1_membase",
++ .flags = IORESOURCE_MEM,
++ },
++ {
++ .name = "wmac1_irq",
++ .flags = IORESOURCE_IRQ,
++ }
++};
++
++
++static struct platform_device ar231x_wmac[] = {
++ {
++ .id = 0,
++ .name = "ar231x-wmac",
++ .resource = ar231x_wmac0_res,
++ .num_resources = ARRAY_SIZE(ar231x_wmac0_res),
++ .dev.platform_data = &ar231x_board,
++ },
++ {
++ .id = 1,
++ .name = "ar231x-wmac",
++ .resource = ar231x_wmac1_res,
++ .num_resources = ARRAY_SIZE(ar231x_wmac1_res),
++ .dev.platform_data = &ar231x_board,
++ },
++};
++
++static const char *devtype_strings[] = {
++ [DEV_TYPE_AR5312] = "Atheros AR5312",
++ [DEV_TYPE_AR2312] = "Atheros AR2312",
++ [DEV_TYPE_AR2313] = "Atheros AR2313",
++ [DEV_TYPE_AR2315] = "Atheros AR2315",
++ [DEV_TYPE_AR2316] = "Atheros AR2316",
++ [DEV_TYPE_AR2317] = "Atheros AR2317",
++ [DEV_TYPE_UNKNOWN] = "Atheros (unknown)",
++};
++
++const char *get_system_type(void)
++{
++ if ((ar231x_devtype >= ARRAY_SIZE(devtype_strings)) ||
++ !devtype_strings[ar231x_devtype])
++ return devtype_strings[DEV_TYPE_UNKNOWN];
++ return devtype_strings[ar231x_devtype];
++}
++
++
++int __init
++ar231x_add_ethernet(int nr, u32 base, int irq, void *pdata)
++{
++ struct resource *res;
++
++ ar231x_eth[nr].dev.platform_data = pdata;
++ res = &ar231x_eth[nr].resource[0];
++ res->start = base;
++ res->end = base + 0x2000 - 1;
++ res++;
++ res->start = irq;
++ res->end = irq;
++ return platform_device_register(&ar231x_eth[nr]);
++}
++
++void __init
++ar231x_serial_setup(u32 mapbase, unsigned int uartclk)
++{
++ struct uart_port s;
++
++ memset(&s, 0, sizeof(s));
++
++ s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST;
++ s.iotype = UPIO_MEM;
++ s.irq = AR531X_MISC_IRQ_UART0;
++ s.regshift = 2;
++ s.mapbase = mapbase;
++ s.uartclk = uartclk;
++ s.membase = (void __iomem *)s.mapbase;
++
++ early_serial_setup(&s);
++}
++
++int __init
++ar231x_add_wmac(int nr, u32 base, int irq)
++{
++ struct resource *res;
++
++ ar231x_wmac[nr].dev.platform_data = &ar231x_board;
++ res = &ar231x_wmac[nr].resource[0];
++ res->start = base;
++ res->end = base + 0x10000 - 1;
++ res++;
++ res->start = irq;
++ res->end = irq;
++ return platform_device_register(&ar231x_wmac[nr]);
++}
++
++static int __init ar231x_register_devices(void)
++{
++ static struct resource res = {
++ .start = 0xFFFFFFFF,
++ };
++
++ platform_device_register_simple("GPIODEV", 0, &res, 1);
++ ar5312_init_devices();
++ ar2315_init_devices();
++
++ return 0;
++}
++
++device_initcall(ar231x_register_devices);
--- /dev/null
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -359,6 +359,12 @@ config AX88796_93CX6
+ help
+ Select this if your platform comes with an external 93CX6 eeprom.
+
++config AR231X_ETHERNET
++ tristate "AR231x Ethernet support"
++ depends on NET_ETHERNET && ATHEROS
++ help
++ Support for the AR231x/531x ethernet controller
++
+ config MACE
+ tristate "MACE (Power Mac ethernet) support"
+ depends on PPC_PMAC && PPC32
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -199,6 +199,7 @@ obj-$(CONFIG_EQUALIZER) += eql.o
+ obj-$(CONFIG_KORINA) += korina.o
+ obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
+ obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
++obj-$(CONFIG_AR231X_ETHERNET) += ar231x.o
+ obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
+ obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
+ obj-$(CONFIG_DECLANCE) += declance.o
+--- /dev/null
++++ b/drivers/net/ar231x.c
+@@ -0,0 +1,1267 @@
++/*
++ * ar231x.c: Linux driver for the Atheros AR231x Ethernet device.
++ *
++ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * Thanks to Atheros for providing hardware and documentation
++ * enabling me to write this driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * Additional credits:
++ * This code is taken from John Taylor's Sibyte driver and then
++ * modified for the AR2313.
++ */
++
++#include <linux/module.h>
++#include <linux/version.h>
++#include <linux/types.h>
++#include <linux/errno.h>
++#include <linux/ioport.h>
++#include <linux/pci.h>
++#include <linux/netdevice.h>
++#include <linux/etherdevice.h>
++#include <linux/skbuff.h>
++#include <linux/init.h>
++#include <linux/delay.h>
++#include <linux/mm.h>
++#include <linux/highmem.h>
++#include <linux/sockios.h>
++#include <linux/pkt_sched.h>
++#include <linux/mii.h>
++#include <linux/phy.h>
++#include <linux/ethtool.h>
++#include <linux/ctype.h>
++#include <linux/platform_device.h>
++
++#include <net/sock.h>
++#include <net/ip.h>
++
++#include <asm/system.h>
++#include <asm/io.h>
++#include <asm/irq.h>
++#include <asm/byteorder.h>
++#include <asm/uaccess.h>
++#include <asm/bootinfo.h>
++
++#define AR2313_MTU 1692
++#define AR2313_PRIOS 1
++#define AR2313_QUEUES (2*AR2313_PRIOS)
++#define AR2313_DESCR_ENTRIES 64
++
++
++#ifndef min
++#define min(a,b) (((a)<(b))?(a):(b))
++#endif
++
++#ifndef SMP_CACHE_BYTES
++#define SMP_CACHE_BYTES L1_CACHE_BYTES
++#endif
++
++#define AR2313_MBOX_SET_BIT 0x8
++
++#include "ar231x.h"
++
++/*
++ * New interrupt handler strategy:
++ *
++ * An old interrupt handler worked using the traditional method of
++ * replacing an skbuff with a new one when a packet arrives. However
++ * the rx rings do not need to contain a static number of buffer
++ * descriptors, thus it makes sense to move the memory allocation out
++ * of the main interrupt handler and do it in a bottom half handler
++ * and only allocate new buffers when the number of buffers in the
++ * ring is below a certain threshold. In order to avoid starving the
++ * NIC under heavy load it is however necessary to force allocation
++ * when hitting a minimum threshold. The strategy for alloction is as
++ * follows:
++ *
++ * RX_LOW_BUF_THRES - allocate buffers in the bottom half
++ * RX_PANIC_LOW_THRES - we are very low on buffers, allocate
++ * the buffers in the interrupt handler
++ * RX_RING_THRES - maximum number of buffers in the rx ring
++ *
++ * One advantagous side effect of this allocation approach is that the
++ * entire rx processing can be done without holding any spin lock
++ * since the rx rings and registers are totally independent of the tx
++ * ring and its registers. This of course includes the kmalloc's of
++ * new skb's. Thus start_xmit can run in parallel with rx processing
++ * and the memory allocation on SMP systems.
++ *
++ * Note that running the skb reallocation in a bottom half opens up
++ * another can of races which needs to be handled properly. In
++ * particular it can happen that the interrupt handler tries to run
++ * the reallocation while the bottom half is either running on another
++ * CPU or was interrupted on the same CPU. To get around this the
++ * driver uses bitops to prevent the reallocation routines from being
++ * reentered.
++ *
++ * TX handling can also be done without holding any spin lock, wheee
++ * this is fun! since tx_csm is only written to by the interrupt
++ * handler.
++ */
++
++/*
++ * Threshold values for RX buffer allocation - the low water marks for
++ * when to start refilling the rings are set to 75% of the ring
++ * sizes. It seems to make sense to refill the rings entirely from the
++ * intrrupt handler once it gets below the panic threshold, that way
++ * we don't risk that the refilling is moved to another CPU when the
++ * one running the interrupt handler just got the slab code hot in its
++ * cache.
++ */
++#define RX_RING_SIZE AR2313_DESCR_ENTRIES
++#define RX_PANIC_THRES (RX_RING_SIZE/4)
++#define RX_LOW_THRES ((3*RX_RING_SIZE)/4)
++#define CRC_LEN 4
++#define RX_OFFSET 2
++
++#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
++#define VLAN_HDR 4
++#else
++#define VLAN_HDR 0
++#endif
++
++#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + RX_OFFSET)
++
++#ifdef MODULE
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@openwrt.org>");
++MODULE_DESCRIPTION("AR231x Ethernet driver");
++#endif
++
++#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
++
++// prototypes
++static void ar231x_halt(struct net_device *dev);
++static void rx_tasklet_func(unsigned long data);
++static void rx_tasklet_cleanup(struct net_device *dev);
++static void ar231x_multicast_list(struct net_device *dev);
++
++static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
++static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value);
++static int ar231x_mdiobus_reset(struct mii_bus *bus);
++static int ar231x_mdiobus_probe (struct net_device *dev);
++static void ar231x_adjust_link(struct net_device *dev);
++
++#ifndef ERR
++#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
++#endif
++
++
++int __init ar231x_probe(struct platform_device *pdev)
++{
++ struct net_device *dev;
++ struct ar231x_private *sp;
++ struct resource *res;
++ unsigned long ar_eth_base;
++ char buf[64];
++
++ dev = alloc_etherdev(sizeof(struct ar231x_private));
++
++ if (dev == NULL) {
++ printk(KERN_ERR
++ "ar231x: Unable to allocate net_device structure!\n");
++ return -ENOMEM;
++ }
++
++ platform_set_drvdata(pdev, dev);
++
++ sp = netdev_priv(dev);
++ sp->dev = dev;
++ sp->cfg = pdev->dev.platform_data;
++
++ sprintf(buf, "eth%d_membase", pdev->id);
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
++ if (!res)
++ return -ENODEV;
++
++ sp->link = 0;
++ ar_eth_base = res->start;
++
++ sprintf(buf, "eth%d_irq", pdev->id);
++ dev->irq = platform_get_irq_byname(pdev, buf);
++
++ spin_lock_init(&sp->lock);
++
++ /* initialize func pointers */
++ dev->open = &ar231x_open;
++ dev->stop = &ar231x_close;
++ dev->hard_start_xmit = &ar231x_start_xmit;
++
++ dev->set_multicast_list = &ar231x_multicast_list;
++ dev->do_ioctl = &ar231x_ioctl;
++
++ // SAMEER: do we need this?
++ dev->features |= NETIF_F_HIGHDMA;
++
++ tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long) dev);
++ tasklet_disable(&sp->rx_tasklet);
++
++ sp->eth_regs =
++ ioremap_nocache(virt_to_phys(ar_eth_base), sizeof(*sp->eth_regs));
++ if (!sp->eth_regs) {
++ printk("Can't remap eth registers\n");
++ return (-ENXIO);
++ }
++
++ /*
++ * When there's only one MAC, PHY regs are typically on ENET0,
++ * even though the MAC might be on ENET1.
++ * Needto remap PHY regs separately in this case
++ */
++ if (virt_to_phys(ar_eth_base) == virt_to_phys(sp->phy_regs))
++ sp->phy_regs = sp->eth_regs;
++ else {
++ sp->phy_regs =
++ ioremap_nocache(virt_to_phys(sp->cfg->phy_base),
++ sizeof(*sp->phy_regs));
++ if (!sp->phy_regs) {
++ printk("Can't remap phy registers\n");
++ return (-ENXIO);
++ }
++ }
++
++ sp->dma_regs =
++ ioremap_nocache(virt_to_phys(ar_eth_base + 0x1000),
++ sizeof(*sp->dma_regs));
++ dev->base_addr = (unsigned int) sp->dma_regs;
++ if (!sp->dma_regs) {
++ printk("Can't remap DMA registers\n");
++ return (-ENXIO);
++ }
++
++ sp->int_regs = ioremap_nocache(virt_to_phys(sp->cfg->reset_base), 4);
++ if (!sp->int_regs) {
++ printk("Can't remap INTERRUPT registers\n");
++ return (-ENXIO);
++ }
++
++ strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
++ sp->name[sizeof(sp->name) - 1] = '\0';
++ memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
++
++ if (ar231x_init(dev)) {
++ /*
++ * ar231x_init() calls ar231x_init_cleanup() on error.
++ */
++ kfree(dev);
++ return -ENODEV;
++ }
++
++ if (register_netdev(dev)) {
++ printk("%s: register_netdev failed\n", __func__);
++ return -1;
++ }
++
++ printk("%s: %s: %02x:%02x:%02x:%02x:%02x:%02x, irq %d\n",
++ dev->name, sp->name,
++ dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
++ dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5], dev->irq);
++
++ sp->mii_bus = mdiobus_alloc();
++ if (sp->mii_bus == NULL)
++ return -1;
++
++ sp->mii_bus->priv = dev;
++ sp->mii_bus->read = ar231x_mdiobus_read;
++ sp->mii_bus->write = ar231x_mdiobus_write;
++ sp->mii_bus->reset = ar231x_mdiobus_reset;
++ sp->mii_bus->name = "ar231x_eth_mii";
++ snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "0");
++ sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
++ *sp->mii_bus->irq = PHY_POLL;
++
++ mdiobus_register(sp->mii_bus);
++
++ if (ar231x_mdiobus_probe(dev) != 0) {
++ printk(KERN_ERR "ar231x: mdiobus_probe failed");
++ rx_tasklet_cleanup(dev);
++ ar231x_init_cleanup(dev);
++ unregister_netdev(dev);
++ kfree(dev);
++ } else {
++ /* start link poll timer */
++ ar231x_setup_timer(dev);
++ }
++
++ return 0;
++}
++
++
++static void ar231x_multicast_list(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int filter;
++
++ filter = sp->eth_regs->mac_control;
++
++ if (dev->flags & IFF_PROMISC)
++ filter |= MAC_CONTROL_PR;
++ else
++ filter &= ~MAC_CONTROL_PR;
++ if ((dev->flags & IFF_ALLMULTI) || (dev->mc_count > 0))
++ filter |= MAC_CONTROL_PM;
++ else
++ filter &= ~MAC_CONTROL_PM;
++
++ sp->eth_regs->mac_control = filter;
++}
++
++static void rx_tasklet_cleanup(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ /*
++ * Tasklet may be scheduled. Need to get it removed from the list
++ * since we're about to free the struct.
++ */
++
++ sp->unloading = 1;
++ tasklet_enable(&sp->rx_tasklet);
++ tasklet_kill(&sp->rx_tasklet);
++}
++
++static int __exit ar231x_remove(struct platform_device *pdev)
++{
++ struct net_device *dev = platform_get_drvdata(pdev);
++ struct ar231x_private *sp = netdev_priv(dev);
++ rx_tasklet_cleanup(dev);
++ ar231x_init_cleanup(dev);
++ unregister_netdev(dev);
++ mdiobus_unregister(sp->mii_bus);
++ mdiobus_free(sp->mii_bus);
++ kfree(dev);
++ return 0;
++}
++
++
++/*
++ * Restart the AR2313 ethernet controller.
++ */
++static int ar231x_restart(struct net_device *dev)
++{
++ /* disable interrupts */
++ disable_irq(dev->irq);
++
++ /* stop mac */
++ ar231x_halt(dev);
++
++ /* initialize */
++ ar231x_init(dev);
++
++ /* enable interrupts */
++ enable_irq(dev->irq);
++
++ return 0;
++}
++
++static struct platform_driver ar231x_driver = {
++ .driver.name = "ar231x-eth",
++ .probe = ar231x_probe,
++ .remove = ar231x_remove,
++};
++
++int __init ar231x_module_init(void)
++{
++ return platform_driver_register(&ar231x_driver);
++}
++
++void __exit ar231x_module_cleanup(void)
++{
++ platform_driver_unregister(&ar231x_driver);
++}
++
++module_init(ar231x_module_init);
++module_exit(ar231x_module_cleanup);
++
++
++static void ar231x_free_descriptors(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ if (sp->rx_ring != NULL) {
++ kfree((void *) KSEG0ADDR(sp->rx_ring));
++ sp->rx_ring = NULL;
++ sp->tx_ring = NULL;
++ }
++}
++
++
++static int ar231x_allocate_descriptors(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ int size;
++ int j;
++ ar231x_descr_t *space;
++
++ if (sp->rx_ring != NULL) {
++ printk("%s: already done.\n", __FUNCTION__);
++ return 0;
++ }
++
++ size =
++ (sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES));
++ space = kmalloc(size, GFP_KERNEL);
++ if (space == NULL)
++ return 1;
++
++ /* invalidate caches */
++ dma_cache_inv((unsigned int) space, size);
++
++ /* now convert pointer to KSEG1 */
++ space = (ar231x_descr_t *) KSEG1ADDR(space);
++
++ memset((void *) space, 0, size);
++
++ sp->rx_ring = space;
++ space += AR2313_DESCR_ENTRIES;
++
++ sp->tx_ring = space;
++ space += AR2313_DESCR_ENTRIES;
++
++ /* Initialize the transmit Descriptors */
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ ar231x_descr_t *td = &sp->tx_ring[j];
++ td->status = 0;
++ td->devcs = DMA_TX1_CHAINED;
++ td->addr = 0;
++ td->descr =
++ virt_to_phys(&sp->
++ tx_ring[(j + 1) & (AR2313_DESCR_ENTRIES - 1)]);
++ }
++
++ return 0;
++}
++
++
++/*
++ * Generic cleanup handling data allocated during init. Used when the
++ * module is unloaded or if an error occurs during initialization
++ */
++static void ar231x_init_cleanup(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ struct sk_buff *skb;
++ int j;
++
++ ar231x_free_descriptors(dev);
++
++ if (sp->eth_regs)
++ iounmap((void *) sp->eth_regs);
++ if (sp->dma_regs)
++ iounmap((void *) sp->dma_regs);
++
++ if (sp->rx_skb) {
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ skb = sp->rx_skb[j];
++ if (skb) {
++ sp->rx_skb[j] = NULL;
++ dev_kfree_skb(skb);
++ }
++ }
++ kfree(sp->rx_skb);
++ sp->rx_skb = NULL;
++ }
++
++ if (sp->tx_skb) {
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ skb = sp->tx_skb[j];
++ if (skb) {
++ sp->tx_skb[j] = NULL;
++ dev_kfree_skb(skb);
++ }
++ }
++ kfree(sp->tx_skb);
++ sp->tx_skb = NULL;
++ }
++}
++
++static int ar231x_setup_timer(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ init_timer(&sp->link_timer);
++
++ sp->link_timer.function = ar231x_link_timer_fn;
++ sp->link_timer.data = (int) dev;
++ sp->link_timer.expires = jiffies + HZ;
++
++ add_timer(&sp->link_timer);
++ return 0;
++
++}
++
++static void ar231x_link_timer_fn(unsigned long data)
++{
++ struct net_device *dev = (struct net_device *) data;
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ // see if the link status changed
++ // This was needed to make sure we set the PHY to the
++ // autonegotiated value of half or full duplex.
++ ar231x_check_link(dev);
++
++ // Loop faster when we don't have link.
++ // This was needed to speed up the AP bootstrap time.
++ if (sp->link == 0) {
++ mod_timer(&sp->link_timer, jiffies + HZ / 2);
++ } else {
++ mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
++ }
++}
++
++static void ar231x_check_link(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ u16 phyData;
++
++ phyData = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
++ if (sp->phyData != phyData) {
++ if (phyData & BMSR_LSTATUS) {
++ /* link is present, ready link partner ability to deterine
++ duplexity */
++ int duplex = 0;
++ u16 reg;
++
++ sp->link = 1;
++ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMCR);
++ if (reg & BMCR_ANENABLE) {
++ /* auto neg enabled */
++ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_LPA);
++ duplex = (reg & (LPA_100FULL | LPA_10FULL)) ? 1 : 0;
++ } else {
++ /* no auto neg, just read duplex config */
++ duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
++ }
++
++ printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
++ dev->name, (duplex) ? "full" : "half");
++
++ if (duplex) {
++ /* full duplex */
++ sp->eth_regs->mac_control =
++ ((sp->eth_regs->
++ mac_control | MAC_CONTROL_F) & ~MAC_CONTROL_DRO);
++ } else {
++ /* half duplex */
++ sp->eth_regs->mac_control =
++ ((sp->eth_regs->
++ mac_control | MAC_CONTROL_DRO) & ~MAC_CONTROL_F);
++ }
++ } else {
++ /* no link */
++ sp->link = 0;
++ }
++ sp->phyData = phyData;
++ }
++}
++
++static int ar231x_reset_reg(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int ethsal, ethsah;
++ unsigned int flags;
++
++ *sp->int_regs |= sp->cfg->reset_mac;
++ mdelay(10);
++ *sp->int_regs &= ~sp->cfg->reset_mac;
++ mdelay(10);
++ *sp->int_regs |= sp->cfg->reset_phy;
++ mdelay(10);
++ *sp->int_regs &= ~sp->cfg->reset_phy;
++ mdelay(10);
++
++ sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
++ mdelay(10);
++ sp->dma_regs->bus_mode =
++ ((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
++
++ /* enable interrupts */
++ sp->dma_regs->intr_ena = (DMA_STATUS_AIS |
++ DMA_STATUS_NIS |
++ DMA_STATUS_RI |
++ DMA_STATUS_TI | DMA_STATUS_FBE);
++ sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
++ sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
++ sp->dma_regs->control =
++ (DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
++
++ sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
++ sp->eth_regs->vlan_tag = (0x8100);
++
++ /* Enable Ethernet Interface */
++ flags = (MAC_CONTROL_TE | /* transmit enable */
++ MAC_CONTROL_PM | /* pass mcast */
++ MAC_CONTROL_F | /* full duplex */
++ MAC_CONTROL_HBD); /* heart beat disabled */
++
++ if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
++ flags |= MAC_CONTROL_PR;
++ }
++ sp->eth_regs->mac_control = flags;
++
++ /* Set all Ethernet station address registers to their initial values */
++ ethsah = ((((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF));
++
++ ethsal = ((((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
++ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
++ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF));
++
++ sp->eth_regs->mac_addr[0] = ethsah;
++ sp->eth_regs->mac_addr[1] = ethsal;
++
++ mdelay(10);
++
++ return (0);
++}
++
++
++static int ar231x_init(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ int ecode = 0;
++
++ /*
++ * Allocate descriptors
++ */
++ if (ar231x_allocate_descriptors(dev)) {
++ printk("%s: %s: ar231x_allocate_descriptors failed\n",
++ dev->name, __FUNCTION__);
++ ecode = -EAGAIN;
++ goto init_error;
++ }
++
++ /*
++ * Get the memory for the skb rings.
++ */
++ if (sp->rx_skb == NULL) {
++ sp->rx_skb =
++ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
++ GFP_KERNEL);
++ if (!(sp->rx_skb)) {
++ printk("%s: %s: rx_skb kmalloc failed\n",
++ dev->name, __FUNCTION__);
++ ecode = -EAGAIN;
++ goto init_error;
++ }
++ }
++ memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
++
++ if (sp->tx_skb == NULL) {
++ sp->tx_skb =
++ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
++ GFP_KERNEL);
++ if (!(sp->tx_skb)) {
++ printk("%s: %s: tx_skb kmalloc failed\n",
++ dev->name, __FUNCTION__);
++ ecode = -EAGAIN;
++ goto init_error;
++ }
++ }
++ memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
++
++ /*
++ * Set tx_csm before we start receiving interrupts, otherwise
++ * the interrupt handler might think it is supposed to process
++ * tx ints before we are up and running, which may cause a null
++ * pointer access in the int handler.
++ */
++ sp->rx_skbprd = 0;
++ sp->cur_rx = 0;
++ sp->tx_prd = 0;
++ sp->tx_csm = 0;
++
++ /*
++ * Zero the stats before starting the interface
++ */
++ memset(&dev->stats, 0, sizeof(dev->stats));
++
++ /*
++ * We load the ring here as there seem to be no way to tell the
++ * firmware to wipe the ring without re-initializing it.
++ */
++ ar231x_load_rx_ring(dev, RX_RING_SIZE);
++
++ /*
++ * Init hardware
++ */
++ ar231x_reset_reg(dev);
++
++ /*
++ * Get the IRQ
++ */
++ ecode =
++ request_irq(dev->irq, &ar231x_interrupt,
++ IRQF_SHARED | IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
++ dev->name, dev);
++ if (ecode) {
++ printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
++ dev->name, __FUNCTION__, dev->irq);
++ goto init_error;
++ }
++
++
++ tasklet_enable(&sp->rx_tasklet);
++
++ return 0;
++
++ init_error:
++ ar231x_init_cleanup(dev);
++ return ecode;
++}
++
++/*
++ * Load the rx ring.
++ *
++ * Loading rings is safe without holding the spin lock since this is
++ * done only before the device is enabled, thus no interrupts are
++ * generated and by the interrupt handler/tasklet handler.
++ */
++static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs)
++{
++
++ struct ar231x_private *sp = netdev_priv(dev);
++ short i, idx;
++
++ idx = sp->rx_skbprd;
++
++ for (i = 0; i < nr_bufs; i++) {
++ struct sk_buff *skb;
++ ar231x_descr_t *rd;
++
++ if (sp->rx_skb[idx])
++ break;
++
++ // partha: create additional room for the second GRE fragment
++ skb = alloc_skb(AR2313_BUFSIZE + 128, GFP_ATOMIC);
++ if (!skb) {
++ printk("\n\n\n\n %s: No memory in system\n\n\n\n",
++ __FUNCTION__);
++ break;
++ }
++ // partha: create additional room in the front for tx pkt capture
++ skb_reserve(skb, 32);
++
++ /*
++ * Make sure IP header starts on a fresh cache line.
++ */
++ skb->dev = dev;
++ skb_reserve(skb, RX_OFFSET);
++ sp->rx_skb[idx] = skb;
++
++ rd = (ar231x_descr_t *) & sp->rx_ring[idx];
++
++ /* initialize dma descriptor */
++ rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
++ DMA_RX1_CHAINED);
++ rd->addr = virt_to_phys(skb->data);
++ rd->descr =
++ virt_to_phys(&sp->
++ rx_ring[(idx + 1) & (AR2313_DESCR_ENTRIES - 1)]);
++ rd->status = DMA_RX_OWN;
++
++ idx = DSC_NEXT(idx);
++ }
++
++ if (i)
++ sp->rx_skbprd = idx;
++
++ return;
++}
++
++#define AR2313_MAX_PKTS_PER_CALL 64
++
++static int ar231x_rx_int(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ struct sk_buff *skb, *skb_new;
++ ar231x_descr_t *rxdesc;
++ unsigned int status;
++ u32 idx;
++ int pkts = 0;
++ int rval;
++
++ idx = sp->cur_rx;
++
++ /* process at most the entire ring and then wait for another interrupt
++ */
++ while (1) {
++
++ rxdesc = &sp->rx_ring[idx];
++ status = rxdesc->status;
++ if (status & DMA_RX_OWN) {
++ /* SiByte owns descriptor or descr not yet filled in */
++ rval = 0;
++ break;
++ }
++
++ if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
++ rval = 1;
++ break;
++ }
++
++ if ((status & (DMA_RX_ERROR | DMA_RX_ERR_LENGTH)) &&
++ (!(status & DMA_RX_LONG))) {
++ dev->stats.rx_errors++;
++ dev->stats.rx_dropped++;
++
++ /* add statistics counters */
++ if (status & DMA_RX_ERR_CRC)
++ dev->stats.rx_crc_errors++;
++ if (status & DMA_RX_ERR_COL)
++ dev->stats.rx_over_errors++;
++ if (status & DMA_RX_ERR_LENGTH)
++ dev->stats.rx_length_errors++;
++ if (status & DMA_RX_ERR_RUNT)
++ dev->stats.rx_over_errors++;
++ if (status & DMA_RX_ERR_DESC)
++ dev->stats.rx_over_errors++;
++
++ } else {
++ /* alloc new buffer. */
++ skb_new = dev_alloc_skb(AR2313_BUFSIZE + RX_OFFSET + 128);
++ if (skb_new != NULL) {
++
++ skb = sp->rx_skb[idx];
++ /* set skb */
++ skb_put(skb,
++ ((status >> DMA_RX_LEN_SHIFT) & 0x3fff) - CRC_LEN);
++
++ dev->stats.rx_bytes += skb->len;
++ skb->protocol = eth_type_trans(skb, dev);
++ /* pass the packet to upper layers */
++ netif_rx(skb);
++
++ skb_new->dev = dev;
++ /* 16 bit align */
++ skb_reserve(skb_new, RX_OFFSET + 32);
++ /* reset descriptor's curr_addr */
++ rxdesc->addr = virt_to_phys(skb_new->data);
++
++ dev->stats.rx_packets++;
++ sp->rx_skb[idx] = skb_new;
++ } else {
++ dev->stats.rx_dropped++;
++ }
++ }
++
++ rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
++ DMA_RX1_CHAINED);
++ rxdesc->status = DMA_RX_OWN;
++
++ idx = DSC_NEXT(idx);
++ }
++
++ sp->cur_rx = idx;
++
++ return rval;
++}
++
++
++static void ar231x_tx_int(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ u32 idx;
++ struct sk_buff *skb;
++ ar231x_descr_t *txdesc;
++ unsigned int status = 0;
++
++ idx = sp->tx_csm;
++
++ while (idx != sp->tx_prd) {
++ txdesc = &sp->tx_ring[idx];
++
++ if ((status = txdesc->status) & DMA_TX_OWN) {
++ /* ar231x dma still owns descr */
++ break;
++ }
++ /* done with this descriptor */
++ dma_unmap_single(NULL, txdesc->addr,
++ txdesc->devcs & DMA_TX1_BSIZE_MASK,
++ DMA_TO_DEVICE);
++ txdesc->status = 0;
++
++ if (status & DMA_TX_ERROR) {
++ dev->stats.tx_errors++;
++ dev->stats.tx_dropped++;
++ if (status & DMA_TX_ERR_UNDER)
++ dev->stats.tx_fifo_errors++;
++ if (status & DMA_TX_ERR_HB)
++ dev->stats.tx_heartbeat_errors++;
++ if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
++ dev->stats.tx_carrier_errors++;
++ if (status & (DMA_TX_ERR_LATE |
++ DMA_TX_ERR_COL |
++ DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
++ dev->stats.tx_aborted_errors++;
++ } else {
++ /* transmit OK */
++ dev->stats.tx_packets++;
++ }
++
++ skb = sp->tx_skb[idx];
++ sp->tx_skb[idx] = NULL;
++ idx = DSC_NEXT(idx);
++ dev->stats.tx_bytes += skb->len;
++ dev_kfree_skb_irq(skb);
++ }
++
++ sp->tx_csm = idx;
++
++ return;
++}
++
++
++static void rx_tasklet_func(unsigned long data)
++{
++ struct net_device *dev = (struct net_device *) data;
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ if (sp->unloading) {
++ return;
++ }
++
++ if (ar231x_rx_int(dev)) {
++ tasklet_hi_schedule(&sp->rx_tasklet);
++ } else {
++ unsigned long flags;
++ spin_lock_irqsave(&sp->lock, flags);
++ sp->dma_regs->intr_ena |= DMA_STATUS_RI;
++ spin_unlock_irqrestore(&sp->lock, flags);
++ }
++}
++
++static void rx_schedule(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
++
++ tasklet_hi_schedule(&sp->rx_tasklet);
++}
++
++static irqreturn_t ar231x_interrupt(int irq, void *dev_id)
++{
++ struct net_device *dev = (struct net_device *) dev_id;
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int status, enabled;
++
++ /* clear interrupt */
++ /*
++ * Don't clear RI bit if currently disabled.
++ */
++ status = sp->dma_regs->status;
++ enabled = sp->dma_regs->intr_ena;
++ sp->dma_regs->status = status & enabled;
++
++ if (status & DMA_STATUS_NIS) {
++ /* normal status */
++ /*
++ * Don't schedule rx processing if interrupt
++ * is already disabled.
++ */
++ if (status & enabled & DMA_STATUS_RI) {
++ /* receive interrupt */
++ rx_schedule(dev);
++ }
++ if (status & DMA_STATUS_TI) {
++ /* transmit interrupt */
++ ar231x_tx_int(dev);
++ }
++ }
++
++ /* abnormal status */
++ if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS)) {
++ ar231x_restart(dev);
++ }
++ return IRQ_HANDLED;
++}
++
++
++static int ar231x_open(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int ethsal, ethsah;
++
++ /* reset the hardware, in case the MAC address changed */
++ ethsah = ((((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF));
++
++ ethsal = ((((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
++ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
++ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF));
++
++ sp->eth_regs->mac_addr[0] = ethsah;
++ sp->eth_regs->mac_addr[1] = ethsal;
++
++ mdelay(10);
++
++ dev->mtu = 1500;
++ netif_start_queue(dev);
++
++ sp->eth_regs->mac_control |= MAC_CONTROL_RE;
++
++ return 0;
++}
++
++static void ar231x_halt(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ int j;
++
++ tasklet_disable(&sp->rx_tasklet);
++
++ /* kill the MAC */
++ sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE | /* disable Receives */
++ MAC_CONTROL_TE); /* disable Transmits */
++ /* stop dma */
++ sp->dma_regs->control = 0;
++ sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
++
++ /* place phy and MAC in reset */
++ *sp->int_regs |= (sp->cfg->reset_mac | sp->cfg->reset_phy);
++
++ /* free buffers on tx ring */
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ struct sk_buff *skb;
++ ar231x_descr_t *txdesc;
++
++ txdesc = &sp->tx_ring[j];
++ txdesc->descr = 0;
++
++ skb = sp->tx_skb[j];
++ if (skb) {
++ dev_kfree_skb(skb);
++ sp->tx_skb[j] = NULL;
++ }
++ }
++}
++
++/*
++ * close should do nothing. Here's why. It's called when
++ * 'ifconfig bond0 down' is run. If it calls free_irq then
++ * the irq is gone forever ! When bond0 is made 'up' again,
++ * the ar231x_open () does not call request_irq (). Worse,
++ * the call to ar231x_halt() generates a WDOG reset due to
++ * the write to 'sp->int_regs' and the box reboots.
++ * Commenting this out is good since it allows the
++ * system to resume when bond0 is made up again.
++ */
++static int ar231x_close(struct net_device *dev)
++{
++#if 0
++ /*
++ * Disable interrupts
++ */
++ disable_irq(dev->irq);
++
++ /*
++ * Without (or before) releasing irq and stopping hardware, this
++ * is an absolute non-sense, by the way. It will be reset instantly
++ * by the first irq.
++ */
++ netif_stop_queue(dev);
++
++ /* stop the MAC and DMA engines */
++ ar231x_halt(dev);
++
++ /* release the interrupt */
++ free_irq(dev->irq, dev);
++
++#endif
++ return 0;
++}
++
++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ ar231x_descr_t *td;
++ u32 idx;
++
++ idx = sp->tx_prd;
++ td = &sp->tx_ring[idx];
++
++ if (td->status & DMA_TX_OWN) {
++ /* free skbuf and lie to the caller that we sent it out */
++ dev->stats.tx_dropped++;
++ dev_kfree_skb(skb);
++
++ /* restart transmitter in case locked */
++ sp->dma_regs->xmt_poll = 0;
++ return 0;
++ }
++
++ /* Setup the transmit descriptor. */
++ td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
++ (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
++ td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
++ td->status = DMA_TX_OWN;
++
++ /* kick transmitter last */
++ sp->dma_regs->xmt_poll = 0;
++
++ sp->tx_skb[idx] = skb;
++ idx = DSC_NEXT(idx);
++ sp->tx_prd = idx;
++
++ return 0;
++}
++
++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
++{
++ struct mii_ioctl_data *data = (struct mii_ioctl_data *) &ifr->ifr_data;
++ struct ar231x_private *sp = netdev_priv(dev);
++ int ret;
++
++ switch (cmd) {
++
++ case SIOCETHTOOL:
++ spin_lock_irq(&sp->lock);
++ ret = phy_ethtool_ioctl(sp->phy_dev, (void *) ifr->ifr_data);
++ spin_unlock_irq(&sp->lock);
++ return ret;
++
++ case SIOCSIFHWADDR:
++ if (copy_from_user
++ (dev->dev_addr, ifr->ifr_data, sizeof(dev->dev_addr)))
++ return -EFAULT;
++ return 0;
++
++ case SIOCGIFHWADDR:
++ if (copy_to_user
++ (ifr->ifr_data, dev->dev_addr, sizeof(dev->dev_addr)))
++ return -EFAULT;
++ return 0;
++
++ case SIOCGMIIPHY:
++ case SIOCGMIIREG:
++ case SIOCSMIIREG:
++ return phy_mii_ioctl(sp->phy_dev, data, cmd);
++
++ default:
++ break;
++ }
++
++ return -EOPNOTSUPP;
++}
++
++static void ar231x_adjust_link(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int mc;
++
++ if (!sp->phy_dev->link)
++ return;
++
++ if (sp->phy_dev->duplex != sp->oldduplex) {
++ mc = readl(&sp->eth_regs->mac_control);
++ mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
++ if (sp->phy_dev->duplex)
++ mc |= MAC_CONTROL_F;
++ else
++ mc |= MAC_CONTROL_DRO;
++ writel(mc, &sp->eth_regs->mac_control);
++ sp->oldduplex = sp->phy_dev->duplex;
++ }
++}
++
++#define MII_ADDR(phy, reg) \
++ ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
++
++static int
++ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
++{
++ struct net_device *const dev = bus->priv;
++ struct ar231x_private *sp = netdev_priv(dev);
++ volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
++
++ ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
++ while (ethernet->mii_addr & MII_ADDR_BUSY);
++ return (ethernet->mii_data >> MII_DATA_SHIFT);
++}
++
++static int
++ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
++ u16 value)
++{
++ struct net_device *const dev = bus->priv;
++ struct ar231x_private *sp = netdev_priv(dev);
++ volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
++
++ while (ethernet->mii_addr & MII_ADDR_BUSY);
++ ethernet->mii_data = value << MII_DATA_SHIFT;
++ ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
++
++ return 0;
++}
++
++static int ar231x_mdiobus_reset(struct mii_bus *bus)
++{
++ struct net_device *const dev = bus->priv;
++
++ ar231x_reset_reg(dev);
++
++ return 0;
++}
++
++static int ar231x_mdiobus_probe (struct net_device *dev)
++{
++ struct ar231x_private *const sp = netdev_priv(dev);
++ struct phy_device *phydev = NULL;
++ int phy_addr;
++
++ /* find the first (lowest address) PHY on the current MAC's MII bus */
++ for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
++ if (sp->mii_bus->phy_map[phy_addr]) {
++ phydev = sp->mii_bus->phy_map[phy_addr];
++ sp->phy = phy_addr;
++ break; /* break out with first one found */
++ }
++
++ if (!phydev) {
++ printk (KERN_ERR "ar231x: %s: no PHY found\n", dev->name);
++ return -1;
++ }
++
++ /* now we are supposed to have a proper phydev, to attach to... */
++ BUG_ON(!phydev);
++ BUG_ON(phydev->attached_dev);
++
++ phydev = phy_connect(dev, phydev->dev.bus_id, &ar231x_adjust_link, 0,
++ PHY_INTERFACE_MODE_MII);
++
++ if (IS_ERR(phydev)) {
++ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
++ return PTR_ERR(phydev);
++ }
++
++ /* mask with MAC supported features */
++ phydev->supported &= (SUPPORTED_10baseT_Half
++ | SUPPORTED_10baseT_Full
++ | SUPPORTED_100baseT_Half
++ | SUPPORTED_100baseT_Full
++ | SUPPORTED_Autoneg
++ /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
++ | SUPPORTED_MII
++ | SUPPORTED_TP);
++
++ phydev->advertising = phydev->supported;
++
++ sp->oldduplex = -1;
++ sp->phy_dev = phydev;
++
++ printk(KERN_INFO "%s: attached PHY driver [%s] "
++ "(mii_bus:phy_addr=%s)\n",
++ dev->name, phydev->drv->name, phydev->dev.bus_id);
++
++ return 0;
++}
++
+--- /dev/null
++++ b/drivers/net/ar231x.h
+@@ -0,0 +1,302 @@
++/*
++ * ar231x.h: Linux driver for the Atheros AR231x Ethernet device.
++ *
++ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * Thanks to Atheros for providing hardware and documentation
++ * enabling me to write this driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ */
++
++#ifndef _AR2313_H_
++#define _AR2313_H_
++
++#include <linux/autoconf.h>
++#include <linux/bitops.h>
++#include <asm/bootinfo.h>
++#include <ar231x_platform.h>
++
++/*
++ * probe link timer - 5 secs
++ */
++#define LINK_TIMER (5*HZ)
++
++#define IS_DMA_TX_INT(X) (((X) & (DMA_STATUS_TI)) != 0)
++#define IS_DMA_RX_INT(X) (((X) & (DMA_STATUS_RI)) != 0)
++#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN)) == 0)
++
++#define AR2313_TX_TIMEOUT (HZ/4)
++
++/*
++ * Rings
++ */
++#define DSC_RING_ENTRIES_SIZE (AR2313_DESCR_ENTRIES * sizeof(struct desc))
++#define DSC_NEXT(idx) ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
++
++#define AR2313_MBGET 2
++#define AR2313_MBSET 3
++#define AR2313_PCI_RECONFIG 4
++#define AR2313_PCI_DUMP 5
++#define AR2313_TEST_PANIC 6
++#define AR2313_TEST_NULLPTR 7
++#define AR2313_READ_DATA 8
++#define AR2313_WRITE_DATA 9
++#define AR2313_GET_VERSION 10
++#define AR2313_TEST_HANG 11
++#define AR2313_SYNC 12
++
++#define DMA_RX_ERR_CRC BIT(1)
++#define DMA_RX_ERR_DRIB BIT(2)
++#define DMA_RX_ERR_MII BIT(3)
++#define DMA_RX_EV2 BIT(5)
++#define DMA_RX_ERR_COL BIT(6)
++#define DMA_RX_LONG BIT(7)
++#define DMA_RX_LS BIT(8) /* last descriptor */
++#define DMA_RX_FS BIT(9) /* first descriptor */
++#define DMA_RX_MF BIT(10) /* multicast frame */
++#define DMA_RX_ERR_RUNT BIT(11) /* runt frame */
++#define DMA_RX_ERR_LENGTH BIT(12) /* length error */
++#define DMA_RX_ERR_DESC BIT(14) /* descriptor error */
++#define DMA_RX_ERROR BIT(15) /* error summary */
++#define DMA_RX_LEN_MASK 0x3fff0000
++#define DMA_RX_LEN_SHIFT 16
++#define DMA_RX_FILT BIT(30)
++#define DMA_RX_OWN BIT(31) /* desc owned by DMA controller */
++
++#define DMA_RX1_BSIZE_MASK 0x000007ff
++#define DMA_RX1_BSIZE_SHIFT 0
++#define DMA_RX1_CHAINED BIT(24)
++#define DMA_RX1_RER BIT(25)
++
++#define DMA_TX_ERR_UNDER BIT(1) /* underflow error */
++#define DMA_TX_ERR_DEFER BIT(2) /* excessive deferral */
++#define DMA_TX_COL_MASK 0x78
++#define DMA_TX_COL_SHIFT 3
++#define DMA_TX_ERR_HB BIT(7) /* hearbeat failure */
++#define DMA_TX_ERR_COL BIT(8) /* excessive collisions */
++#define DMA_TX_ERR_LATE BIT(9) /* late collision */
++#define DMA_TX_ERR_LINK BIT(10) /* no carrier */
++#define DMA_TX_ERR_LOSS BIT(11) /* loss of carrier */
++#define DMA_TX_ERR_JABBER BIT(14) /* transmit jabber timeout */
++#define DMA_TX_ERROR BIT(15) /* frame aborted */
++#define DMA_TX_OWN BIT(31) /* descr owned by DMA controller */
++
++#define DMA_TX1_BSIZE_MASK 0x000007ff
++#define DMA_TX1_BSIZE_SHIFT 0
++#define DMA_TX1_CHAINED BIT(24) /* chained descriptors */
++#define DMA_TX1_TER BIT(25) /* transmit end of ring */
++#define DMA_TX1_FS BIT(29) /* first segment */
++#define DMA_TX1_LS BIT(30) /* last segment */
++#define DMA_TX1_IC BIT(31) /* interrupt on completion */
++
++#define RCVPKT_LENGTH(X) (X >> 16) /* Received pkt Length */
++
++#define MAC_CONTROL_RE BIT(2) /* receive enable */
++#define MAC_CONTROL_TE BIT(3) /* transmit enable */
++#define MAC_CONTROL_DC BIT(5) /* Deferral check */
++#define MAC_CONTROL_ASTP BIT(8) /* Auto pad strip */
++#define MAC_CONTROL_DRTY BIT(10) /* Disable retry */
++#define MAC_CONTROL_DBF BIT(11) /* Disable bcast frames */
++#define MAC_CONTROL_LCC BIT(12) /* late collision ctrl */
++#define MAC_CONTROL_HP BIT(13) /* Hash Perfect filtering */
++#define MAC_CONTROL_HASH BIT(14) /* Unicast hash filtering */
++#define MAC_CONTROL_HO BIT(15) /* Hash only filtering */
++#define MAC_CONTROL_PB BIT(16) /* Pass Bad frames */
++#define MAC_CONTROL_IF BIT(17) /* Inverse filtering */
++#define MAC_CONTROL_PR BIT(18) /* promiscuous mode (valid frames only) */
++#define MAC_CONTROL_PM BIT(19) /* pass multicast */
++#define MAC_CONTROL_F BIT(20) /* full-duplex */
++#define MAC_CONTROL_DRO BIT(23) /* Disable Receive Own */
++#define MAC_CONTROL_HBD BIT(28) /* heart-beat disabled (MUST BE SET) */
++#define MAC_CONTROL_BLE BIT(30) /* big endian mode */
++#define MAC_CONTROL_RA BIT(31) /* receive all (valid and invalid frames) */
++
++#define MII_ADDR_BUSY BIT(0)
++#define MII_ADDR_WRITE BIT(1)
++#define MII_ADDR_REG_SHIFT 6
++#define MII_ADDR_PHY_SHIFT 11
++#define MII_DATA_SHIFT 0
++
++#define FLOW_CONTROL_FCE BIT(1)
++
++#define DMA_BUS_MODE_SWR BIT(0) /* software reset */
++#define DMA_BUS_MODE_BLE BIT(7) /* big endian mode */
++#define DMA_BUS_MODE_PBL_SHIFT 8 /* programmable burst length 32 */
++#define DMA_BUS_MODE_DBO BIT(20) /* big-endian descriptors */
++
++#define DMA_STATUS_TI BIT(0) /* transmit interrupt */
++#define DMA_STATUS_TPS BIT(1) /* transmit process stopped */
++#define DMA_STATUS_TU BIT(2) /* transmit buffer unavailable */
++#define DMA_STATUS_TJT BIT(3) /* transmit buffer timeout */
++#define DMA_STATUS_UNF BIT(5) /* transmit underflow */
++#define DMA_STATUS_RI BIT(6) /* receive interrupt */
++#define DMA_STATUS_RU BIT(7) /* receive buffer unavailable */
++#define DMA_STATUS_RPS BIT(8) /* receive process stopped */
++#define DMA_STATUS_ETI BIT(10) /* early transmit interrupt */
++#define DMA_STATUS_FBE BIT(13) /* fatal bus interrupt */
++#define DMA_STATUS_ERI BIT(14) /* early receive interrupt */
++#define DMA_STATUS_AIS BIT(15) /* abnormal interrupt summary */
++#define DMA_STATUS_NIS BIT(16) /* normal interrupt summary */
++#define DMA_STATUS_RS_SHIFT 17 /* receive process state */
++#define DMA_STATUS_TS_SHIFT 20 /* transmit process state */
++#define DMA_STATUS_EB_SHIFT 23 /* error bits */
++
++#define DMA_CONTROL_SR BIT(1) /* start receive */
++#define DMA_CONTROL_ST BIT(13) /* start transmit */
++#define DMA_CONTROL_SF BIT(21) /* store and forward */
++
++
++typedef struct {
++ volatile unsigned int status; // OWN, Device control and status.
++ volatile unsigned int devcs; // pkt Control bits + Length
++ volatile unsigned int addr; // Current Address.
++ volatile unsigned int descr; // Next descriptor in chain.
++} ar231x_descr_t;
++
++
++
++//
++// New Combo structure for Both Eth0 AND eth1
++//
++typedef struct {
++ volatile unsigned int mac_control; /* 0x00 */
++ volatile unsigned int mac_addr[2]; /* 0x04 - 0x08 */
++ volatile unsigned int mcast_table[2]; /* 0x0c - 0x10 */
++ volatile unsigned int mii_addr; /* 0x14 */
++ volatile unsigned int mii_data; /* 0x18 */
++ volatile unsigned int flow_control; /* 0x1c */
++ volatile unsigned int vlan_tag; /* 0x20 */
++ volatile unsigned int pad[7]; /* 0x24 - 0x3c */
++ volatile unsigned int ucast_table[8]; /* 0x40-0x5c */
++
++} ETHERNET_STRUCT;
++
++/********************************************************************
++ * Interrupt controller
++ ********************************************************************/
++
++typedef struct {
++ volatile unsigned int wdog_control; /* 0x08 */
++ volatile unsigned int wdog_timer; /* 0x0c */
++ volatile unsigned int misc_status; /* 0x10 */
++ volatile unsigned int misc_mask; /* 0x14 */
++ volatile unsigned int global_status; /* 0x18 */
++ volatile unsigned int reserved; /* 0x1c */
++ volatile unsigned int reset_control; /* 0x20 */
++} INTERRUPT;
++
++/********************************************************************
++ * DMA controller
++ ********************************************************************/
++typedef struct {
++ volatile unsigned int bus_mode; /* 0x00 (CSR0) */
++ volatile unsigned int xmt_poll; /* 0x04 (CSR1) */
++ volatile unsigned int rcv_poll; /* 0x08 (CSR2) */
++ volatile unsigned int rcv_base; /* 0x0c (CSR3) */
++ volatile unsigned int xmt_base; /* 0x10 (CSR4) */
++ volatile unsigned int status; /* 0x14 (CSR5) */
++ volatile unsigned int control; /* 0x18 (CSR6) */
++ volatile unsigned int intr_ena; /* 0x1c (CSR7) */
++ volatile unsigned int rcv_missed; /* 0x20 (CSR8) */
++ volatile unsigned int reserved[11]; /* 0x24-0x4c (CSR9-19) */
++ volatile unsigned int cur_tx_buf_addr; /* 0x50 (CSR20) */
++ volatile unsigned int cur_rx_buf_addr; /* 0x50 (CSR21) */
++} DMA;
++
++/*
++ * Struct private for the Sibyte.
++ *
++ * Elements are grouped so variables used by the tx handling goes
++ * together, and will go into the same cache lines etc. in order to
++ * avoid cache line contention between the rx and tx handling on SMP.
++ *
++ * Frequently accessed variables are put at the beginning of the
++ * struct to help the compiler generate better/shorter code.
++ */
++struct ar231x_private {
++ struct net_device *dev;
++ int version;
++ u32 mb[2];
++
++ volatile ETHERNET_STRUCT *phy_regs;
++ volatile ETHERNET_STRUCT *eth_regs;
++ volatile DMA *dma_regs;
++ volatile u32 *int_regs;
++ struct ar231x_eth *cfg;
++
++ spinlock_t lock; /* Serialise access to device */
++
++ /*
++ * RX and TX descriptors, must be adjacent
++ */
++ ar231x_descr_t *rx_ring;
++ ar231x_descr_t *tx_ring;
++
++
++ struct sk_buff **rx_skb;
++ struct sk_buff **tx_skb;
++
++ /*
++ * RX elements
++ */
++ u32 rx_skbprd;
++ u32 cur_rx;
++
++ /*
++ * TX elements
++ */
++ u32 tx_prd;
++ u32 tx_csm;
++
++ /*
++ * Misc elements
++ */
++ char name[48];
++ struct {
++ u32 address;
++ u32 length;
++ char *mapping;
++ } desc;
++
++
++ struct timer_list link_timer;
++ unsigned short phy; /* merlot phy = 1, samsung phy = 0x1f */
++ unsigned short mac;
++ unsigned short link; /* 0 - link down, 1 - link up */
++ u16 phyData;
++
++ struct tasklet_struct rx_tasklet;
++ int unloading;
++
++ struct phy_device *phy_dev;
++ struct mii_bus *mii_bus;
++ int oldduplex;
++};
++
++
++/*
++ * Prototypes
++ */
++static int ar231x_init(struct net_device *dev);
++#ifdef TX_TIMEOUT
++static void ar231x_tx_timeout(struct net_device *dev);
++#endif
++static int ar231x_restart(struct net_device *dev);
++static void ar231x_load_rx_ring(struct net_device *dev, int bufs);
++static irqreturn_t ar231x_interrupt(int irq, void *dev_id);
++static int ar231x_open(struct net_device *dev);
++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev);
++static int ar231x_close(struct net_device *dev);
++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr,
++ int cmd);
++static void ar231x_init_cleanup(struct net_device *dev);
++static int ar231x_setup_timer(struct net_device *dev);
++static void ar231x_link_timer_fn(unsigned long data);
++static void ar231x_check_link(struct net_device *dev);
++#endif /* _AR2313_H_ */
+++ /dev/null
---- a/drivers/mtd/devices/Kconfig
-+++ b/drivers/mtd/devices/Kconfig
-@@ -104,6 +104,10 @@ config M25PXX_USE_FAST_READ
- help
- This option enables FAST_READ access supported by ST M25Pxx.
-
-+config MTD_SPIFLASH
-+ tristate "Atheros AR2315/6/7 SPI Flash support"
-+ depends on ATHEROS_AR5315
-+
- config MTD_SLRAM
- tristate "Uncached system RAM"
- help
---- a/drivers/mtd/devices/Makefile
-+++ b/drivers/mtd/devices/Makefile
-@@ -16,3 +16,4 @@ obj-$(CONFIG_MTD_LART) += lart.o
- obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o
- obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o
- obj-$(CONFIG_MTD_M25P80) += m25p80.o
-+obj-$(CONFIG_MTD_SPIFLASH) += spiflash.o
--- /dev/null
+--- a/drivers/mtd/devices/Kconfig
++++ b/drivers/mtd/devices/Kconfig
+@@ -104,6 +104,10 @@ config M25PXX_USE_FAST_READ
+ help
+ This option enables FAST_READ access supported by ST M25Pxx.
+
++config MTD_AR2315
++ tristate "Atheros AR2315+ SPI Flash support"
++ depends on ATHEROS_AR2315
++
+ config MTD_SLRAM
+ tristate "Uncached system RAM"
+ help
+--- a/drivers/mtd/devices/Makefile
++++ b/drivers/mtd/devices/Makefile
+@@ -16,3 +16,4 @@ obj-$(CONFIG_MTD_LART) += lart.o
+ obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o
+ obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o
+ obj-$(CONFIG_MTD_M25P80) += m25p80.o
++obj-$(CONFIG_MTD_AR2315) += ar2315.o
+--- /dev/null
++++ b/drivers/mtd/devices/ar2315.c
+@@ -0,0 +1,519 @@
++
++/*
++ * MTD driver for the SPI Flash Memory support on Atheros AR2315
++ *
++ * Copyright (c) 2005-2006 Atheros Communications Inc.
++ * Copyright (C) 2006-2007 FON Technology, SL.
++ * Copyright (C) 2006-2007 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * This code is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/types.h>
++#include <linux/version.h>
++#include <linux/errno.h>
++#include <linux/slab.h>
++#include <linux/mtd/mtd.h>
++#include <linux/mtd/partitions.h>
++#include <linux/platform_device.h>
++#include <linux/sched.h>
++#include <linux/squashfs_fs.h>
++#include <linux/root_dev.h>
++#include <linux/delay.h>
++#include <asm/delay.h>
++#include <asm/io.h>
++
++#include <ar2315_spiflash.h>
++#include <ar231x_platform.h>
++#include <ar231x.h>
++
++
++#define SPIFLASH "spiflash: "
++#define busy_wait(_priv, _condition, _wait) do { \
++ while (_condition) { \
++ spin_unlock_bh(&_priv->lock); \
++ if (_wait > 1) \
++ msleep(_wait); \
++ else if ((_wait == 1) && need_resched()) \
++ schedule(); \
++ else \
++ udelay(1); \
++ spin_lock_bh(&_priv->lock); \
++ } \
++} while (0)
++
++enum {
++ FLASH_NONE,
++ FLASH_1MB,
++ FLASH_2MB,
++ FLASH_4MB,
++ FLASH_8MB,
++ FLASH_16MB,
++};
++
++/* Flash configuration table */
++struct flashconfig {
++ u32 byte_cnt;
++ u32 sector_cnt;
++ u32 sector_size;
++};
++
++const struct flashconfig flashconfig_tbl[] = {
++ [FLASH_NONE] = { 0, 0, 0},
++ [FLASH_1MB] = { STM_1MB_BYTE_COUNT, STM_1MB_SECTOR_COUNT, STM_1MB_SECTOR_SIZE},
++ [FLASH_2MB] = { STM_2MB_BYTE_COUNT, STM_2MB_SECTOR_COUNT, STM_2MB_SECTOR_SIZE},
++ [FLASH_4MB] = { STM_4MB_BYTE_COUNT, STM_4MB_SECTOR_COUNT, STM_4MB_SECTOR_SIZE},
++ [FLASH_8MB] = { STM_8MB_BYTE_COUNT, STM_8MB_SECTOR_COUNT, STM_8MB_SECTOR_SIZE},
++ [FLASH_16MB] = { STM_16MB_BYTE_COUNT, STM_16MB_SECTOR_COUNT, STM_16MB_SECTOR_SIZE}
++};
++
++/* Mapping of generic opcodes to STM serial flash opcodes */
++enum {
++ SPI_WRITE_ENABLE,
++ SPI_WRITE_DISABLE,
++ SPI_RD_STATUS,
++ SPI_WR_STATUS,
++ SPI_RD_DATA,
++ SPI_FAST_RD_DATA,
++ SPI_PAGE_PROGRAM,
++ SPI_SECTOR_ERASE,
++ SPI_BULK_ERASE,
++ SPI_DEEP_PWRDOWN,
++ SPI_RD_SIG,
++};
++
++struct opcodes {
++ __u16 code;
++ __s8 tx_cnt;
++ __s8 rx_cnt;
++};
++const struct opcodes stm_opcodes[] = {
++ [SPI_WRITE_ENABLE] = {STM_OP_WR_ENABLE, 1, 0},
++ [SPI_WRITE_DISABLE] = {STM_OP_WR_DISABLE, 1, 0},
++ [SPI_RD_STATUS] = {STM_OP_RD_STATUS, 1, 1},
++ [SPI_WR_STATUS] = {STM_OP_WR_STATUS, 1, 0},
++ [SPI_RD_DATA] = {STM_OP_RD_DATA, 4, 4},
++ [SPI_FAST_RD_DATA] = {STM_OP_FAST_RD_DATA, 5, 0},
++ [SPI_PAGE_PROGRAM] = {STM_OP_PAGE_PGRM, 8, 0},
++ [SPI_SECTOR_ERASE] = {STM_OP_SECTOR_ERASE, 4, 0},
++ [SPI_BULK_ERASE] = {STM_OP_BULK_ERASE, 1, 0},
++ [SPI_DEEP_PWRDOWN] = {STM_OP_DEEP_PWRDOWN, 1, 0},
++ [SPI_RD_SIG] = {STM_OP_RD_SIG, 4, 1},
++};
++
++/* Driver private data structure */
++struct spiflash_priv {
++ struct mtd_info mtd;
++ void *readaddr; /* memory mapped data for read */
++ void *mmraddr; /* memory mapped register space */
++ wait_queue_head_t wq;
++ spinlock_t lock;
++ int state;
++};
++
++#define to_spiflash(_mtd) container_of(_mtd, struct spiflash_priv, mtd)
++
++enum {
++ FL_READY,
++ FL_READING,
++ FL_ERASING,
++ FL_WRITING
++};
++
++/***************************************************************************************************/
++
++static u32
++spiflash_read_reg(struct spiflash_priv *priv, int reg)
++{
++ return ar231x_read_reg((u32) priv->mmraddr + reg);
++}
++
++static void
++spiflash_write_reg(struct spiflash_priv *priv, int reg, u32 data)
++{
++ ar231x_write_reg((u32) priv->mmraddr + reg, data);
++}
++
++static u32
++spiflash_wait_busy(struct spiflash_priv *priv)
++{
++ u32 reg;
++
++ busy_wait(priv, (reg = spiflash_read_reg(priv, SPI_FLASH_CTL)) &
++ SPI_CTL_BUSY, 0);
++ return reg;
++}
++
++static u32
++spiflash_sendcmd (struct spiflash_priv *priv, int opcode, u32 addr)
++{
++ const struct opcodes *op;
++ u32 reg, mask;
++
++ op = &stm_opcodes[opcode];
++ reg = spiflash_wait_busy(priv);
++ spiflash_write_reg(priv, SPI_FLASH_OPCODE,
++ ((u32) op->code) | (addr << 8));
++
++ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++ reg |= SPI_CTL_START | op->tx_cnt | (op->rx_cnt << 4);
++
++ spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
++ spiflash_wait_busy(priv);
++
++ if (!op->rx_cnt)
++ return 0;
++
++ reg = spiflash_read_reg(priv, SPI_FLASH_DATA);
++
++ switch (op->rx_cnt) {
++ case 1:
++ mask = 0x000000ff;
++ break;
++ case 2:
++ mask = 0x0000ffff;
++ break;
++ case 3:
++ mask = 0x00ffffff;
++ break;
++ default:
++ mask = 0xffffffff;
++ break;
++ }
++ reg &= mask;
++
++ return reg;
++}
++
++
++/*
++ * Probe SPI flash device
++ * Function returns 0 for failure.
++ * and flashconfig_tbl array index for success.
++ */
++static int
++spiflash_probe_chip (struct spiflash_priv *priv)
++{
++ u32 sig;
++ int flash_size;
++
++ /* Read the signature on the flash device */
++ spin_lock_bh(&priv->lock);
++ sig = spiflash_sendcmd(priv, SPI_RD_SIG, 0);
++ spin_unlock_bh(&priv->lock);
++
++ switch (sig) {
++ case STM_8MBIT_SIGNATURE:
++ flash_size = FLASH_1MB;
++ break;
++ case STM_16MBIT_SIGNATURE:
++ flash_size = FLASH_2MB;
++ break;
++ case STM_32MBIT_SIGNATURE:
++ flash_size = FLASH_4MB;
++ break;
++ case STM_64MBIT_SIGNATURE:
++ flash_size = FLASH_8MB;
++ break;
++ case STM_128MBIT_SIGNATURE:
++ flash_size = FLASH_16MB;
++ break;
++ default:
++ printk (KERN_WARNING SPIFLASH "Read of flash device signature failed!\n");
++ return 0;
++ }
++
++ return flash_size;
++}
++
++
++/* wait until the flash chip is ready and grab a lock */
++static int spiflash_wait_ready(struct spiflash_priv *priv, int state)
++{
++ DECLARE_WAITQUEUE(wait, current);
++
++retry:
++ spin_lock_bh(&priv->lock);
++ if (priv->state != FL_READY) {
++ set_current_state(TASK_UNINTERRUPTIBLE);
++ add_wait_queue(&priv->wq, &wait);
++ spin_unlock_bh(&priv->lock);
++ schedule();
++ remove_wait_queue(&priv->wq, &wait);
++
++ if(signal_pending(current))
++ return 0;
++
++ goto retry;
++ }
++ priv->state = state;
++
++ return 1;
++}
++
++static inline void spiflash_done(struct spiflash_priv *priv)
++{
++ priv->state = FL_READY;
++ spin_unlock_bh(&priv->lock);
++ wake_up(&priv->wq);
++}
++
++static void
++spiflash_wait_complete(struct spiflash_priv *priv)
++{
++ busy_wait(priv, spiflash_sendcmd(priv, SPI_RD_STATUS, 0) &
++ SPI_STATUS_WIP, 20);
++ spiflash_done(priv);
++}
++
++
++
++static int
++spiflash_erase (struct mtd_info *mtd, struct erase_info *instr)
++{
++ struct spiflash_priv *priv = to_spiflash(mtd);
++ const struct opcodes *op;
++ u32 temp, reg;
++
++ if (instr->addr + instr->len > mtd->size)
++ return -EINVAL;
++
++ if (!spiflash_wait_ready(priv, FL_ERASING))
++ return -EINTR;
++
++ spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
++ reg = spiflash_wait_busy(priv);
++
++ op = &stm_opcodes[SPI_SECTOR_ERASE];
++ temp = ((u32)instr->addr << 8) | (u32)(op->code);
++ spiflash_write_reg(priv, SPI_FLASH_OPCODE, temp);
++
++ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++ reg |= op->tx_cnt | SPI_CTL_START;
++ spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
++
++ spiflash_wait_complete(priv);
++
++ instr->state = MTD_ERASE_DONE;
++ if (instr->callback)
++ instr->callback(instr);
++
++ return 0;
++}
++
++static int
++spiflash_read (struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, u_char *buf)
++{
++ struct spiflash_priv *priv = to_spiflash(mtd);
++ u8 *read_addr;
++
++ if (!len)
++ return 0;
++
++ if (from + len > mtd->size)
++ return -EINVAL;
++
++ *retlen = len;
++
++ if (!spiflash_wait_ready(priv, FL_READING))
++ return -EINTR;
++
++ read_addr = (u8 *)(priv->readaddr + from);
++ memcpy_fromio(buf, read_addr, len);
++ spiflash_done(priv);
++
++ return 0;
++}
++
++static int
++spiflash_write (struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, const u8 *buf)
++{
++ struct spiflash_priv *priv = to_spiflash(mtd);
++ u32 opcode, bytes_left;
++
++ *retlen = 0;
++
++ if (!len)
++ return 0;
++
++ if (to + len > mtd->size)
++ return -EINVAL;
++
++ bytes_left = len;
++
++ do {
++ u32 read_len, reg, page_offset, spi_data = 0;
++
++ read_len = min(bytes_left, sizeof(u32));
++
++ /* 32-bit writes cannot span across a page boundary
++ * (256 bytes). This types of writes require two page
++ * program operations to handle it correctly. The STM part
++ * will write the overflow data to the beginning of the
++ * current page as opposed to the subsequent page.
++ */
++ page_offset = (to & (STM_PAGE_SIZE - 1)) + read_len;
++
++ if (page_offset > STM_PAGE_SIZE)
++ read_len -= (page_offset - STM_PAGE_SIZE);
++
++ if (!spiflash_wait_ready(priv, FL_WRITING))
++ return -EINTR;
++
++ spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
++ spi_data = 0;
++ switch (read_len) {
++ case 4:
++ spi_data |= buf[3] << 24;
++ /* fall through */
++ case 3:
++ spi_data |= buf[2] << 16;
++ /* fall through */
++ case 2:
++ spi_data |= buf[1] << 8;
++ /* fall through */
++ case 1:
++ spi_data |= buf[0] & 0xff;
++ break;
++ default:
++ break;
++ }
++
++ spiflash_write_reg(priv, SPI_FLASH_DATA, spi_data);
++ opcode = stm_opcodes[SPI_PAGE_PROGRAM].code |
++ (to & 0x00ffffff) << 8;
++ spiflash_write_reg(priv, SPI_FLASH_OPCODE, opcode);
++
++ reg = spiflash_read_reg(priv, SPI_FLASH_CTL);
++ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
++ reg |= (read_len + 4) | SPI_CTL_START;
++ spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
++
++ spiflash_wait_complete(priv);
++
++ bytes_left -= read_len;
++ to += read_len;
++ buf += read_len;
++
++ *retlen += read_len;
++ } while (bytes_left != 0);
++
++ return 0;
++}
++
++
++#ifdef CONFIG_MTD_PARTITIONS
++static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", "MyLoader", NULL };
++#endif
++
++
++static int
++spiflash_probe(struct platform_device *pdev)
++{
++ struct spiflash_priv *priv;
++ struct mtd_partition *parts;
++ struct mtd_info *mtd;
++ int index, num_parts;
++ int result = 0;
++
++ priv = kzalloc(sizeof(struct spiflash_priv), GFP_KERNEL);
++ spin_lock_init(&priv->lock);
++ init_waitqueue_head(&priv->wq);
++ priv->state = FL_READY;
++ mtd = &priv->mtd;
++
++ priv->mmraddr = ioremap_nocache(SPI_FLASH_MMR, SPI_FLASH_MMR_SIZE);
++ if (!priv->mmraddr) {
++ printk(KERN_WARNING SPIFLASH "Failed to map flash device\n");
++ goto error;
++ }
++
++ index = spiflash_probe_chip(priv);
++ if (!index) {
++ printk (KERN_WARNING SPIFLASH "Found no serial flash device\n");
++ goto error;
++ }
++
++ priv->readaddr = ioremap_nocache(SPI_FLASH_READ, flashconfig_tbl[index].byte_cnt);
++ if (!priv->readaddr) {
++ printk (KERN_WARNING SPIFLASH "Failed to map flash device\n");
++ goto error;
++ }
++
++ platform_set_drvdata(pdev, priv);
++ mtd->name = "spiflash";
++ mtd->type = MTD_NORFLASH;
++ mtd->flags = (MTD_CAP_NORFLASH|MTD_WRITEABLE);
++ mtd->size = flashconfig_tbl[index].byte_cnt;
++ mtd->erasesize = flashconfig_tbl[index].sector_size;
++ mtd->writesize = 1;
++ mtd->numeraseregions = 0;
++ mtd->eraseregions = NULL;
++ mtd->erase = spiflash_erase;
++ mtd->read = spiflash_read;
++ mtd->write = spiflash_write;
++ mtd->owner = THIS_MODULE;
++
++#ifdef CONFIG_MTD_PARTITIONS
++ /* parse redboot partitions */
++ num_parts = parse_mtd_partitions(mtd, part_probe_types, &parts, 0);
++ if (!num_parts)
++ goto error;
++
++ result = add_mtd_partitions(mtd, parts, num_parts);
++#endif
++
++ return result;
++
++error:
++ if (priv->mmraddr)
++ iounmap(priv->mmraddr);
++ kfree(priv);
++ return -ENXIO;
++}
++
++static int
++spiflash_remove (struct platform_device *pdev)
++{
++ struct spiflash_priv *priv = platform_get_drvdata(pdev);
++ struct mtd_info *mtd = &priv->mtd;
++
++ del_mtd_partitions(mtd);
++ iounmap(priv->mmraddr);
++ iounmap(priv->readaddr);
++ kfree(priv);
++
++ return 0;
++}
++
++struct platform_driver spiflash_driver = {
++ .driver.name = "spiflash",
++ .probe = spiflash_probe,
++ .remove = spiflash_remove,
++};
++
++int __init
++spiflash_init (void)
++{
++ return platform_driver_register(&spiflash_driver);
++}
++
++void __exit
++spiflash_exit (void)
++{
++ return platform_driver_unregister(&spiflash_driver);
++}
++
++module_init (spiflash_init);
++module_exit (spiflash_exit);
++
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("OpenWrt.org, Atheros Communications Inc");
++MODULE_DESCRIPTION("MTD driver for SPI Flash on Atheros SOC");
++
+--- /dev/null
++++ b/arch/mips/include/asm/mach-ar231x/ar2315_spiflash.h
+@@ -0,0 +1,116 @@
++/*
++ * SPI Flash Memory support header file.
++ *
++ * Copyright (c) 2005, Atheros Communications Inc.
++ * Copyright (C) 2006 FON Technology, SL.
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * This code is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 as
++ * published by the Free Software Foundation.
++ *
++ */
++#ifndef __AR2315_SPIFLASH_H
++#define __AR2315_SPIFLASH_H
++
++#define STM_PAGE_SIZE 256
++
++#define SFI_WRITE_BUFFER_SIZE 4
++#define SFI_FLASH_ADDR_MASK 0x00ffffff
++
++#define STM_8MBIT_SIGNATURE 0x13
++#define STM_M25P80_BYTE_COUNT 1048576
++#define STM_M25P80_SECTOR_COUNT 16
++#define STM_M25P80_SECTOR_SIZE 0x10000
++
++#define STM_16MBIT_SIGNATURE 0x14
++#define STM_M25P16_BYTE_COUNT 2097152
++#define STM_M25P16_SECTOR_COUNT 32
++#define STM_M25P16_SECTOR_SIZE 0x10000
++
++#define STM_32MBIT_SIGNATURE 0x15
++#define STM_M25P32_BYTE_COUNT 4194304
++#define STM_M25P32_SECTOR_COUNT 64
++#define STM_M25P32_SECTOR_SIZE 0x10000
++
++#define STM_64MBIT_SIGNATURE 0x16
++#define STM_M25P64_BYTE_COUNT 8388608
++#define STM_M25P64_SECTOR_COUNT 128
++#define STM_M25P64_SECTOR_SIZE 0x10000
++
++#define STM_128MBIT_SIGNATURE 0x17
++#define STM_M25P128_BYTE_COUNT 16777216
++#define STM_M25P128_SECTOR_COUNT 256
++#define STM_M25P128_SECTOR_SIZE 0x10000
++
++#define STM_1MB_BYTE_COUNT STM_M25P80_BYTE_COUNT
++#define STM_1MB_SECTOR_COUNT STM_M25P80_SECTOR_COUNT
++#define STM_1MB_SECTOR_SIZE STM_M25P80_SECTOR_SIZE
++#define STM_2MB_BYTE_COUNT STM_M25P16_BYTE_COUNT
++#define STM_2MB_SECTOR_COUNT STM_M25P16_SECTOR_COUNT
++#define STM_2MB_SECTOR_SIZE STM_M25P16_SECTOR_SIZE
++#define STM_4MB_BYTE_COUNT STM_M25P32_BYTE_COUNT
++#define STM_4MB_SECTOR_COUNT STM_M25P32_SECTOR_COUNT
++#define STM_4MB_SECTOR_SIZE STM_M25P32_SECTOR_SIZE
++#define STM_8MB_BYTE_COUNT STM_M25P64_BYTE_COUNT
++#define STM_8MB_SECTOR_COUNT STM_M25P64_SECTOR_COUNT
++#define STM_8MB_SECTOR_SIZE STM_M25P64_SECTOR_SIZE
++#define STM_16MB_BYTE_COUNT STM_M25P128_BYTE_COUNT
++#define STM_16MB_SECTOR_COUNT STM_M25P128_SECTOR_COUNT
++#define STM_16MB_SECTOR_SIZE STM_M25P128_SECTOR_SIZE
++
++/*
++ * ST Microelectronics Opcodes for Serial Flash
++ */
++
++#define STM_OP_WR_ENABLE 0x06 /* Write Enable */
++#define STM_OP_WR_DISABLE 0x04 /* Write Disable */
++#define STM_OP_RD_STATUS 0x05 /* Read Status */
++#define STM_OP_WR_STATUS 0x01 /* Write Status */
++#define STM_OP_RD_DATA 0x03 /* Read Data */
++#define STM_OP_FAST_RD_DATA 0x0b /* Fast Read Data */
++#define STM_OP_PAGE_PGRM 0x02 /* Page Program */
++#define STM_OP_SECTOR_ERASE 0xd8 /* Sector Erase */
++#define STM_OP_BULK_ERASE 0xc7 /* Bulk Erase */
++#define STM_OP_DEEP_PWRDOWN 0xb9 /* Deep Power-Down Mode */
++#define STM_OP_RD_SIG 0xab /* Read Electronic Signature */
++
++#define STM_STATUS_WIP 0x01 /* Write-In-Progress */
++#define STM_STATUS_WEL 0x02 /* Write Enable Latch */
++#define STM_STATUS_BP0 0x04 /* Block Protect 0 */
++#define STM_STATUS_BP1 0x08 /* Block Protect 1 */
++#define STM_STATUS_BP2 0x10 /* Block Protect 2 */
++#define STM_STATUS_SRWD 0x80 /* Status Register Write Disable */
++
++/*
++ * SPI Flash Interface Registers
++ */
++#define AR531XPLUS_SPI_READ 0x08000000
++#define AR531XPLUS_SPI_MMR 0x11300000
++#define AR531XPLUS_SPI_MMR_SIZE 12
++
++#define AR531XPLUS_SPI_CTL 0x00
++#define AR531XPLUS_SPI_OPCODE 0x04
++#define AR531XPLUS_SPI_DATA 0x08
++
++#define SPI_FLASH_READ AR531XPLUS_SPI_READ
++#define SPI_FLASH_MMR AR531XPLUS_SPI_MMR
++#define SPI_FLASH_MMR_SIZE AR531XPLUS_SPI_MMR_SIZE
++#define SPI_FLASH_CTL AR531XPLUS_SPI_CTL
++#define SPI_FLASH_OPCODE AR531XPLUS_SPI_OPCODE
++#define SPI_FLASH_DATA AR531XPLUS_SPI_DATA
++
++#define SPI_CTL_START 0x00000100
++#define SPI_CTL_BUSY 0x00010000
++#define SPI_CTL_TXCNT_MASK 0x0000000f
++#define SPI_CTL_RXCNT_MASK 0x000000f0
++#define SPI_CTL_TX_RX_CNT_MASK 0x000000ff
++#define SPI_CTL_SIZE_MASK 0x00060000
++
++#define SPI_CTL_CLK_SEL_MASK 0x03000000
++#define SPI_OPCODE_MASK 0x000000ff
++
++#define SPI_STATUS_WIP STM_STATUS_WIP
++
++#endif
+++ /dev/null
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -747,6 +747,12 @@ config TXX9_WDT
- help
- Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
-
-+config ATHEROS_WDT
-+ tristate "Atheros wisoc Watchdog Timer"
-+ depends on ATHEROS
-+ help
-+ Hardware driver for the Atheros wisoc Watchdog Timer.
-+
- # PARISC Architecture
-
- # POWERPC Architecture
---- a/drivers/watchdog/Makefile
-+++ b/drivers/watchdog/Makefile
-@@ -106,6 +106,7 @@ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
- obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
- obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
- obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
-+obj-$(CONFIG_ATHEROS_WDT) += ar2315-wtd.o
-
- # PARISC Architecture
-
+++ /dev/null
---- a/drivers/net/Kconfig
-+++ b/drivers/net/Kconfig
-@@ -359,6 +359,12 @@ config AX88796_93CX6
- help
- Select this if your platform comes with an external 93CX6 eeprom.
-
-+config AR2313
-+ tristate "AR2313 Ethernet support"
-+ depends on NET_ETHERNET && ATHEROS
-+ help
-+ Support for the AR231x/531x ethernet controller
-+
- config MACE
- tristate "MACE (Power Mac ethernet) support"
- depends on PPC_PMAC && PPC32
---- a/drivers/net/Makefile
-+++ b/drivers/net/Makefile
-@@ -199,6 +199,7 @@ obj-$(CONFIG_EQUALIZER) += eql.o
- obj-$(CONFIG_KORINA) += korina.o
- obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
- obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
-+obj-$(CONFIG_AR2313) += ar2313/
- obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
- obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
- obj-$(CONFIG_DECLANCE) += declance.o
--- /dev/null
+--- /dev/null
++++ b/drivers/watchdog/ar2315-wtd.c
+@@ -0,0 +1,200 @@
++/*
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
++ *
++ * Copyright (C) 2008 John Crispin <blogic@openwrt.org>
++ * Based on EP93xx and ifxmips wdt driver
++ */
++
++#include <linux/interrupt.h>
++#include <linux/module.h>
++#include <linux/moduleparam.h>
++#include <linux/types.h>
++#include <linux/miscdevice.h>
++#include <linux/watchdog.h>
++#include <linux/fs.h>
++#include <linux/ioport.h>
++#include <linux/notifier.h>
++#include <linux/reboot.h>
++#include <linux/init.h>
++#include <linux/platform_device.h>
++
++#include <asm/io.h>
++#include <asm/uaccess.h>
++#include <asm/system.h>
++#include <asm/addrspace.h>
++#include <ar231x_platform.h>
++#include <ar2315_regs.h>
++#include <ar231x.h>
++
++#define CLOCK_RATE 40000000
++#define HEARTBEAT(x) (x < 1 || x > 90)?(20):(x)
++
++static int wdt_timeout = 20;
++static int started = 0;
++static int in_use = 0;
++
++static void
++ar2315_wdt_enable(void)
++{
++ ar231x_write_reg(AR2315_WD, wdt_timeout * CLOCK_RATE);
++ ar231x_write_reg(AR2315_ISR, 0x80);
++}
++
++static ssize_t
++ar2315_wdt_write(struct file *file, const char __user *data, size_t len, loff_t *ppos)
++{
++ if(len)
++ ar2315_wdt_enable();
++ return len;
++}
++
++static int
++ar2315_wdt_open(struct inode *inode, struct file *file)
++{
++ if(in_use)
++ return -EBUSY;
++ ar2315_wdt_enable();
++ in_use = started = 1;
++ return nonseekable_open(inode, file);
++}
++
++static int
++ar2315_wdt_release(struct inode *inode, struct file *file)
++{
++ in_use = 0;
++ return 0;
++}
++
++static irqreturn_t
++ar2315_wdt_interrupt(int irq, void *dev_id)
++{
++ if(started)
++ {
++ printk(KERN_CRIT "watchdog expired, rebooting system\n");
++ emergency_restart();
++ } else {
++ ar231x_write_reg(AR2315_WDC, 0);
++ ar231x_write_reg(AR2315_WD, 0);
++ ar231x_write_reg(AR2315_ISR, 0x80);
++ }
++ return IRQ_HANDLED;
++}
++
++static struct watchdog_info ident = {
++ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
++ .identity = "ar2315 Watchdog",
++};
++
++static int
++ar2315_wdt_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
++{
++ int new_wdt_timeout;
++ int ret = -ENOIOCTLCMD;
++
++ switch(cmd)
++ {
++ case WDIOC_GETSUPPORT:
++ ret = copy_to_user((struct watchdog_info __user *)arg, &ident, sizeof(ident)) ? -EFAULT : 0;
++ break;
++
++ case WDIOC_KEEPALIVE:
++ ar2315_wdt_enable();
++ ret = 0;
++ break;
++
++ case WDIOC_SETTIMEOUT:
++ if((ret = get_user(new_wdt_timeout, (int __user *)arg)))
++ break;
++ wdt_timeout = HEARTBEAT(new_wdt_timeout);
++ ar2315_wdt_enable();
++ break;
++
++ case WDIOC_GETTIMEOUT:
++ ret = put_user(wdt_timeout, (int __user *)arg);
++ break;
++ }
++ return ret;
++}
++
++static struct file_operations ar2315_wdt_fops = {
++ .owner = THIS_MODULE,
++ .llseek = no_llseek,
++ .write = ar2315_wdt_write,
++ .ioctl = ar2315_wdt_ioctl,
++ .open = ar2315_wdt_open,
++ .release = ar2315_wdt_release,
++};
++
++static struct miscdevice ar2315_wdt_miscdev = {
++ .minor = WATCHDOG_MINOR,
++ .name = "watchdog",
++ .fops = &ar2315_wdt_fops,
++};
++
++static int
++ar2315_wdt_probe(struct platform_device *dev)
++{
++ int ret = 0;
++
++ ar2315_wdt_enable();
++ ret = request_irq(AR531X_MISC_IRQ_WATCHDOG, ar2315_wdt_interrupt, IRQF_DISABLED, "ar2315_wdt", NULL);
++ if(ret)
++ {
++ printk(KERN_ERR "ar2315wdt: failed to register inetrrupt\n");
++ goto out;
++ }
++
++ ret = misc_register(&ar2315_wdt_miscdev);
++ if(ret)
++ printk(KERN_ERR "ar2315wdt: failed to register miscdev\n");
++
++out:
++ return ret;
++}
++
++static int
++ar2315_wdt_remove(struct platform_device *dev)
++{
++ misc_deregister(&ar2315_wdt_miscdev);
++ free_irq(AR531X_MISC_IRQ_WATCHDOG, NULL);
++ return 0;
++}
++
++static struct platform_driver ar2315_wdt_driver = {
++ .probe = ar2315_wdt_probe,
++ .remove = ar2315_wdt_remove,
++ .driver = {
++ .name = "ar2315_wdt",
++ .owner = THIS_MODULE,
++ },
++};
++
++static int __init
++init_ar2315_wdt(void)
++{
++ int ret = platform_driver_register(&ar2315_wdt_driver);
++ if(ret)
++ printk(KERN_INFO "ar2315_wdt: error registering platfom driver!");
++ return ret;
++}
++
++static void __exit
++exit_ar2315_wdt(void)
++{
++ platform_driver_unregister(&ar2315_wdt_driver);
++}
++
++module_init(init_ar2315_wdt);
++module_exit(exit_ar2315_wdt);
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -747,6 +747,12 @@ config TXX9_WDT
+ help
+ Hardware driver for the built-in watchdog timer on TXx9 MIPS SoCs.
+
++config ATHEROS_WDT
++ tristate "Atheros wisoc Watchdog Timer"
++ depends on ATHEROS
++ help
++ Hardware driver for the Atheros wisoc Watchdog Timer.
++
+ # PARISC Architecture
+
+ # POWERPC Architecture
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -106,6 +106,7 @@ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
+ obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
+ obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
+ obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
++obj-$(CONFIG_ATHEROS_WDT) += ar2315-wtd.o
+
+ # PARISC Architecture
+
+++ /dev/null
---- a/drivers/net/ar2313/ar2313.c
-+++ b/drivers/net/ar2313/ar2313.c
-@@ -291,7 +291,7 @@ int __init ar2313_probe(struct platform_
- sp->mii_bus.write = mdiobus_write;
- sp->mii_bus.reset = mdiobus_reset;
- sp->mii_bus.name = "ar2313_eth_mii";
-- sp->mii_bus.id = 0;
-+ snprintf(sp->mii_bus.id, MII_BUS_ID_SIZE, "0");
- sp->mii_bus.irq = kmalloc(sizeof(int), GFP_KERNEL);
- *sp->mii_bus.irq = PHY_POLL;
-
+++ /dev/null
-This patch reflects changes in mdiobus implementation in kernel 2.6.28.
---- a/drivers/net/ar2313/ar2313.c
-+++ b/drivers/net/ar2313/ar2313.c
-@@ -159,10 +159,10 @@ static void rx_tasklet_func(unsigned lon
- static void rx_tasklet_cleanup(struct net_device *dev);
- static void ar2313_multicast_list(struct net_device *dev);
-
--static int mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
--static int mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value);
--static int mdiobus_reset(struct mii_bus *bus);
--static int mdiobus_probe (struct net_device *dev);
-+static int ar2313_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
-+static int ar2313_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value);
-+static int ar2313_mdiobus_reset(struct mii_bus *bus);
-+static int ar2313_mdiobus_probe (struct net_device *dev);
- static void ar2313_adjust_link(struct net_device *dev);
-
- #ifndef ERR
-@@ -286,18 +286,22 @@ int __init ar2313_probe(struct platform_
- dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
- dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5], dev->irq);
-
-- sp->mii_bus.priv = dev;
-- sp->mii_bus.read = mdiobus_read;
-- sp->mii_bus.write = mdiobus_write;
-- sp->mii_bus.reset = mdiobus_reset;
-- sp->mii_bus.name = "ar2313_eth_mii";
-- snprintf(sp->mii_bus.id, MII_BUS_ID_SIZE, "0");
-- sp->mii_bus.irq = kmalloc(sizeof(int), GFP_KERNEL);
-- *sp->mii_bus.irq = PHY_POLL;
-+ sp->mii_bus = mdiobus_alloc();
-+ if (sp->mii_bus == NULL)
-+ return -1;
-+
-+ sp->mii_bus->priv = dev;
-+ sp->mii_bus->read = ar2313_mdiobus_read;
-+ sp->mii_bus->write = ar2313_mdiobus_write;
-+ sp->mii_bus->reset = ar2313_mdiobus_reset;
-+ sp->mii_bus->name = "ar2313_eth_mii";
-+ snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "0");
-+ sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
-+ *sp->mii_bus->irq = PHY_POLL;
-
-- mdiobus_register(&sp->mii_bus);
-+ mdiobus_register(sp->mii_bus);
-
-- if (mdiobus_probe(dev) != 0) {
-+ if (ar2313_mdiobus_probe(dev) != 0) {
- printk(KERN_ERR "ar2313: mdiobus_probe failed");
- rx_tasklet_cleanup(dev);
- ar2313_init_cleanup(dev);
-@@ -432,9 +436,12 @@ static void rx_tasklet_cleanup(struct ne
- static int __exit ar2313_remove(struct platform_device *pdev)
- {
- struct net_device *dev = platform_get_drvdata(pdev);
-+ struct ar2313_private *sp = netdev_priv(dev);
- rx_tasklet_cleanup(dev);
- ar2313_init_cleanup(dev);
- unregister_netdev(dev);
-+ mdiobus_unregister(sp->mii_bus);
-+ mdiobus_free(sp->mii_bus);
- kfree(dev);
- return 0;
- }
-@@ -619,7 +626,7 @@ static void ar2313_check_link(struct net
- struct ar2313_private *sp = netdev_priv(dev);
- u16 phyData;
-
-- phyData = mdiobus_read(&sp->mii_bus, sp->phy, MII_BMSR);
-+ phyData = ar2313_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
- if (sp->phyData != phyData) {
- if (phyData & BMSR_LSTATUS) {
- /* link is present, ready link partner ability to deterine
-@@ -628,10 +635,10 @@ static void ar2313_check_link(struct net
- u16 reg;
-
- sp->link = 1;
-- reg = mdiobus_read(&sp->mii_bus, sp->phy, MII_BMCR);
-+ reg = ar2313_mdiobus_read(sp->mii_bus, sp->phy, MII_BMCR);
- if (reg & BMCR_ANENABLE) {
- /* auto neg enabled */
-- reg = mdiobus_read(&sp->mii_bus, sp->phy, MII_LPA);
-+ reg = ar2313_mdiobus_read(sp->mii_bus, sp->phy, MII_LPA);
- duplex = (reg & (LPA_100FULL | LPA_10FULL)) ? 1 : 0;
- } else {
- /* no auto neg, just read duplex config */
-@@ -1320,7 +1327,7 @@ static void ar2313_adjust_link(struct ne
- ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
-
- static int
--mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
-+ar2313_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
- {
- struct net_device *const dev = bus->priv;
- struct ar2313_private *sp = netdev_priv(dev);
-@@ -1332,7 +1339,7 @@ mdiobus_read(struct mii_bus *bus, int ph
- }
-
- static int
--mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
-+ar2313_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
- u16 value)
- {
- struct net_device *const dev = bus->priv;
-@@ -1346,7 +1353,7 @@ mdiobus_write(struct mii_bus *bus, int p
- return 0;
- }
-
--static int mdiobus_reset(struct mii_bus *bus)
-+static int ar2313_mdiobus_reset(struct mii_bus *bus)
- {
- struct net_device *const dev = bus->priv;
-
-@@ -1355,7 +1362,7 @@ static int mdiobus_reset(struct mii_bus
- return 0;
- }
-
--static int mdiobus_probe (struct net_device *dev)
-+static int ar2313_mdiobus_probe (struct net_device *dev)
- {
- struct ar2313_private *const sp = netdev_priv(dev);
- struct phy_device *phydev = NULL;
-@@ -1363,8 +1370,8 @@ static int mdiobus_probe (struct net_dev
-
- /* find the first (lowest address) PHY on the current MAC's MII bus */
- for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
-- if (sp->mii_bus.phy_map[phy_addr]) {
-- phydev = sp->mii_bus.phy_map[phy_addr];
-+ if (sp->mii_bus->phy_map[phy_addr]) {
-+ phydev = sp->mii_bus->phy_map[phy_addr];
- break; /* break out with first one found */
- }
-
---- a/drivers/net/ar2313/ar2313.h
-+++ b/drivers/net/ar2313/ar2313.h
-@@ -162,7 +162,7 @@ struct ar2313_private {
- int unloading;
-
- struct phy_device *phy_dev;
-- struct mii_bus mii_bus;
-+ struct mii_bus *mii_bus;
- int oldduplex;
- };
-
---- a/drivers/net/ar2313/ar2313.c
-+++ b/drivers/net/ar2313/ar2313.c
-@@ -841,6 +841,7 @@ static void ar2313_load_rx_ring(struct n
+--- a/drivers/net/ar231x.c
++++ b/drivers/net/ar231x.c
+@@ -735,6 +735,7 @@ static void ar231x_load_rx_ring(struct n
for (i = 0; i < nr_bufs; i++) {
struct sk_buff *skb;
- ar2313_descr_t *rd;
+ ar231x_descr_t *rd;
+ int offset = RX_OFFSET;
- if (sp->rx_skb[idx]) {
- #if DEBUG_RX
-@@ -862,7 +863,9 @@ static void ar2313_load_rx_ring(struct n
+ if (sp->rx_skb[idx])
+ break;
+@@ -753,7 +754,9 @@ static void ar231x_load_rx_ring(struct n
* Make sure IP header starts on a fresh cache line.
*/
skb->dev = dev;
+ skb_reserve(skb, offset);
sp->rx_skb[idx] = skb;
- rd = (ar2313_descr_t *) & sp->rx_ring[idx];
-@@ -953,6 +956,7 @@ static int ar2313_rx_int(struct net_devi
+ rd = (ar231x_descr_t *) & sp->rx_ring[idx];
+@@ -828,6 +831,7 @@ static int ar231x_rx_int(struct net_devi
/* alloc new buffer. */
skb_new = dev_alloc_skb(AR2313_BUFSIZE + RX_OFFSET + 128);
if (skb_new != NULL) {
skb = sp->rx_skb[idx];
/* set skb */
-@@ -960,13 +964,17 @@ static int ar2313_rx_int(struct net_devi
+@@ -835,13 +839,17 @@ static int ar231x_rx_int(struct net_devi
((status >> DMA_RX_LEN_SHIFT) & 0x3fff) - CRC_LEN);
dev->stats.rx_bytes += skb->len;
/* reset descriptor's curr_addr */
rxdesc->addr = virt_to_phys(skb_new->data);
-@@ -1392,6 +1400,8 @@ static int ar2313_mdiobus_probe (struct
+@@ -1243,6 +1251,8 @@ static int ar231x_mdiobus_probe (struct
return PTR_ERR(phydev);
}
/* mask with MAC supported features */
phydev->supported &= (SUPPORTED_10baseT_Half
| SUPPORTED_10baseT_Full
---- a/drivers/net/ar2313/ar2313.h
-+++ b/drivers/net/ar2313/ar2313.h
-@@ -107,6 +107,8 @@ typedef struct {
+--- a/drivers/net/ar231x.h
++++ b/drivers/net/ar231x.h
+@@ -221,6 +221,8 @@ typedef struct {
*/
- struct ar2313_private {
+ struct ar231x_private {
struct net_device *dev;
+ int (*rx)(struct sk_buff *skb);
+
+++ /dev/null
---- a/arch/mips/kernel/traps.c
-+++ b/arch/mips/kernel/traps.c
-@@ -47,6 +47,7 @@
- #include <asm/mmu_context.h>
- #include <asm/types.h>
- #include <asm/stacktrace.h>
-+#include <asm/time.h>
-
- extern void check_wait(void);
- extern asmlinkage void r4k_wait(void);
-@@ -1514,6 +1515,8 @@ void __cpuinit per_cpu_trap_init(void)
- */
- if (cpu_has_mips_r2) {
- cp0_compare_irq = (read_c0_intctl() >> 29) & 7;
-+ if (get_c0_compare_irq)
-+ cp0_compare_irq = get_c0_compare_irq();
- cp0_perfcount_irq = (read_c0_intctl() >> 26) & 7;
- if (cp0_perfcount_irq == cp0_compare_irq)
- cp0_perfcount_irq = -1;
---- a/arch/mips/include/asm/time.h
-+++ b/arch/mips/include/asm/time.h
-@@ -53,6 +53,7 @@ extern int (*perf_irq)(void);
- #ifdef CONFIG_CEVT_R4K
- extern int mips_clockevent_init(void);
- extern unsigned int __weak get_c0_compare_int(void);
-+extern unsigned int __weak get_c0_compare_irq(void);
- #else
- static inline int mips_clockevent_init(void)
- {
---- a/arch/mips/atheros/board.c
-+++ b/arch/mips/atheros/board.c
-@@ -265,6 +265,11 @@ void (*board_time_init)(void);
- void __init plat_time_init(void) {
- board_time_init();
- }
-+
-+unsigned int __cpuinit get_c0_compare_irq(void)
-+{
-+ return CP0_LEGACY_COMPARE_IRQ;
-+}
- #endif
-
- void __init arch_init_irq(void)
+++ /dev/null
---- a/arch/mips/kernel/cevt-r4k.c
-+++ b/arch/mips/kernel/cevt-r4k.c
-@@ -15,6 +15,22 @@
- #include <asm/cevt-r4k.h>
-
- /*
-+ * Compare interrupt can be routed and latched outside the core,
-+ * so a single execution hazard barrier may not be enough to give
-+ * it time to clear as seen in the Cause register. 4 time the
-+ * pipeline depth seems reasonably conservative, and empirically
-+ * works better in configurations with high CPU/bus clock ratios.
-+ */
-+
-+#define compare_change_hazard() \
-+ do { \
-+ irq_disable_hazard(); \
-+ irq_disable_hazard(); \
-+ irq_disable_hazard(); \
-+ irq_disable_hazard(); \
-+ } while (0)
-+
-+/*
- * The SMTC Kernel for the 34K, 1004K, et. al. replaces several
- * of these routines with SMTC-specific variants.
- */
-@@ -30,6 +46,7 @@ static int mips_next_event(unsigned long
- cnt = read_c0_count();
- cnt += delta;
- write_c0_compare(cnt);
-+ compare_change_hazard();
- res = ((int)(read_c0_count() - cnt) > 0) ? -ETIME : 0;
- return res;
- }
-@@ -99,22 +116,6 @@ static int c0_compare_int_pending(void)
- return (read_c0_cause() >> cp0_compare_irq) & 0x100;
- }
-
--/*
-- * Compare interrupt can be routed and latched outside the core,
-- * so a single execution hazard barrier may not be enough to give
-- * it time to clear as seen in the Cause register. 4 time the
-- * pipeline depth seems reasonably conservative, and empirically
-- * works better in configurations with high CPU/bus clock ratios.
-- */
--
--#define compare_change_hazard() \
-- do { \
-- irq_disable_hazard(); \
-- irq_disable_hazard(); \
-- irq_disable_hazard(); \
-- irq_disable_hazard(); \
-- } while (0)
--
- int c0_compare_int_usable(void)
- {
- unsigned int delta;
projects / openwrt / staging / florian.git / commitdiff